Residential Construction Academy: House Wiring (MindTap Course List)
5th Edition
ISBN: 9781337402415
Author: Gregory W Fletcher
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 9, Problem 3RQ
To determine
The distance from the hole edge to the stud’s face and the thickness of the metal plate for protection of the cable.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Catenary Cable (different level of support)
Determine the angle θ between the two cables.
Determine the angle θ between cables AB and AC.
Chapter 9 Solutions
Residential Construction Academy: House Wiring (MindTap Course List)
Ch. 9 - Prob. 1RQCh. 9 - Prob. 2RQCh. 9 - Prob. 3RQCh. 9 - The minimum amount of free conductor required at...Ch. 9 - Prob. 5RQCh. 9 - Describe how an insulated grounded conduct or...Ch. 9 - Describe how a white Insulated conductor in a...Ch. 9 - Prob. 8RQCh. 9 - Describe how a conductor that is larger than 6 AWG...Ch. 9 - Prob. 10RQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- Determine the angle θ between the two cables attached to the pipe.arrow_forwardA flange bolt coupling has ten steel 25.4 mm diameter bolts evenly tighten around a 415 mm bolt circle. Determine the torque capacity of the connection if the allowable shearing stress in the bolt is 50 MN/m2 . A. 59.95 kN - m B. 52.6 kN - m C. 46.15 kN - m D. 43.8 kN – marrow_forwardDetermine the length of the cables.arrow_forward
- As an Engineer you have to replace the value of 500 Newton to 95 Newton. Find the value of the following: Tension at cable BD Tension at cable BC Note: AB is a solid circular bar.arrow_forwardCatenary Cable (same level of support)arrow_forwardDefine the distance between the adjacent faces of the stock rail and the check rail , is calledarrow_forward
- Discuss the shear ,moment and deflection values when the connection is Pin-Pin and when it is fixed-fixed.arrow_forwardDetermine the angle of twist of the shaft at A relative ot C. Use Gst= 11.0 x 103 ksi.arrow_forward20) what is the weld capacity perpedicular to the beam of the flange connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksiarrow_forward
- The riveted lap connection shown consists of two(2) – PL 12 mm × 280 mm. 1. If diameter of hole equals diameter of rivet, what is the net area of edge-1-3-4-edge in square millimeters? a. 2685.5 b. 2752.5 c. 2792.4 d. 2632.96 2. If diameter of hole equals diameter of rivet, what is the net area of edge-1-2-3-4-edge in square millimeters? a. 5325 b. 4685 c. 2890 d. 3080 3. What is the limiting value of the net area for this steel element with hole (square mm) a. 2880 b. 2646 c. 2856 d. 2080 4. If allowable rupture stress in holes is Fu/2 where Fu is the ultimate strength of the plate and which is equal to 400 MPa, find the maximum allowable force P that can be applied neglecting effect of eccentricity. a. 534.5 kN b. 560.5 kN c. 546.5 kN d. 550.5 kNarrow_forwardProblem 12. A plate is used as a bracket and is attached to a column flange as shown in the figure. The loads are factored loads. The eccentricity of the load is a x = 30 mm; y = 75 mm b x = 45 mm; y = 100 mm c x = 150 mm; y = 250 mm d x = 180 mm; y = 125 mm 13. For the connection shown in problem, the resisting moment of the bolts is a 18 kN - m b 20.915 kN - m c 29.25 kN - m d 36 kN - m 14. For the connection shown in problem 12, using elastic analysis the force on the most stressed bolt is a 21.451 kN b 57.051 kN c 91.415 kN d 180 kN 15. For the connection shown in problem 12, the critical bolt is the bolt located at a upper left b upper right c lower left d lower right 16. For the connection shown in problem, determine the diameter of the bolts if A325X bolts are used. a M16 bolts b M20…arrow_forwardHelp me asap Two poles are 100m away from each other. The difference in elevation of the top of the poles is 10m. A parabolic cable connects them such that the vertical distance of the lowest part of the cable is 5m from the top of the lower pole. If the minimum tension in the cable is 200kN. Find: A. Determine the force of the cable on the lower pole (kN) B. Determine the force of the cable on the higher pole (kN) C. Determine the horizontal distance between lowest part of the cable and the lower pole (m) D. Determine the tension 20m from the higher pole (kN)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Residential Construction Academy: House Wiring (M...Civil EngineeringISBN:9781337402415Author:Gregory W FletcherPublisher:Cengage Learning
Residential Construction Academy: House Wiring (M...
Civil Engineering
ISBN:9781337402415
Author:Gregory W Fletcher
Publisher:Cengage Learning