Bundle: Steel Design, Loose-leaf Version, 6th + Mindtap Engineering, 1 Term (6 Months) Printed Access Card
6th Edition
ISBN: 9781337761505
Author: William T. Segui
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 9, Problem 9.1.3P
To determine
(a)
The moment of inertia of the transformed section.
To determine
(b)
The stress at the top of the steel (indicate whether tension or compression), the stress at the bottom of the steel, and the stress at the top of the concrete.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A rectangular beam has the dimensions (see Figure) b = 12 in, h= 20 in, and d= 17 in. and is reinforced with three
No. 9 (No. 29) bars so that As - 3.00 in?. The concrete compressive strength fe is 4000 psi, and the tensile strength
in bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the stress in the
steel caused by a bending moment M = 10 ft-kips. 9 - 6.78 in, I- 4067 in, Es = 29000000, E - 3600000
L17 in.
20 in.
3 #9 bars
(A, - 3.00 in.)
3 in.
-12 in.-
Select one:
a. 2525 psi
b. 2412 psi
C.
2615 psi
d. 2817 psi
Determine the required tension steel area of the T beam with given properties below.
Width of flange bf = 500 mm
Width of web bw = 340 mm
Thickness of flange tf = 140 mm
Effective depth d = 350mm
Effective concretee covering d' = 75mm
Compressive strength of concrete fc' = 34.5 MPa
Yield stress of steel bar fy = 375 MPa
Mu = 415 kN-m
As = _________ mm2
The concrete post is reinforced axially with four symmetrically placed steel bars, each of cross-sectional
area 900 mm2. Compute the stress in each material when the 1000-kN axial load is applied. The moduli
of elasticity are 200 GPa for steel and 14 GPa for concrete. Compatibiltiy Equation
. Ust
Bearing
|1000 kN
plate
Steel-
Concrete
300 mm
300 mm
Section a-a
Chapter 9 Solutions
Bundle: Steel Design, Loose-leaf Version, 6th + Mindtap Engineering, 1 Term (6 Months) Printed Access Card
Ch. 9 - Prob. 9.1.1PCh. 9 - Prob. 9.1.2PCh. 9 - Prob. 9.1.3PCh. 9 - Prob. 9.1.4PCh. 9 - Prob. 9.1.5PCh. 9 - Prob. 9.1.6PCh. 9 - A W1422 acts compositely with a 4-inch-thick floor...Ch. 9 - Prob. 9.2.2PCh. 9 - Prob. 9.3.1PCh. 9 - Prob. 9.3.2P
Ch. 9 - Prob. 9.4.1PCh. 9 - Prob. 9.4.2PCh. 9 - Prob. 9.4.3PCh. 9 - Prob. 9.4.4PCh. 9 - Prob. 9.4.5PCh. 9 - Prob. 9.5.1PCh. 9 - Prob. 9.5.2PCh. 9 - Prob. 9.5.3PCh. 9 - Note For Problems 9.6-1 through 9.6-5, use the...Ch. 9 - Note For Problems 9.6-1 through 9.6-5, use the...Ch. 9 - Note For Problems 9.6-1 through 9.6-5, use the...Ch. 9 - Note For Problems 9.6-1 through 9.6-5, use the...Ch. 9 - Note For Problems 9.6-1 through 9.6-5, use the...Ch. 9 - Prob. 9.7.1PCh. 9 - Prob. 9.7.2PCh. 9 - Prob. 9.7.3PCh. 9 - Prob. 9.7.4PCh. 9 - Prob. 9.8.1PCh. 9 - Prob. 9.8.2PCh. 9 - A beam must be designed to the following...Ch. 9 - Prob. 9.8.4PCh. 9 - Prob. 9.8.5PCh. 9 - Prob. 9.8.6PCh. 9 - Prob. 9.8.7PCh. 9 - Prob. 9.8.8PCh. 9 - Use the composite beam tables and select a W-shape...Ch. 9 - Prob. 9.8.10PCh. 9 - Prob. 9.10.1PCh. 9 - Prob. 9.10.2P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- Estimate the transverse tensile strength of the concrete in Problem 12.6.arrow_forwardA W21 x 57 floor beam supports a 5-inch-thick reinforced concrete slab with an effective width b of 75 inches. Sufficient steel anchors are provided to make the beam fully composite. The 28-day compressive strength of the concrete is f,c = 4 ksi. a. Compute the moment of inertia of the transformed section. b. For a positive service load moment of 300 ft-kips, compute the stress at the top of the steel (indicate whether tension or compression), the stress at the bottom of the steel, and the stress at the top of the concrete.arrow_forwardThe T-beam shown in figure resulted from monolithic construction of the beam and slab. The effective flange width is 1100 mm and the uniform slab thickness is 120mm. Width of beam is 340 mm, total depth of the T-section is 590 mm. The centroid of steel is 70 mm from extreme concrete fiber. Concrete strength f’c= 21 MPa amd steel strength fy= 415 MPa. 1 Calculate the nominal strength of the beam for positive moment neglecting the contribution of the top reinforcement, KN-m A 428.55 B 503.20 C 355.96 D 637.52 2 Calculate the nominal strength of the beam for negative moment, KN-m A 289.88 B 275.53 C 311.67 D 325.48arrow_forward
- Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mmarrow_forwardQ-A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm² at centre of gravity of the section. The prestress in the tendons is 1000 N/mm². Assuming modular ratio as 10, find the stress (N/mm2) in concrete.arrow_forwardDetermine the required tension steel area of the T beam with given properties below. Width of flange bf = 500 mm Width of web bw = 400mm Thickness of flange tf = 140 mm Effective depth d = 380 mm Effective concrete covering d' = 75 mm Compressive strength of concrete fc' = 30 MPa Yield stress of steel bar fy = 300 MPa Mu = 448 kN-m As = mm2arrow_forward
- A simply supported beam is reinforced with 5-25mm at the bottom And 2-20mm at the top if the beam. Concrete covering to centroid of reinforcement is 70mm at the top and 64 mm at the bottom. The beam has a gross depth of 450 mm and gross width of 300 mm. Fc’=28 mpa fy= 415 mpa. Assume bars are laid out in a single layer. calculate the following if the limiting tensile steel strain is 0.004 for ductile failure: a) depth if neutral axis from the extreme concrete compression fiber ( in mm, in whole number) b) design strength of the beam section ( in kn•m , in whole number) c) maximum service uniform live load over the entire span in Addition to a DL = 20 kn/m ( including weight of the beam) if it has a span of 6 m ( in kn, in whole number)arrow_forwardA reinforced concrete beam has a width of 300 mm and an effective depth of 618 mm. Compressive reinforcement will be placed at d' = 60 mm, f'c = 28 MPa and fy = 415 MPa. Use Ø = 0.9 for flexure and load combination of U= 1.2DL + 1.6LL. Reference: NSCP 2015. a. Calculate the steel ratio for a balanced section, phal- b. Calculate the maximum steel ratio for a tension-controlled section, pmax. d. c. If the beam is to support a bending moment of 240 kN-m from dead load and 195 kN-m from live load, determine the required design flexural strength of the section. If the beam is to support a bending moment of 240 kN-m from dead load and 195 kN-m from live load, determine the number of 28 mmø bars required as tension reinforcement.arrow_forwardconcrete floor slab 100 mm thick is cast monolithic with concrete beam 2.0 m on centers. The beams have a span of 4.2 m and have a web width of 250 mm, and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry; a) effective flange width of an interior beam in mm b) depth of uniform stress block at ultimate stage in mm ( round of to nearest whole number) c) tensile steel strain compatible with concrete strain if 0.003 ( round if 3 decimal places)arrow_forward
- A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.2 m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameters bars in two rows with 25 mm vertical clear spacing. Use material strengths f'c = 21 MPa and fy = 415 Mpa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm Depth of uniform stress block at ultimate stage in mm to the nearest whole number Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal placesarrow_forwardA rectangular beam has the dimensions (see Figure) b = 12 in., h - 20 in, and d 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in. The concrete compressive strength fe is 4000 psi, and the tensile strength In bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the concrete compression stress at the top fiber caused by a bending moment M- 10 ft-kips. 9- 6.78 in, I= 4067 in, Es= 29000000, E = 3600000 17 in. 20 in. 3 #9 bars (A, - 3.00 in.?) 3 in. -12 in- Select one: a. 390 psi b. 1390 psi c. 200 psi d. 250 psiarrow_forwardA doubly reinforced concrete beam of size 250 mm x 500 mm overall depth is reinforced with 2-12 mm dia. bars in compression zone and 3-20 mm dia. bars in tension zone, each at an effective cover of 40 mm. The grade of concrete and steel are M20 and Fe415 respectively. The strain in compression steel will be [Take stress in compression steel as 345 MPa]arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning
Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Steel Design (Activate Learning with these NEW ti...
Civil Engineering
ISBN:9781337094740
Author:Segui, William T.
Publisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning