Respiratory Structure Homework-1 (1) (1)

4

A lead block is suspended from your hand by a string. The reaction to the force of gravity on the block is the force exerted by: O the block on the string. the string on the hand. O the block on Earth. O the string on the block. none of the given choices

Question 12 The picture shows a pulley system moving a one-kilogram weight. What is the mechanical advantage of this system? A 3 Illuminate EducationTM, Inc.

part 3 and 4

A submarine robot explorer is used to explore the marine life in deep water. The weakest point in the submarine robot explorer structure can hold a pressure force of 300 MPa. What is the deepest point can it reach? *

For the following figure, draw a kinematic diagram for each identifyingthe point of interest. From there, calculate the mobility of the device.

Name: Q1/ Give the Name of plans in the Image? The anatomical planes www.free-anatomy-quiz.com Q2/ Give the correct answer (1 or 2 word) 1- An inferior movement of the shoulder girdle 2- Bringing your wrist toward your shoulder at the elbow joint 3-Relating to the right and left sides of the body or of a body structure such as the right & left extremities 4-Medial Movement toward the midline 5-Movement along a straight line 6-imaginary line perpendicular to the plane of rotation and passing through the center of rotation 7-a body or group of bodies whose motion is being analyzed

Find GERF and then using the method of Joints find the forces in all members. Make sure you provide all the angles and magnitude of all the forces in a table stating Compression or Tension. You can use cm to draw the structure.   At work, I need to represent data in a table indicating Tension or Compression and the angle. I need  it table please

DUE NOW. Please answer it correctly and as immediately as possible. Thank you!

Please solve all three.

For the following figure, draw a kinematic diagram for each identifyingthe point of interest. From there, calculate the mobility of the device.

Write and explain all calculations involved. ps/ Please write it with simple handwriting so i can read it easy.

3. if you had to lift a truck and had a pole, a rope and a fulcrum, you could do it! A kid could do it! What kind of lever would you build? class lever a. first b. second 3.third 4.forth

The tension is growing!Context At your summer job, your supervisor wants to test your physics skills. A new winch (a cable driven by a motor) is to be used to hoist loads up an inclined ramp. Your supervisor is worried about the packages arriving too quickly at the top of the ramp. Constraints The inclined ramp is made up of small cylinders that are free to rotate: there is no friction between the ramp and the load.The angle theta of the ramp from the horizontal is known.The winch cable exerts a known force.The cable is oriented at an angle a from the horizontal.The charge, initially immobile, has a known mass.The length of the ramp is known. Schematization Draw a diagram of the object that interests us. Draw your x and y axes. Draw and name each force experienced by the object that interests us. Modelization Build a model to calculate the final speed of the load as it arrives at the top of the ramp, given the known parameters. Then test your model with the following values: Ramp…

Typewritten for an upvote. No upvote for handwritten. Please skip if you have already done this. Thank you

please find the solution

1–2. Figure C1.2 shows a mechanism that is typical in the tank of a water closet. Note that flapper C is hollow and filled with trapped air. Carefully examine the configuration of the components in the mechanism. Then answer the following leading questions to gain insight into the operation of the mechanism. 1. As the handle A is rotated counterclockwise, what is the motion of flapper C? 2. When flapper C is raised, what effect is seen? 3. When flapper C is lifted, it tends to remain in an upward position for a period of time. What causes this tendency to keep the flapper lifted? 4. When will this tendency (to keep flapper C lifted) cease Plz connect me if you want to explan subject for me .... +962 79180149 Thx

Please write down part a on a worksheet and the part b,c in python. Given: All internal angles are 60 degrees and all side lengths are 4 inches. There is a pin joint at location 1, and a roller at location 5.

This is the full question please if you unable to answer let me know, don’t provide me with wrong answer please

Z3

Select the correct statements for processing forces in Free Body Diagram (FBD). (Select 2) Physical supports are replaced by forces.   The Law of parallelogram is used to add forces graphically   When drawing FBD, weight is the first to be considered.   Friction forces are not considered in the FBD

Please answer fast

You must have to draw the free body diagram. Please don't make any mistakes. I will rate as soon as i receive the solution. (Strictly don't use chatgpt)

You are a mechanical engineer tasked with overseeing the equipment used in constructing a high-rise. A tower crane, used to lift and move heavy construction loads, is being used in the construction site.

Help!!! Answer it correctly!!! Please

I only need parts D and E, thank you!

The second picture is continuation of first image.

Good day. I am trying to review for examinations and require assistance for these questions... Horse Power: An amount of work performed is 11,500ft-lb per seconds. How much hp is expended in this case?    Piston Displacement: A four-cylinder aircraft engine has a total displacement of 275 cu. in. What is its cylinder bore or diameter if each of the four cylinders has a stroke of six inches?   Compression Ratio: If there are 243 cubic inches of space in the cylinder when the piston is at the bottom and there are 27 cubic inches of space when the piston is at the top of the stroke. Find CR and V1 (Litre).   **Would appreciate a detailed explanation. Thank you so much.

Help!!! Please answer all Correctly!!! Please

3. In a science fiction story about space exploration an expedition to Mars was described. The space ship landed in a rocky valley and the astronauts promptly prepared their vehicle for a trip on the planet's surface. This special vehicle was designed with big inflated tires. On the very first steep slope the vehicle tipped over. They did have small steel balls onboard to increase traction. They thought of suspending a bunch of them beneath the vehicle to lower its center of gravity, but that would decrease the clearance and cause the weights to strike rocks and the ground more often How could it be done?

Please solve it in a handwritten format with a free body diagram. Don't use chat gpt. (Diagram is mandatory) Mechanical engineering -