ABA Terminology Flashcards - Unit 7 Transcript

please help solve A-F. thank you You are an engineer working on a project and your prototype has failed prematurely. You question whether or not a key component of the prototype was manufactured with the correct material. There are two way to check for the material properties. The first way is to have a material certification done to confirm the exact material composition. This will take some time. The second method to confirm the material properties is to make an ASTM test sample and test for the material properties. This tensile test was completed on a test sample with an initial diameter of .501” and an initial length of 2”. The Load-Deflection data for this tensile test is below. Use this data to answer the first set of questions on the Final Exam in eLearning. A. Determine the Ultimate Tensile Strength B. Determine the 0.2% Offset Yield Strength C. Determine the value of the Proportional Limit D. Determine the Modulus of Elasticity E. Determine the Strain at Yield F. Calculate %…

I need parts 8, 9, and 10 answered. Number 1 is an example of how it should be answered. NOTE: Read the instructions, no where does it say any drawing is required. It is really frustrating when I wait all this time for an answer to a question and some tutor does even read the instructions and just declines it...its ridicilous.

Don't use chatgpt will upvote

SUBJECT COURSE: ERGONOMICS REQUIRED: CONCLUSION AND RECOMMENDATION FOR THE FOLLOWING SCENARIO: (should be 2 paragraphs with 7 sentences each) We carried out a lab experiment on the stroop test. According to the results of our analysis using Minitab ANOVA, there was no error made when we were carrying out the task. here are the objectives of the task: Students should be able to: 1. Understand how human brains process information. 2. Demonstrate compatibility and interference issues. 3. Determine how noise or interference affects perception.

This is an engineering problem and not a writing assignment. Please Do Not Reject. I had other engineering tutors on bartleby help me with problems similar to this one. This problem must be presented in a logical order showing the necessary steps used to arrive at an answer. Each homework problem should have the following items unless otherwise stated in the problem: a. Known: State briefly what is known about the problem. b. Schematic: Draw a schematic of the physical system or control volume. c. Assumptions: List all necessary assumptions used to complete the problem. d. Properties: Identify the source of property values not given to you in the problem. Most sources will be from a table in the textbook (i.e. Table A-4). e. Find: State what must be found. f. Analysis: Start your analysis with any necessary equations. Develop your analysis as completely as possible before inserting values and performing the calculations. Draw a box around your answers and include units and follow an…

I need answers to questions 7, 8, and 9 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

I need parts 1, 2, and 3 answered pertaining to the print provided. NOTE: If you refuse to answers all 3 parts and insist on wasting my question, then just leave it for someone else to answer. I've never had an issue until recently one single tutor just refuses to even read the instructions of the question and just denies it for a false reasons or drags on 1 part into multiple parts for no reason.

Astronomy Question:  Read the questions slowly and answer with precise and long details about each of the questions. Answer correctly and follow my guidelines for a long and wonderful review after results. Your target/main observable galaxy is the whirlpool galaxy. Target: Whirlpool Galaxy Object Type: Galaxy Distance: 37 million light-years Constellation: Canes Venatici. DO NOT COPY AND PASTE OTHER WORK OR THINGS FROM THE INTERNET, use your own words.Provide refernces if used In 500 words, please explain the relevance of this object to the physics course material in university andits importance to astronomy. (Some question you may seek to answer are: What beyond the objectitself is learned by studying this class of objects? What sorts of telescopes and observations would beneeded for more detailed, broader reaching studies of this source and objects of its nature?)

I need answers to problems 7, 8, and 9.  NOTE: Please stop wasting my time and yours by rejecting my question because it DOES NOT REQUIRE YOU TO DRAW anything at all. They are simple questions pertaining to the print provided. READ THE INSTRUCTIONS of the assignment before you just reject it for a FALSE reason or leave it for someone to answer that actually wants to do their job. Thanks.

hello i hope you are fineI need your help by solving the question below. Please, please, please quickly, because I am studying now and I have exams in the coming days, so I need to do this homework in order to understand the study material and I do not have much time. I need to solve within half an hour or a little more.      It's kind of fill in the blank please give me the best word possible   the question is :           1-The graphitization of cast iron effected by ………………………..?         2-The hardness test techniques differs among themselves according to …………………….?           3-The main advantages of grey cast iron are ………………………….?           4-The solid materials deform by ……………………., while , liquids deform by ………………..?           5-The main rules that must be taken in order to increasing the accuracy of hardness test, are ………………..?         6-Nodular iron more ductile than grey iron, because …………..?…

Please make the charts for the questions. Please refer to Successful Project Management (7th Edition). Attached is the example Thank you.

I need problems 6 and 7 solved.  I got it solved on 2 different occasions and it is not worded correctly. NOTE: Problem 1 is an example of how it should be answered. Below are 2 seperate links to same question asked and once again it was not answered correctly. 1. https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857 2. https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/bd5390f0-3eb6-41ff-81e2-8675809dfab1

I need answers for problems 13, 14, and 15 pertaining to the print provided.   NOTE: If you refuse to answers all 3 parts and insist on wasting my question by breaking down 1 simple question into 3 parts, then just leave it for someone else to answer. Thank you.

Please anwer the quesiton correctly and take your time, i read the guideline and honor code and im allowed to have Submit only one question at a time under the appropriate subject. A question can have up to 3 subparts (i.e. part a, b, and c). Here is the link that says from bartleby if you odnt belive me: https://bartleby.zendesk.com/hc/en-us/articles/360017462394-How-can-I-ensure-my-questions-get-answered-as-quickly-as-possible-So answer all the questions thanks.Calculate the frequency of a radio wave.1. A) radio wave has a wavelength of 21 cm. What is the wavelength in meters? (Give your answer in meters rounded to exactly 2 decimal places).B)Use your previous answer and the speed of light (c = 3 · 108 m/s) to calculate the frequency of a 21 cm radio wave. Give your answer in Hz, no decimal places.C)Use your previous answer to calculate the frequency of a 21 cm radio wave. This time, give your answer in GHz, rounded to exactly one decimal place. (Note that 1 GHz = 109 Hz).

Help can only be sought via private Ed Discussion posts or instructor office hours. - In all coding, use only functions covered in class. It will be considered a violation of the Academic Integrity Policy if you use any build-in functions or operators of Matlab that calculate the inverse of a matrix, interpolations, spline, diff, integration, ode, fft, pdes, etc.; - You may reuse functions you yourself developed throughout this semester in this class or from solutions posted on Canvas for this class. Problem Description (CCOs #1, 2, 3, 4, 5, 6, 7, 8, 11, 12) A water tank of radius R = 1.8m with two outlet pipes of radius r₁ = 0.05m and r2 installed at heights h₁ = 0.13m and h₂ = 1m, is mounted in an elevator moving up and down causing a time dependent acceleration g(t) that must be modeled as g(t) = go+a1 cos(2π f₁t) + b₁ sin(2π f₁t) + a2 cos(2π f₂t) + b₂ sin(2π f₂t), (1) Figure 1: Water tank inside an elevator The height of water h(t) in the tank can be modeled by the following ODE,…

Important instruction: These questions use the last three-digit value (L3D) of individual student matrix numbers. For example, if the matrix number is CD180264 then the L3D value is 264 (since the last three digits is 264). Some data require multiplication of the L3D value, for example, 10(L3D) means 10 x L3D   subject name is INDUSTRIAL ENGINEERING

I need answers to questions 13, 14, and 15 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

I think understand the concept but I'm stuck on how allowance and tolerance are did. I wasn't sure if I was supposed to write separate numbers for allowance then the two for tolerance. Or am I supposed to use the number I get from allowance to calculate tolerance. I've read pages but feels like my brain is like not connecting the dots or I misread something.

I need answers to questions 13, 14, and 15 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

I have two parts that need to be answered (Multiple Choice). If you can not answer both parts, please leave it for another tutor to answer. Thank you.   On the left side view of this print, there is a horizontal, straight-line segment that does not connect to other lines. In basic terms, explain why. (Multiple Choice)A: It represents a rounded edge and is there to help clarify the view, even though no sharp edge exists.B: It represents a straight edge that can't be seen in other views.C: It's a drafting mistake and should not be there.D: It represents a locating edge on the part and must be there to establish a primary plane for the inspection setup. This print does not show a cutting-plane line. Is this acceptable practice or an error? (Multiple Choice)A: AcceptableB: Error

Answer letter C. Thank you

Engineering Management : Please Read your Reference: www.bigrentz.com for your own. Topic is " Top 10 Construction Industry Trends To Watch For In 2022" Answer The following this. Make a reaction paper of the statement. In precisely five paragraphs, minimum of five sentences per paragraph, discuss your stand regarding the statement with at least 5 reliable references supporting your reaction. CONSTRUCTION Top 10 Construction Industry Trends To Watch For In 2022 By: BigRentz, Inc. on December 13, 2021 in 2022

Solve correctly

For the air compressor shown in Figure below, the air enters from a large area and exit from small one, explain why? Instructions for answering this question: The answer to this questian is required as handwritten where you are aiso required to add a Handwritten integrity Statement. Pieose follow the below steps: 1 Write on a blank poper your AUM student ID, full name, course code, section and date 2 Write the following integrity statement and sign: "7 offirm that I have neither given nor received any help on this assessment and that personally compieted it on my own." 3. Write your onswer to the obove question as required 4. Put your Original Civil ID card or AUM ID card on the poper 5 Toke o picture or scan, and uplood Important note: if handwritten document is submitted without the integrity stotement including ID (Civil ID or AUM ID), then the related handwritten question(s) will not be groded.

all one question help asap please!

I need help solving these 3 simple parts, if you can not answer all 3 parts then please leave it for another tutor, thank you.

Why was Ford assembly line so productive 

Directions: Answer the questions after each situation. 1. David Aquino, engineering director, started out the day uptight. His young child had the flu the night before, and he had been up all night to help. Upon arrival at his office, David had to make urgent phone calls to approve a two-week overtime work plan due to a plant fire the night before and to plan for a product committee meeting the next day to counter environmental concerns about a wastewater treatment plant. Then he spent 30 minutes reviewing the qualifications of new candidates and decided on one. He asked for salary information and wanted to examine the offer before it was sent. He asked for further justification for the budget requested by industrial engineering for a minicomputer. Without reading it, he approved the research proposal from material engineering. He rejected an invitation to speak at a regional meeting of the Philippine Society of Mechanical Engineers by giving an untrue reason. David made a note for the…

My English Public speaking course teacher instructed me to make a persuasive speech about " Every automobile driver should be required to take a new driver's test every three years"  The speech should be about 4-5 minutes long.  Please make the speech at your own words, please please please  . I will rate you positive if you do so. Thank you so much.

1. HI CAN YOU HELP ME WITH MY ASSIGNMENT. PLEASE WRITE IT PROPERLY, DONT WRITE IT.      Faculty members and staff from ABC University had a meeting on how they will conduct the virtual flag ceremony every Monday. There are reported 12 faculty members, 3 office staff, 4 heads from the different courses and 1 student leader attended a secret meeting in a room which is 15 meters wide by 10.5 meters long and a ceiling of 3.87meters. The room is completely sealed off and insulated. Each persons gives off 150kcal per hour of heat and occupies a volume of 0.2 cubic meter. The room has an initial pressure of 14.696psi and temperature of 522.27 Rankine. • Calculate the room temperature after 15.5 minutes In Celcius • What is the mass of air in kilograms

Put together a short presentation (pitch) for a mechanical engineering student, emphasizing his period of the course (10th) and his most significant achievements such as his change from the naval to mechanical course, the learning of programming languages focused on data analysis (Python and SQL), since the engineering course does not explore these skills,  and the improvement of Excel with the VBA language.

TOPIC: ENGINEERING ECONOMICS SPECIFIC INSTRUCTION: Solve each problem NEATLY and SYSTEMATICALLY. Show your COMPLETE solutions and BOX your final answers. Express all your answers in 2 decimal places. PROBLEM: Cardinal Financing lent an engineering company Php 500,000 to retrofit an environmentally unfriendly building. The loan is for 5 years at 10 % per year simple interest. How much money will the firm repay at the end of 5 years?

! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. At an intersection car B was traveling south and car A was traveling 30° north of east when they slammed into each other. Upon investigation, it was found that after the crash, the two cars got stuck and skidded off at an angle of 10° north of east. Each driver claimed that he was going at the speed limit of 50 km/h and that he tried to slow down, but couldn't avoid the crash because the other driver was going a lot faster. The masses of cars A and B were 1500 kg and 1200 kg, respectively. 10° 30° VR Determine the speed of the faster of the two cars if the slower car was traveling at the speed limit. The speed of the faster car was km/h.

Help!!! Please answer part b correctly like part A. Please!!!!

Subject: the language English material, Max 30 minutes, I want to solve this question , please

The first photo is the question, where the 2nd shows some problem solving strategies