Victoria Pearson-HI255-Unit 5 assignment
.docx
keyboard_arrow_up
School
American Public University *
*We aren’t endorsed by this school
Course
255
Subject
Mechanical Engineering
Date
Apr 3, 2024
Type
docx
Pages
3
Uploaded by victoriaeliza
HI255 Medical Coding II
Unit 5 Assignment Worksheet
Unit outcomes addressed in this Assignment:
Identify unusual services and treatments and report them
accurately.
Abstract physician documentation of procedures on the integumentary system.
Accurately apply the guidelines for coding procedures on
the musculoskeletal system.
Recognize the details required to accurately report procedures on the respiratory system.
Identify guidelines to correctly report services to the cardiovascular system.
Determine how to accurately report procedures on the genital systems: male and female.
Interpret documentation to accurately report procedures on the nervous system.
Recognize the necessary details to report procedures on the eye, ocular adnexa, and auditory system.
Course outcome addressed in this Assignment:
HI255-3:
Assess national guidelines and best practices to ensure quality coding.
HI255-4:
Evaluate clinical documentation for appropriate health information that supports quality coding practices.
AHIMA’s Professional Coding Approved Program (PCAP) Mapping: Domain IV. Revenue Cycle Management
IV.1. Determine diagnosis and procedure codes and groupings according to official guidelines. (Bloom’s level 5)
Instructions: Each question requires you to access and review the indicated patient case. Cases can be downloaded as PDF files from the Patient Records folder in Course Documents. Review the medical record and answer the question indicated. Pay close attention to the question—is the answer a diagnosis code or procedure code or both? If a procedure, remember PCS codes are only used for IP (inpatient) charts. DO NOT CODE LAB TESTS OR PLAIN X-RAYS UNLESS SPECIFIED. Type your answers in the “Student Response” column.
Q#
Case Questions
Student
Response
Instructor Use
1
Download and abstract case OPSX32-Sandall, Oscar
Locate and assign the principal and additional ICD-
10-CM codes
using the ICD-10-CM manual. Select the pair of diagnosis codes from the following:
S83.211A, M67.861 | M23.203, M67.52 | S83.232A, M67.51 | S83.231A, M67.51
ALSO,
locate and assign the principal CPT procedure code
using the CPT manual. Select the single procedure code from the following:
29883 | 29880-RT | 29881-RT | 29870
S83.231A
M67.51
29881-RT
2303B
HI255 Unit 5 Assignment Worksheet
1
HI255 Medical Coding II
2
Download and abstract case SXP01-Williams, Carrie
Locate and assign the principal ICD-10-CM code
using the ICD-10-CM manual. Select the single diagnosis code from the following:
K29.50 | K29.21 | K29.81 | K29.00
ALSO,
locate and assign the principal CPT procedure code
using the CPT manual. Select the single procedure code from the following:
88300 | 88305 | 88305X2 | 88309
K29.50
88305X2
3
Download and abstract case IMG21-Currier, Frank
Locate and assign the principal ICD-10-CM code
using the ICD-10-CM manual. Select the single diagnosis code from the following:
J84.10 | J84.113 | R09.0 | R06.0
ALSO,
Locate and assign the principal CPT procedure code
using the CPT manual. Select the CPT procedure code from the following:
94621 | 94619 | 94760 | 94618
J84.10
94618
4
Download and abstract case OPSX34-Clerk, Solomon
Locate and assign the principal CPT procedure code
using the CPT manual. Select the procedure code from the following:
29827-RT | 29828-RT | 29806-RT | 29820-RT
ALSO,
locate and assign the additional (add-on) CPT
procedure code
using the CPT manual. Select the procedure code from the following:
29828-RT | 29820-RT | 29806-RT | 29826-RT
29827-RT
29826-RT
5
Download and abstract case IPC22-Sapp, Eric
Locate and assign the principal ICD-10-CM code
using the ICD-10-CM manual. Select the diagnosis code from the following:
R78.81 | R78.8 | A41.9 | R65.21
ALSO,
locate and assign the additional ICD-10-CM code
using the ICD-10-CM manual. Select the diagnosis code from the following:
B95.6 | B95.4 | B95.62 | B95.8
R78.81
B95.8
6
Download and abstract case OPSX31-Mayweather, Cora.
Locate and assign the principal and 2 additional ICD-10-CM codes
using the ICD-10-CM manual. C56.3
C78.5
Z93.3
36561
2303B
HI255 Unit 5 Assignment Worksheet
2
Your preview ends here
Eager to read complete document? Join bartleby learn and gain access to the full version
- Access to all documents
- Unlimited textbook solutions
- 24/7 expert homework help
Related Questions
You are assigned as the head of the engineering team to work on selecting the right-sized blower that will go on your new line of hybrid vehicles.The fan circulates the warm air on the inside of the windshield to stop condensation of water vapor and allow for maximum visibility during wintertime (see images). You have been provided with some info. and are asked to pick from the bottom table, the right model number(s) that will satisfy the requirement. Your car is equipped with a fan blower setting that allow you to choose between speeds 0, 1,2 and 3. Variation of the convection heat transfer coefficient is dependent upon multiple factors, including the size and the blower configuration.You can only use the following parameters:
arrow_forward
Please answer the 4th question
arrow_forward
MECT361
Mechatronics Components and Instrumentation
PLEASE GIVE ME THE short answer and wite it by keyword
thanks
arrow_forward
I need help answering problems 4, 5, and 6 pertaining to the print provided in the attachment.
arrow_forward
Hartley Electronics, Inc., in Nashville, producesshort runs of custom airwave scanners for the defense industry.The owner, Janet Hartley, has asked you to reduce inventory byintroducing a kanban system. After several hours of analysis, youdevelop the following data for scanner connectors used in onework cell. How many kanbans do you need for this connector?Daily demand 1,000 connectorsLead time 2 daysSafety stock 12 dayKanban size 500 connectors
arrow_forward
Please recheck and provide clear and complete step-by-step solution in scanned handwriting or computerized output thank you
arrow_forward
Please give me the answers for this i been looking at this for a hour and my head hurts
arrow_forward
Please recheck and provide clear and complete step-by-step solution/explanation in scanned handwriting or computerized output thank you
arrow_forward
I need help solving these 3 simple parts, if you can not answer all 3 parts then please leave it for another tutor, thank you.
arrow_forward
For the air compressor shown in Figure below, the air enters from a large area and
exit from small one, explain why?
Instructions for answering this question: The answer to this questian is required as handwritten where you are
aiso required to add a Handwritten integrity Statement. Pieose follow the below steps:
1 Write on a blank poper your AUM student ID, full name, course code, section and date
2 Write the following integrity statement and sign:
"7 offirm that I have neither given nor received any help on this assessment and that personally compieted it
on my own."
3. Write your onswer to the obove question as required
4. Put your Original Civil ID card or AUM ID card on the poper
5 Toke o picture or scan, and uplood
Important note: if handwritten document is submitted without the integrity stotement including ID (Civil ID or
AUM ID), then the related handwritten question(s) will not be groded.
arrow_forward
Important instruction: This question uses the last three-digit value (L3D) of individual student matrix number. For example, if the matrix number is CD180264 then the L3D value is 264 (since the last three digits is 264). Some data require multiplication of the L3D value, for examAdditional instruction: These questions use the last three-digit value (L3D) of individual student matrix number. Example, if the matrix number is CD180264 then the L3D value is 264 (since the last three digits is 264). Some data require multiplication of the L3D value, for example 10(L3D) means 10 x L3D.ple 10(L3D) means 10 x L3D.
subject name is
arrow_forward
I need help solving problems 10, 11, and 12 pertaining to the print provided.
arrow_forward
O Web C x
k GECO0 X
O Course X
O Assign X
O Web C x
k MATHO X
Assign X
O Discus: X
O Quizze
O Syllabu x
O Grade: x
om/courses/31937/assignments/1001318?module_item_id=2616268
tructions:
ollow the prescribed format by the course policy
pu have 48 hours to answer and submit the solution.
olve the problem with complete and detailed solution.
7x+14]
-x
1.
What value of x satisfies the matrix equation
(2 points)
3x-2
x+8
2.
Solve for x and y in the matrix equation below:
3 -4
y
x-y 4
2] [10
-1]
3 -1]
%3D
(3 Points)
-1
[2 -3]
x -8
2
6х -9
-3 3х
|1 -2
2
and
the matrix 3(A +2B) is equal to? (3 points)
3.
For matrices A=| 0
%3D
7 -2
3 -1
[2 -3
The matrix product
2 4 ?(2 points)
4.
0 1
1
4,
arrow_forward
A nearsighted eye is corrected by placing a diverging lens in front of the eye. The lens will create a virtual image of a distant object at the far point (the farthest an object can be from the eye and still be in focus) of the myopic viewer where it will be clearly seen. In the traditional treatment of myopia, an object at infinity is focused to the far point of the eye. If an individual has a far point of 39.5 cm, prescribe the correct power of the lens that is needed. Assume that the distance from the eye to the lens is negligible.
arrow_forward
A Team of Engineers asked for an internal combustion engine to use it in a designed car. Your role is to describe the operation sequence of different types of available engines, explain their mechanical efficiency, and deliver a detailed technical report to show your approach in solving and discussing the following tasks and issues.
You must follow the following steps to help the team:
STEP 1
Describe the operational sequence of four-stroke spark ignition and four-stroke compression ignition engines with the aid of sketches by constructing simple sketch representing the operation and plotting the P-V diagrams for each process during the cycle to show the following:
The input and output heat and net output work
The air-fuel mixture intake and exhaust gasses
The spark plug when it is in the active mode
arrow_forward
A Team of Engineers asked for an internal combustion engine to use it in a designed car. Your role is to describe the operation sequence of different types of available engines, explain their mechanical efficiency, and deliver a detailed technical report to show your approach in solving and discussing the following tasks and issues.
You must follow the following steps to help the team:
STEP 1
Describe the operational sequence of four-stroke spark ignition and four-stroke compression ignition engines with the aid of sketches by constructing simple sketch representing the operation and plotting the P-V diagrams for each process during the cycle to show the following:
The input and output heat and net output work
The expansion and compression strokes
The air-fuel mixture intake and exhaust gasses
The spark plug when it is in the active mode
The complete cycle of ideal Otto and Diesel cycles that shows the input and output heat and net output work.
STEP 2
Explain the mechanical…
arrow_forward
I need answers for problems 13, 14, and 15 pertaining to the print provided.
NOTE: If you refuse to answers all 3 parts and insist on wasting my question by breaking down 1 simple question into 3 parts, then just leave it for someone else to answer. Thank you.
arrow_forward
Problem 3:
Insulation
To=1
Toowwww
Steam
Tx2
T₂ T3
www www
R₁ R₁ R₂
www.T
R₂
Steam at T1 = 320 °C flows in a cast iron pipe (k= 80 W/m. °C) whose inner and outer diameters are
5 cm = 0.05 m and D₂ = 5.5 cm = 0.055 m, respectively. The pipe is covered with 3-cm-thick glass wool
insulation with k = 0.05 W/m. °C. Heat is lost to surroundings at T2 = 5 °C by natural convection and
radiation, with a combined heat transfer coefficient of h₂ = 18 W/m². °C. Taking the heat transfer coefficient
inside the pipe to be h₁ = 60 W/m². °C, determine the temperature drops across the pipe and the insulation.
The determination is based on a unit length of the pipe (L = 1 m).
Assumptions
1. Heat transfer is one-dimensional since there is no indication of any change with time.
2.
Heat transfer is one-dimensional since there is thermal symmetry about the centreline and no
variation in the axial direction.
3. Thermal conductivities are constant.
4. The thermal contact resistant at the interface is…
arrow_forward
I need help with problems 1, 2, and 3 pertaining to the print provided below.
arrow_forward
The Weather Monitor. Your South American expedition splits into two groups: one that stays at home base, and yours that goes off to
set up a sensor that will monitor precipitation, temperature, and sunlight through the upcoming winter. The sensor must link up to a
central communications system at base camp that simultaneously uploads the data from numerous sensors to a satellite. In order to
set up and calibrate the sensor, you will have to communicate with base camp to give them specific location information.
Unfortunately, the group's communication and navigation equipment has dwindled to walkie-talkies and a compass due to a river-raft
mishap, which means your group must not exceed the range of the walkie-talkies (3.0 miles). However, you do have a laser rangefinder
to help you measure distances as you navigate with the compass. After a few hours of hiking, you find the perfect plateau on which to
mount the sensor. You have carefully mapped your path from base camp around lakes and…
arrow_forward
I need help answering questions 4, 5, and 6 pertaining to the print provided below.
arrow_forward
Identify the lines
arrow_forward
Show the dimensions of the object on its orthographic views.
arrow_forward
The question and data are in pictures.
Please answer properly with each steps and explanation.
Best of luck.
Thank you so much in advance.
arrow_forward
In the automotive industry, supercars are highly accredited with how they are manufacture; from the
type of car chassis used to the type of materials employed. Often enough, companies like BMW,
Mercedes & Audi produces supercars that exemplifies a better reliability compared to other automotive
manufacturing companies. This is because they pay close attention to the details on how the car is
manufactured; right from raw materials to a finished supercar. The task given to you is to watch the
video link provided below & explain the electrostatic process acquired for the two different models of
BMW vehicles.
https://www.youtube.com/watch?v=sUqKUbmdOr0
Pls watch the video before answering
arrow_forward
I could not figure this problem during lecture please help me solve it! ANSWER ALL OR DO NOT ATTEMPT
arrow_forward
Read each statement carefully and answer by True or False (if False then, correct
the statement).
1- Process control combines how physics, chemistry, and biology work in
operating equipment and an understanding of dynamic systems.
2- When a second letter is used in instrumentation symbols, e.g., Pressure
Indicator Controller (PIC), it defines the measured or initiating variables.
3- P&ID contains the sensor details such as physical principle and
measurement range.
4- FRC 82516: Flow Recording Controller, area no 825, process unit 8, loop
number 16.
5- P&ID excludes equipment identification.
arrow_forward
AutoCAD is a computer aided drafting and design system implemented
on a personal computer. *
true
O false
arrow_forward
4. Documents business requirements use-case narratives.for only one process
note: please i want Documents like this in pic
arrow_forward
AutoSave
STATICS - Protected View• Saved to this PC -
O Search (Alt+Q)
Off
ERIKA JOY DAILEG
EJ
File
Home
Insert
Draw
Design
Layout
References
Mailings
Review
View
Help
Acrobat
O Comments
E Share
PROTECTED VIEW Be careful-files from the Internet can contain viruses. Unless you need to edit, it's safer to stay in Protected View.
Enable Editing
Situation 9 - A 6-m long ladder weighing 600 N is shown in the Figure. It is required to determine
the horizontal for P that must be exerted at point C to prevent the ladder from sliding. The
coefficient of friction between the ladder and the surface at A and B is 0.20.
25. Determine the reaction at A.
26. Determine the reaction at B.
27. Determine the required force P.
4.5 m
1.5 m
H=0.2
30°
Page 5 of 5
671 words
D. Focus
100%
C
ЕPIC
GAMES
ENG
7:24 pm
w
US
16/02/2022
IZ
arrow_forward
INSTRUCTIONS:
Please write clearly and understandable way.
Write all the corresponding GIVEN with their corresponding symbols and units.
List all the MISSING/REQUIRED, and list all the FORMULA that will be used.
• DRAW/ILLUSTRATE THE DIAGRAM/CIRCUIT OR DRAWINGS that is related to the
problem, IF POSSIBLE, which is HIGHLY REQUIRED.
The CONVERSION calculations with their corresponding symbols and units is
required.
The problem's SOLUTION must be solved in a step-by-step, no shortcut, again, with
their corresponding symbols and units.
• BOXED the Final Answer.
PROBLEM:
The compressor of a large gas turbine power plant receives 12kg/s of surrounding air at
95kPa and 20°C. At the compressor outlet, air exits at 1.52MPa, 430°C, Determine the
flow energy requirements in MW.
a) 1.412
b) 2.42
c) 1.01
d) 1.614
arrow_forward
I need problems 6 and 7 solved.
I got it solved on 2 different occasions and it is not worded correctly.
NOTE: Problem 1 is an example of how it should be answered. Below are 2 seperate links to same question asked and once again it was not answered correctly. 1. https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
2. https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/bd5390f0-3eb6-41ff-81e2-8675809dfab1
arrow_forward
SEE MORE QUESTIONS
Recommended textbooks for you
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Related Questions
- You are assigned as the head of the engineering team to work on selecting the right-sized blower that will go on your new line of hybrid vehicles.The fan circulates the warm air on the inside of the windshield to stop condensation of water vapor and allow for maximum visibility during wintertime (see images). You have been provided with some info. and are asked to pick from the bottom table, the right model number(s) that will satisfy the requirement. Your car is equipped with a fan blower setting that allow you to choose between speeds 0, 1,2 and 3. Variation of the convection heat transfer coefficient is dependent upon multiple factors, including the size and the blower configuration.You can only use the following parameters:arrow_forwardPlease answer the 4th questionarrow_forwardMECT361 Mechatronics Components and Instrumentation PLEASE GIVE ME THE short answer and wite it by keyword thanksarrow_forward
- I need help answering problems 4, 5, and 6 pertaining to the print provided in the attachment.arrow_forwardHartley Electronics, Inc., in Nashville, producesshort runs of custom airwave scanners for the defense industry.The owner, Janet Hartley, has asked you to reduce inventory byintroducing a kanban system. After several hours of analysis, youdevelop the following data for scanner connectors used in onework cell. How many kanbans do you need for this connector?Daily demand 1,000 connectorsLead time 2 daysSafety stock 12 dayKanban size 500 connectorsarrow_forwardPlease recheck and provide clear and complete step-by-step solution in scanned handwriting or computerized output thank youarrow_forward
- Please give me the answers for this i been looking at this for a hour and my head hurtsarrow_forwardPlease recheck and provide clear and complete step-by-step solution/explanation in scanned handwriting or computerized output thank youarrow_forwardI need help solving these 3 simple parts, if you can not answer all 3 parts then please leave it for another tutor, thank you.arrow_forward
- For the air compressor shown in Figure below, the air enters from a large area and exit from small one, explain why? Instructions for answering this question: The answer to this questian is required as handwritten where you are aiso required to add a Handwritten integrity Statement. Pieose follow the below steps: 1 Write on a blank poper your AUM student ID, full name, course code, section and date 2 Write the following integrity statement and sign: "7 offirm that I have neither given nor received any help on this assessment and that personally compieted it on my own." 3. Write your onswer to the obove question as required 4. Put your Original Civil ID card or AUM ID card on the poper 5 Toke o picture or scan, and uplood Important note: if handwritten document is submitted without the integrity stotement including ID (Civil ID or AUM ID), then the related handwritten question(s) will not be groded.arrow_forwardImportant instruction: This question uses the last three-digit value (L3D) of individual student matrix number. For example, if the matrix number is CD180264 then the L3D value is 264 (since the last three digits is 264). Some data require multiplication of the L3D value, for examAdditional instruction: These questions use the last three-digit value (L3D) of individual student matrix number. Example, if the matrix number is CD180264 then the L3D value is 264 (since the last three digits is 264). Some data require multiplication of the L3D value, for example 10(L3D) means 10 x L3D.ple 10(L3D) means 10 x L3D. subject name isarrow_forwardI need help solving problems 10, 11, and 12 pertaining to the print provided.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY