. Which type of curve is normally produced when plotting the change in the concentration of a specie of some function and the amount of reagent added? A. Titration curve B. Sigmoidal Curve C. Phase Transition curve D. Calibration curve 3. In the dead dear case study, silver diethyldithiocarbamateforms a colored solution when it binds with arsenic, what do we call substance like silver diethyldithiocarbamate? A. Secondary standard reagent B. Precipitating agent C. Chelating agent

. Which type of curve is normally produced when plotting the change in the concentration of a specie of some function and the amount of reagent added? A. Titration curve B. Sigmoidal Curve C. Phase Transition curve D. Calibration curve 3. In the dead dear case study, silver diethyldithiocarbamateforms a colored solution when it binds with arsenic, what do we call substance like silver diethyldithiocarbamate? A. Secondary standard reagent B. Precipitating agent C. Chelating agent

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter10: Potentiometry And Redox Titrations

Section: Chapter Questions

Problem 8P

See similar textbooks

Similar questions

Accurately weigh out about 6g copper(ii) sulfate crystals into a weighing boat. Use the copper(ii) sulfate crystals to make up 250cm3 of standardized copper (ii) sulfate solution Pipette 25cm3 of this solution into a conical flask Add 1.5g potassium iodide and swirl thoroughly Titrate this solution with standard 0.1 moldm-3 Na2S2O3 in a burette. When the iodine color fades, add 1 cm3 starch indicator. Use your titration data below to calculate the percentage by mass of copper in the copper(ii) sulfate crystals.
I'm working on a pre-lab report for chemistry regarding retention factors. The question asks what is the maximum distance the indicator band will travel? Is the indicator band sometimes referred to as the indictor spot?
1. A process where impurity is precipitated along with the desired product. 2. Calculate the gravimetric factor for: Analyte: SiO2 Precipitate: KAlSi3O8
Very pure silver nitrate standard reagent requires standardization with primary standard NaCl or KCl True False A water sample was analyzed for the total hardness through the reaction between the sample and EDTA. The data obtained from the experiment are presented below (MM CaCO3 = 100.0869 g/mol): Table 1. Standrdization of the EDTA solution mass of CaCO3 used 0.5467 g Initial burette reading 8.25 mL Final burette reading 16.65 mL Volume consumed 8.40 mL Table 2. Determination of Hardness of Water Volume of water sample 25.00 mL Initial burette reading 15.00 mL Final burette reading 24.00 mL Volume consumed 9.00 mL 23,469 ppm 22,456 ppm 21,290 ppm 23,990 ppm
An auxiliary competing agent is used in EDTA titrations to slow down the titration. keep some interfering component of the analyte mixture from complexing with the EDTA. speed up the titration. keep the metal ion from precipitating out of the solution.
. 100 ml boiled cooled and filtered water sample takes 9.6 ml of M/50 EDTA in titration. The Permanent hardness of the water sample in terms of ppm of CaCO3 equivalent is
100 mL water sample was subjected to DO analysis using the Winkler method. The initial reading of the titrant (0.025 M Na2SO3) in the buret was 2.51 mL. The endpoint was obtained and the final reading was 7.07 mL. A blank was also titrated and 0.75 mL of the titrant was consumed. Compute for the amount of DO (mg/L) in the sample.
Method used was Volhard Method Sample preparation: 5ml sample diluted in 100 ml. 20ml aliquot was used for analysis. Concentration of AgNO3: 0.0609M Calculate mass of NaCl and % NaCl (w/v)
will the liquid filtrate collecedt after filtering your solid product be acidic.
What conclusion can be derived from the following sentences regarding analytical methods: I. Classical methods (gravimetry and volumetric methods) are no longer useful in analytical chemistry. II. Volumetric methods do not require calibration if a primary standard is used as titrant. III. Instrumental methods are useful with analyte solutions that are less than 1.00 mM. IV. Classical methods yield high precision and accuracy at concentrations greater than 1.00 mM. What conclusion can be derived from the following sentences regarding analytical methods: Two statements are incorrect. All statements are correct. One statement is incorrect. Only one statement is correct. All statements are incorrect.
60 ml of standard hardness containing 1 mg of pure CaCO3 per ml consumed 22 ml of EDTA. 40 ml of water sample consumed 20 ml of EDTA solution using EBT indicator. 40 ml of water sample after boiling, filtering consumed 15 ml of EDTA. Calculate the temporary and permanent hardness of water sample.
The standard addition method is used to analyze a sample of a river water for mercury. Solution A is made by pipetting 5.00 mL of undiluted sample in to a 10 mL volumetric flask and filling to the mark with DI water. Solution B is made by pipetting 5.00 mL of undiluted sample and 3.00 mL of 15.0 ppb of Hg standard into same 10.0 mL volumetric flask and filling to the mark with DI. Solution A and B are analyzed using atomic absorption spectroscopy and give a percent transmittance values of 56 % and 33 % respectively (not blank corrected). A blank has a transmittance of 96%. What is the corrected absorbance of both solution A and B? A. Solution A: 0.123 Solution B: 0.463 B. Solution A: 0.463 Solution B: 0.234 C. Solution A: 0.123 Solution B: 0.234 D. Solution A: 0.234 Solution B: 0.463