5a. What is the number of components for the formulation: "Nitrogen (gas) + Nitrogen (liquid)" CHOICES: A. ONE, B.ZERO, C.TRHEE, D. TWO 5b. Present your working formula for the formulation: "Nitrogen (gas) + Nitrogen (liquid)" 5c. What is the degrees of freedom for the formulation: "Nitrogen (gas) + Nitrogen (liquid)"? CHOICES: A. ONE, B.ZERO, C.TRHEE,

5a. What is the number of components for the formulation: "Nitrogen (gas) + Nitrogen (liquid)" CHOICES: A. ONE, B.ZERO, C.TRHEE, D. TWO 5b. Present your working formula for the formulation: "Nitrogen (gas) + Nitrogen (liquid)" 5c. What is the degrees of freedom for the formulation: "Nitrogen (gas) + Nitrogen (liquid)"? CHOICES: A. ONE, B.ZERO, C.TRHEE,

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter33: Automated Methods Of Analysis

Section: Chapter Questions

Problem 33.8QAP

See similar textbooks

Similar questions

Q1. Dissolved 0.273 grams of pure sodium oxalate (Na,C,O.) in distilled water and added sulfuric acid and titration the solution at 70 ° C by using 42.68 ml of KMNO, solution and has exceeded end point limits by using 1.46 ml of standard oxalic acid (H; C;O.) with 0.1024 N. Calculate the normlity of KMN0.. Note that the molecular weight of sodium oxalate (Na,C,O.) = 134 and its equivalent weight = 67
What is ΔHsys for a reaction at 51.4 °C with ΔSsurr = 749 J mol-1 K-1 ? Express your answer in kJ mol-1 to at least two significant figures.
Given a reaction mixture of 40 mols of ethylebe glycol, 40 mols terephthalic acid, and 1.2 mol benzoic acid, what value of Xn would be expected if complete conversion (p = 1) of limiting factor were completed?
Compare and contrast an anticipatory standard to a reactionary standard by listing and describing some advantages and disadvantages.
Identify the effect of the condition on the indicated parameter. Write increase, decrease, or no effect , and provide an explanation. The test tube used in the determination of the ΔHrxn for nitric acid was still wet with water. [ magnitude of ΔHrxn].
Note: Express % strength with 4 decimal places. For ratio strength, state the volume only% Astelin nasal spray contains 0.1% azelastine hydrochloride and 125 mcg/mL of benzalkonium chloride as a preservative. A container is capable of delivering 200 metered sprays of 0.137 mL each. The percent concentration of benzalkonium chloride in the preparation is _______%, which is equivalent to a ratio strength of 1 in _____ w/v.
4) How would your calculated value of Kup be affected by errors introduced from the following sources? Be specific in your answer. State whether Ksp would be too large, too small, or not affected, and explain why that error would have that effect on Ksp c. Although the KIOs used to standardize the Na2S20s is labeled as 0.0100 M, its actual concentration is somewhat higher than 0.0100 M. d. Extraneous water is introduced from wet filter paper or wet funnels, or by washing the precipitate during the final filtration of Ca(IOs)2.
2 table spoon solution with 10% w/v were diluted to 1 quart with water, what be ratio strength (w/v) the dilution? explain easy
An acid solution containing 2 per cent by mass of NaNO3, and an unknown concentration of HNO3 is used to regenerate a strong acid resin. After sufficient acid had been passed over the resin for equilibrium to attained, analysis showed that 10 per cent of resin sites were occupied by sodium ions. What was the concentration of HNO3 in the solution, if its density were 1,030 kg/cu.m.?
A 18 g of unknown organic sample was dissolve in 756 mL of benzene. The boiling point of benzene was increased by 3.36oC. As the first step of analysis, determine the moecular weight of the unknow sample? Kb of benzene= 2.64oC/m Bb of benzene = 80.09 oC density of benzene = 0.874 g/mL at 25 °C Answer in whole number, no units required.
By the use of Henderson Hasselbalch equation; pH = pKa + log{[acetate ion]/[acetic acid]} 4.5 = 4.75 + log{[0.10 M]/[acetic acid]} -0.25 = log{[0.10 M]/[acetic acid]} [Acetic acid] = 0.10 M/ 10-0.25 [Acetic acid] = 0.10 M/0.56 [Acetic acid] = 0.1786 M Moles of sodium acetate dissolved in 250 mL buffer solution = 0.10 M× (250mL/1000mL) × 1L = 0.025 mol Weight (w) of sodium acetate (purity 100%) dissolved to prepare 250 mL of solution with buffer concentration of 0.10 M is calculate as follow; w100% = 0.025 mol × 82.0343 g/mol = 2.051 g Weight (w) of sodium acetate (purity 99%) is calculate as follow; w99% = 2.051 g× (100/99) = 2.072 g What was the volume of 6.12 M acetic acid HC2H3O2 needed to prepare the 250 mL acetic acid/acetate ion buffer solution required in this part? Show your calculations.
Give only typing answer with explanation and conclusion to all parts 1. What is the value of ΔrG for the reaction MCl2⋅6H2O(s)⇌MCl2(s)+6H2O(g) when the pressure of water vapour is 29.7 mbar ? 2. What is the value of ΔrG∘ when the pressure of water vapour is 1 bar?