A three-component mixture containing AgCl, SiO2, and KBr was provided to you in the lab to isolate. In the first step of the separation, you added deionized water and isolated one component by filtration. In the second step, you added HNO3 to dissolve/extract the second component and separate it by decantation. Which of the three-component (s) was isolated in the first step by filtration as residue? O KBr O AgCl and KBr O Sio2 O AgCl and SIO2 O ABCI O KBr and SIO2

A three-component mixture containing AgCl, SiO2, and KBr was provided to you in the lab to isolate. In the first step of the separation, you added deionized water and isolated one component by filtration. In the second step, you added HNO3 to dissolve/extract the second component and separate it by decantation. Which of the three-component (s) was isolated in the first step by filtration as residue? O KBr O AgCl and KBr O Sio2 O AgCl and SIO2 O ABCI O KBr and SIO2

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter31: Introduction To Analytical Separations

Section: Chapter Questions

Problem 31.19QAP

See similar textbooks

Similar questions

The standard addition method is used to analyze a sample of a river water for mercury. Solution A is made by pipetting 5.00 mL of undiluted sample in to a 10 mL volumetric flask and filling to the mark with DI water. Solution B is made by pipetting 5.00 mL of undiluted sample and 3.00 mL of 15.0 ppb of Hg standard into same 10.0 mL volumetric flask and filling to the mark with DI. Solution A and B are analyzed using atomic absorption spectroscopy and give a percent transmittance values of 56 % and 33 % respectively (not blank corrected). A blank has a transmittance of 96%. What is the corrected absorbance of both solution A and B? A. Solution A: 0.123 Solution B: 0.463 B. Solution A: 0.463 Solution B: 0.234 C. Solution A: 0.123 Solution B: 0.234 D. Solution A: 0.234 Solution B: 0.463
A 25.00mL wastewater sample was analyzed for its Mg2+ content using a standard gravimetric method. the sample was diluted to 3.00L and an 11.00mL aliquot was treated to precipitate magnesium as MgNH4PO4.6H2O using (NH4)2HPO4 as the precipitating agent. the precipitate was then filtered, washed, dried, and ignited resulting in a 0.1325mg Mg2P2O7 residue. How much Mg (in ppm) is present in the original sample
Transfer 3-4 drops or a pinch of the test compound (Aniline) to 3 ml of the solvents, 5% NaOH and 5% HCL Shake the mixture thoroughly. The time required for the solute to dissolve in the solvent should not be more than 2 minutes. Indicate with (+) or (-) if the test compound is soluble or insoluble in the solvent. Is Aniline solube or insolube in 5% NaOH? _______ Is Aniline soluble or insolube in 5% HCL? _______
A scientist wishes to measure the concentration of methyl benzoate in a plant stream by gas chromatography. He prepares a sample of butyl benzoate to use as an internal standard. The results of a preliminary run, which used a solution known to contain 1.37 mg/mL of methyl benzoate (peak A) and 1.51 mg/mL of butyl benzoate (peak B), are shown. The area of peak A is determined to be 3.40×102 and the area of peak B is determined to be 398 measured in arbitrary units by the computer. To measure the sample, 1.00 mL of a standard sample of butyl benzoate containing 2.49 mg/mL is mixed with 1.00 mL of the plant stream material. Analysis of the mixture gave a peak area of 437 for peak A and 415 for peak B. What is the concentration of methyl benzoate in the plant stream?
The concentration of purified OXA-M290 is tested with a BCA assay. Serial dilutions of a bovine serum albumin (BSA) stock solution are prepared, then pipetted into a 96-well plate; each dilution of the BSA standard is tested in triplicate. Then, bicinchoninic acid and Cu2+ ions are added to all of the wells of the plate. After incubating the plate for 1 hour, a microplate reader is used to measure the absorbance of all of the wells in the plate at 560 nm. This generates the following data: BSA conc. (μg/mL), Replicate 1 Absorbance, Replicate 2 Absorbance, Replicate 3 Absorbance 40, 1.360, 1.403, 1.481 20, 0.750, 0.745, 0.810 10, 0.380, 0.344, 0.398 5, 0.198, 0.160, 0.183 2.5, 0.090, 0.100, 0.085 1.25, 0.038, 0.043, 0.051 0.625, 0.024, 0.028, 0.019 Prepare a calibration curve using these data. You can use Excel, R, SPSS or an equivalent graphing software. In this graph, plot absorbance (y-axis) against the concentration of the protein standard (x-axis). Calculate and plot…
To determine the soil distribution coefficient (Kd), 10 g of dry soil is spiked with 100 mg of ring-labeled 14C-atrazine, 10 mL of deionized water is added, and the system is shaken for 24 hours. The aqueous and solid phases are separated, and the solid phase is extracted with 50 mL of methylene chloride while the aqueous phase is extracted with three successive 5 mL portions of methylene chloride. The atrazine concentration in the 50 mL of soil extract is 10 mg/L, and the concentration in the combined 15 mL from the aqueous extractions is 0.4 mg/L. Based on this information, calculate Kd.
. The total cation content of natural water is often determined by exchanging the cations for hydrogen ions on an ion exchange resin. The cations are adsorbed to the resin which releases H+ (1:1 exchange) which can then be titrated with a base. A 25.0 mL sample of a natural water is diluted to 100 mL with distilled water and 2.0 g of a cation-exchange resin was added. After stirring, the mixture was filtered and the solid remaining on the filter paper was washed with three 15.0 mL portions of distilled water. The filtrate and washing required 15.3 mL of 0.0202 M NaOH to reach the equivalence pt. Calculate the number of moles of cation present in 1.00 L of sample.
A STOCK SOLUTION containing 0.1581 g/L K2CrO4 was prepared.In order to make the CALIBRATION STANDARD, 5 ml of the STOCK was transferredinto a 50ml volumetric flask and then diluted with an appropriate solvent.Calculate:(a) The ppm of K2CrO4 in the CALIBRATION STANDARD.(b) The molarity of K2CrO4 in the CALIBRATION STANDARD. (c) Calculate the molar absorptivity of K2CrO4 (at 371.0 nm). Assume that Beer's Law isobeyed over this concentration range.At 371.0 nm, this CALIBRATION STANDARD in a cell of path length 1.00 cm gave a %T of 59.752.
3. Assume that in extraction from water into toulene, analyte A has distribution ratio of 10. A 20 mL portion of an aqueous solution of A is extracted with toulene. Which of thw following procedures will result in most efficient removal of A from the aqueous phase into toulene? (Please show the solution of the correct answer) A. 1 extraction with 20 mL of touleneB. 1 extraction with 40 mL of touleneC. 2 extractions with 20 mL of toulene eachD. 4 extractions with 10 mL of toulene each
A 500ml solution of NaOH was made using 2g of NaOH(s) Three trials of titration were made with using KHP(s) as the acid dissolved with about 25ml of deionized water and 4 drops of phenolphthalein indicator. Slowly adding the NaOH solution until the clear solution had turned pink which would give us our end point and allow us to find the NaOH molarity by equivalence point. Trial 1: - 0.484g of KHP were used - initial volume of buret containing NaOH solution was 0.0 ml - final volume of buret was 23.60ml Trial 2: - 0.485g of KHP were used - initial volume was 0.0ml - final volume was 24.00ml Trial 3: - 0.486g of KHP - initial volume was 0.0ml - final volume was 23.80ml The molarity of NaOH was found by using the moles of KHP(as at equivalence, both solutions are balanced in moles) divided by the total volume of NaOH used to neutralize the solution. Giving us 0.100M for trial 1, 0.099M for trial 2, and 0.100M for trial 3. Make a rough sketch of a titration curve that…
Measure the mass of 0.400g of Co(NO3)2 + 6H2O and dissolve it in 15mL of distilled or deionized water using a clean beaker Then while using a graduated cylinder, measure out 10.0mL of a prepared 0.10-M Na3PO4 soultion. Determine which compound Na3PO4 or Co(NO3)2 *6H2O will be the limliting reagent. Then detrimine the theiretical yeild
The buret was filled with 0.100 M HCl solution. Then was transferred in a 25.0 mL of saturated calcium hydroxide solution (2g of calcium hydroxide per 100 ml of water) in two separate E-flasks. Then 2 drops of phenolphthalein was added to each flask Titration data for the determination of solubility and Ksp of calcium hydroxide: Trial 2: Final Buret reading (ml)-26.10; Initial Buret reading (ml)- 19.80; Temperature (Celcius)- 25 Voume of HCl used: Trial 2- 6.30mL 1. Compute for the moles of H+ used and the moles of OH- present. moles of H+ used = (concentration of HCl) × (volume of HCl used)moles of OH- = moles of H+ used 2. Construct an ICE table for the reaction.3. Calculate the molar solubility (in mol/L) of OH- and Ca2+.4. Determine the solubility of Ca(OH)2 in g/L. (MM of Ca(OH)2 = 74.096 g/mol). 5. Calculate the Ksp of Ca(OH)26. Compute for the percent error of the experimental value for Ksp of Ca(OH)2 with the literature…