A cylindrical part of diameter dis loaded by an axial force P. This causes a stress of PIA, where A = TT14. If the load is known with an uncertainty of ±11 percent, the diameter is known within ±6 percent (tolerances), and the stress that causes failure (strength) is known within ±16 percent, determine the minimum design factor that will guarantee that the part will not fail. The design factor that guarantee the part will not fail is

A cylindrical part of diameter dis loaded by an axial force P. This causes a stress of PIA, where A = TT14. If the load is known with an uncertainty of ±11 percent, the diameter is known within ±6 percent (tolerances), and the stress that causes failure (strength) is known within ±16 percent, determine the minimum design factor that will guarantee that the part will not fail. The design factor that guarantee the part will not fail is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A bar of circular cross-section is subjected to alternating tensile forces varying from a minimum of 200 kN to a maximum of 500 kN. It is to be manufactured of a material with an ultimate tensile strength of 900 MPa and an endurance limit of 700 MPa. Determine the diameter of bar using safety factors of 3.5 related to ultimate tensile strength and 4 related to endurance limit and a stress concentration factor of 1.65 for fatigue load. Use Goodman straight line as basis for design.” [1]
Prob # 1.A round bar made from SAE 1025 low Carbon steel is to support a direct tension load of 50,000 lbs. Using a factor of safety of 4, and assuming that the stress concentration factor, k = 1, What is the suitable standard diameter. Yield stress is 40,000 psi. a. 3 ½ inch b. 2 ¼ inch c. 2 9/16 inch d. 1 ½ inch
The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size. Round your answer to 4 significant figures
Determine the strength of the bedrock granite. Assume you sampled the granite where it was exposed at the surface and ran a series of 4 triaxial compression tests (results given below). Determine the Coloumb coefficient (or friction angle) and the cohesion of the rock given these test results. Either use graph paper to draw Mohr’s circles and a failure envelope to help you determine these values or use the computer to make a plot. Show all your work for credit! Test Confining pressure Axial load at failure 1 4.5 MPa 35.5 MPa 2 9 MPa 50 MPa 3 17 MPa 73 MPa…
A hard-drawn steel wire extension spring has a wire diameter of 4mm, an outside coil diameter of 28 mm, and initial tension of 1200 N is applied to the spring. The spring shows an extension of 85 mm. The approximate number of turns is 25. From the given information: Determine the physical parameters of the spring such as mean diameter, spring index, maximum shear stress, total number of turns, Wahl’s stress factor, free length of the spring, and pitch of the coil
a cylindrical bronze pin of 1mm radius rests on a rotating steel disk at a mean radius of 25mm. the normal load on the pin is 10n. the rotational speed of the disk is 300 rpm and the test last for 10 hrs. the mass losses of the pin and disk are 50 mg and 3 mg respectively. using the data given below, calculate the wear coefficients and wear depths for the bronze pin and steel disk. hardness of bronze = 0.8 Gpa hardness of steel = 2.5 Gpa density of bronze = 8.5 mg/m3 density of steel = 7.8 mg/m3
Calculate the values of Poisson’s ratio of a rod under uniaxial tensile test. Initially it has 15.5 mm diameter and 62 mm gauge length, then it changes to 15.415 mm diameter and 62.102 mm gauge length under a load of 20 kN.a) 0.186 b) 0.242 c) 0.259 d) 0.342
A machine component made of a ductile material is subjected to a variable loading with sigma min =-50 MPa and If the corrected endurance sigma max =50 MPa. limit and the yield strength for the material are sigma_{e} ^ prime =100 MPa and sigma_{y} = 300 MPa, respectively, what is the factor of safety ?
Strength of Material TextbookTopic: Factor of Safety for Stress LimitsProvide step by step solution
A machine member is subjected to fluctuating stress , sigma = sigma_{0} * cos(8pi*t) The endurance limit of the material is 350 MPa. If the factor of safety used in the design is 3.5, what is the maximum allowable value of sigma_{o} ?
A bracket is under a loading condition shown below. It's made from a steel with yield strength (Sy) of 42 ksi and ultimate tensile strength (Sut) of 76 ksi. The diameter is 0.42 in and b = 1.75 in, with the load P fluctuate between 15 lbs (tension) and -5 lbs (compression). Using the modified Goodman or Gerber criterion, determine the fatigue factor of safety based on infinite life. If infinite life is not predicted, estimate the number of cycles to failure. Also check for yielding.
A cylindrical bronze pin rests on a rotating alumina disk at a mean radius of 10 mm. The normal load on the pin is 20 N. The disk's rotational speed is 500 rpm, and the test lasts 5 hours. The pin and disk mass losses are 60 mg and 0 mg (i.e., assuming no mass loss on the alumina disc). Using the material data given below, calculate the wear coefficients for the bronze pin. (Hardness of bronze = 1 GPa, density of bronze = 8.5 Mg/m3; density of alumina = 3.95 Mg/m3).