A cylindrical tank with hemispherical heads is constructed of steel sections that are welded circumferentially (see figure). The tank diameter is 1.5 m, the wall thickness is 23 mm, and the internal pressure is 2 MPa. Determine the maximum shear stress in the cylindrical tank. Welded seams Lütfen birini seçin: a. None b. 16.30 МPа с. 22.67 МPа d. 32.61 MPa e. 62.50 MPa

A cylindrical tank with hemispherical heads is constructed of steel sections that are welded circumferentially (see figure). The tank diameter is 1.5 m, the wall thickness is 23 mm, and the internal pressure is 2 MPa. Determine the maximum shear stress in the cylindrical tank. Welded seams Lütfen birini seçin: a. None b. 16.30 МPа с. 22.67 МPа d. 32.61 MPa e. 62.50 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.13P: : A cylindrical tank with diameter d = 18 in, is subjected to internal gas pressure p = 450 psi. The...

See similar textbooks

Similar questions

A 1/4 in fillet weld is to transmit a total force of 12,000 lb. If the allowable unit stress in shear on the weld is 15,800 psi, the minimum effective length of the weld must be A. 5.4 B 4.9 in C. 4.3 in D 3.9 in.
A beam is supported and loaded as shown in the figure. Data: L = 1000 mm, c = 300 mm, f = 100 mm, D = 100 mm, d = 80 mm. The beam consists of different parts that are welded, and the fillet weld size a is 4 mm. The load q is 2 kN/m, and P = 10 kN. Calculate the maximum stress in the welds.
A circularbeam, 50 mm in diameter, is welded to support using a fillet weld as in the figure. Determinethe size of the weld, if the permissible shear stress is 100 N/mm2.
A double riveted double cover butt joint is made in 12 mm thick plates with 18 mm diameter rivets. Find the efficiency of the joint for a pitch of 80 mm, if σt = 115 MPa ; τ = 80 MPa and σc= 160 MPa.
The allowable stresses for the splice shown are the following: 150 MPa for shear of rivets, 1.35Fy for bearing,0.60Fy for tension and Fy = 250 MPa. Note: rivet holes are 2 mm bigger than the rivet diameter and the middleplate is 20 mm thick. Find the diameter of the rivets so that the joint capacity due to shear approximately equal to the bearingcapacity.a. 25.4 mm c. 28.65 mmb. 30.79 mm d. 36.97 mm Find the maximum safe value of P without exceeding the allowable shearing stressa. 773.6 kN c. 938.3 kNb. 878.1 kN d. 848.2 kN Find the maximum safe value of P without exceeding the allowable tensile stress.a. 579.3 kN c. 716.1 kNb. 495.5 kN d. 692.5 kN
A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?.
An AISI 1035 CD steel tube has an OD = 45 mm and a wall thickness of 5 mm. What maximum external pressure can this tube withstand if the largest principal normal stress is not to exceed 80 % of the minimum yield strength of the material? Assume ?? = 0.
A welded joint, as shown in figure below, is subjected to an eccentric load of 2500 N. Find thesize of the weld, if the maximum shear stress in the weld is not to exceed 50 N/mm2
A spherical tank of diameter 48 in. and wall thickness 1.75 in. contains compressed air at a pressure of 2200 psi. The tank is constructed of two hemispheres joined by a welded seam (see figure). (a) What is the tensile load/ (lb per in. of length of weld) carried by the weld? (b) What is the maximum shear stress rm2Xin the wall of the tank? (c) What is the maximum normal strain e in the wall? (For steel, assume E = 30 X 10 psi and v = 0.29.)
A PL 300 x 20 mm is to be connected to two plates of the same material with half the thickness by 25 mm Ø rivets as shown in the figure. The rivet holes have a diameter 2 mm larger than the rivet diameter. The plate is A36 steel with Fy = 250 MPa, allowable tensile stress of 0.60Fy and allowable bearing stress of 1.35Fy . The rivets are A502, Grade 2, hot-driven rivets with allowable shear stress of 150 MPa. DEtermine the max. load in kN that can be applied to the connection without exceeding the allowable shear stress in the rivet Determine the max. load in kN that can be applied to the connection without exceeding the allowable bearing stress between the plates and the rivets DEtermine the max. load in kN that can be applied to the connection without exceeding the allowable tensile strength of the plates
A cylindrical pressure tank is fabricated by butt-welding 19 mm-thick plate with spiral seam shown below. The pressure in the tank is 2.76 MPa, and an axial load of 133.5 KN is applied to the end of the tank through a rigid bearing plate. Determine the normal stress and shearing stress perpendicular to the weld.
appropriate length of the weld joint shown in the figure if the force is equal to (60000lb) and the operating stress value is (60ksi) and the size of the weld is (1/4in).