Q2/A horizontal pipe carries cooling water at 10°C for athermal power plant. what is the pressure in thepipe at L = 2000 m? The head loss in the pipe is0.02(L/D)V?%3D+ Ecvation = 1C0 mh, =0.02-Dg80 m%3DD=02m2gDatumwhere L is the length of the pipe from the reservoir tothe point in question,V is the mean velocity in the pipe, andD is the diameter of the pipe.The pipe diameter is 20 cm and the rate of flow is 0.06m/s,Q=0.06 msElevation 20 mL=2000 m-

Answered: Image /qna-images/answer/a7fcb7a7-c832-42d5-a21c-054a72b8db5b.jpg

A horizontal pipe carries cooling water at 10°C for a thermal power plant. what is the pressure in the pipe at L = 2000 m? The head loss in the pipe is 0.02(L/D)V² + Eevation = 1C0 m =0 Dg %3D 80 m D=02m 2g DatumL where L is the length of the pipe from the reservoir to the point in question, Q=0.06 ms El:vation = 20 m L=2000 m- V is the mean velocity in the pipe, and D is the diameter of the pipe. The pipe diameter is 20 cm and the rate of flow is 0.06 m/s,

A horizontal pipe carries cooling water at 10°C for a thermal power plant. what is the pressure in the pipe at L = 2000 m? The head loss in the pipe is 0.02(L/D)V² + Eevation = 1C0 m =0 Dg %3D 80 m D=02m 2g DatumL where L is the length of the pipe from the reservoir to the point in question, Q=0.06 ms El:vation = 20 m L=2000 m- V is the mean velocity in the pipe, and D is the diameter of the pipe. The pipe diameter is 20 cm and the rate of flow is 0.06 m/s,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The system in Fig. consists of 1200 m of 5 cm castiron pipe, two 45° and four 90° flanged long-radius elbows,a fully open flanged globe valve, and a sharp exit into areservoir. If the elevation at point 1 is 400 m, what gagethe pressure is required at point 1 to deliver 0.005 m3/s of waterat 20°C into the reservoir?
Water (@ 45°C) is flowing in a horizontal pipe with an increasing cross-sectional area. The measured pressure drop in the piper is 4.1 psia. If the cross-sectional area at the exit of the pipe is 2x the cross-sectional area at the entrance, what is the V of the water as it enters the pipe? Assume that frictional losses are negligible .
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
HW Question : The tank-pipe system is to deliver at least 12.5 m3/h of water at 20°C to the reservoir. What is the maximum roughness height ε allowable for the pipe? Neglect minor losses.
A pump takes water at 60 F from a largereservoir and delivers it to the bottom of anopen elevated tank 25 ft above the reservoirsurface through a 3-in ID pipe. The inlet tothe pump is located 10 ft below the watersurface, and the water level in the tank isconstant at 160 ft above the reservoir surface.The pump delivers 150 gal/min. If the total loss of energy due to friction in the pipingsystem is 35 ft-lb, per 1bm of fluid, calculatethe horsepower required to do the pumping.The pump-motor set has an efficiency of 55%.
1. in a section of horizontal piper with a diameter of 3cm the pressure is 5.21 kpa and water is flowing with a speed of 1.50m/s. the pipe narrows to 2.50cm. what is the pressure in the narrower region if water behaves like an ideal fluid of sensity 1000kg/m3 2. tensile stress a. the ratio of elasic modules to strain b. the applied force per crosssectional area c. the ratio of change in length to the orig length d. the strain per unit legth e. the same as force
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa (indicate the sign if negative) Decimal Places required in the final answer: 3
Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
The tank–pipe system of Fig. is to deliver at least11 m3/h of water at 20°C to the reservoir. What is themaximum roughness height ε allowable for the pipe?
Helium (Table A.4) enters a 5-cm-diameter pipe at p1 =550 kPa, V1 = 312 m/s, and T1 = 40 °C. The friction factoris 0.025. If the flow is choked, determine (a) the length ofthe duct and (b) the exit pressure.
Water at 20°C is to be pumped through 2000 ft of pipe fromreservoir 1 to 2 at a rate of 3 ft3/s, as shown in Fig. P6.62.If the pipe is cast iron of diameter 6 in and the pump is75 percent efficient, what horsepower pump is needed?