according to Maximum Shear strain energy theory ,Calculate the factor of safety of the shaft When it is subjected to an end thrust producing stress of 90 MPa and the maximum shearing stress on the surface arising from torsion is 60 MPa.The yield point of the material in simple tension was found to be 300 MPa.

according to Maximum Shear strain energy theory ,Calculate the factor of safety of the shaft When it is subjected to an end thrust producing stress of 90 MPa and the maximum shearing stress on the surface arising from torsion is 60 MPa.The yield point of the material in simple tension was found to be 300 MPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.10P: What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm,...

See similar textbooks

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
according to Maximum Shear Stress theory ,Calculate the factor of safety of the shaft When it is subjected to an end thrust producing stress of 90 MPa and the maximum shearing stress on the surface arising from torsion is 60 MPa.The yield point of the material in simple tension was found to be 300 MPa.
A Steel shaft is subjected to an end thrust producing a stress of 90 MPa and the minimum shearing stress on the surface arising from torsion is 60 MPa .The yield point stress of the material in simple tension was found to be 300 MPa. calculate the factor of safety of the shaft according to the following theory 1)maximum shear stress theory
Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm and thickness 2 mm, subjected to a torque of 92.7 N-m.
The internal loadings at a critical section along the steel drive shaft of a ship are calculated to be a torque of 2300 lb # ft, a bending moment of 1500 lb # ft, and an axial thrust of 2500 lb. If the yield points for tension and shear are sY = 100 ksi and tY = 50 ksi, respectively, determine the required diameter ofthe shaft using the maximum shear stress theory.
Two solid shafts, 50 mm in diameter, are connected by a flange coupling with six bolts and a pitch circle diameter of 95 mm. If the maximum shear stress in the shaft due to a torque is to be the same as the shear stress in the bolts, calculate a suitable bolt diameter. If the maximum working shear stress is limited to 55 MPa, what maximum power will be transmitted by the coupling at 700 r/min?
A shaft is to be fitted with a flanged coupling having 8 bolts on a circle of diameter 150 mm. The shaft may be subjected to either a direct tensile load of 400 kN or a twisting moment of 18 kN·m. If the maximum direct and shearing stresses permissible in the bolt material are 125 MPa and 55 MPa respectively. Find the minimum diameter of the bolt required. Assume that each bolt takes an equal share of the load or torque.
Problem 1: A circular shaft with a diameter of 100 mm and a length of 2 meters is subjected to a torsional moment of 500 Nm. The shaft is made of a material with a shear modulus of 80 GPa. Determine the maximum shear stress and the angle of twist along the length of the shaft. Problem 2: A solid circular shaft of length 3 meters is made of a material with a shear modulus of 60 GPa. The shaft has a diameter of 80 mm and is subjected to a torque of 600 Nm. Due to manufacturing constraints, the maximum allowable shear stress for the material is 60 MPa. Determine if the shaft design is safe and, if not, suggest an alternative design to meet the given constraints.
A shaft is to be fitted with a flanged coupling having 8 bolts on a circle of diameter 150mm. the shaft may be subjected to either a direct tensile load of 400kN or a twisting moment of 18kN-m. if the maximum direct and shearing stress permissible in the bolt material are 125MPa and 55MPa respectively, find the minimum diameter of the bolt required.
A turbine developing 15,000 Hp turns the shaft at 300 rpm. The propeller attached to this shaft develops a thrust of 150,000 lbs. A hollow steel shaft having an outside diameter of 14 in is to be used. A. Determine the inside diameter of the shaft if the maximum shearing stress based on the torsion alone is not to exceed 7500 psi. B. Determine the percentage savings in weight if a solid shaft is to be replaced with the hollow steel shaf