Air flows upward at a volumetric flow rate of 0.045 m3/s through an inclined pipe whose diameter is reduced through a reducer. The differential height between fluid levels of the two arms of a water manometer attached across the reducer is to be determined. The diameter at cross-section 1 is 0.06 m, and 0.04 m at cross-section 2. The atmospheric pressure is 110 kPa, and the air temp

Q: A 90-cm ID pipeline (f = 0.020) of length 3000 m connects a reservoir whose water surface elevation…

A:

Q: Q1/Water at 20'C is being pumped from a storage tank to an elevated second tank at a rate of 0.5…

A: Given data as per question volume flow rate =0.5 m3/s Elevation of the surface of storage tank =110…

Q: 1. A pipe 100 mm bore diameter carries oil of density 900 kg/m3 at a rate of 4 kg/s. The pipe…

A:

Q: 3\ Water flows through a horizontal pipe at a rate of 0.01 m /s. The pipe consists of two sections…

A:

Q: 4. The impeller of a centrifugal blower has a radius of 18 cm and a blade width of 6.1 cm at the…

A:

Q: Consider the incompressible, frictionless flow of a fluid in horizontal piping. The pressure and…

A: given data- P1 = 150 kPa v1 = 1.25 m/s P2 = 140 kPa Density = 700 kg/m3 to determine- v2  (velocity…

Q: eter is A petroleum product is pumped at a rate of 2.32 x 10'm/s from a reservoir under atniospheric…

A: Given: The flow rate, Q = 2.32 x 10-3 m^3/s The height to be pumped, hd = 177 cm = 1.77 m The pump…

Q: The impeller of a centrifugal blower has a radius of 15 cm and a blade width of 6.1 cm at the…

A: Given: Inlet radius is r1=0.15 m. Inlet blade width is b1=0.061 m. Outlet radius is r2=0.3 m. Outlet…

Q: water flows through a horizontal venturyi meter whose inlet diameter is 33 cm. and throat diameter…

A:

Q: Air at 105 kPa and 37° C flows upward through a 6-cm-diameter inclined duct at a rate of 65 L/s. The…

A: Consider the diagram shown below for the venturimeter.

Q: A horizontal Venturimeter with inlet and throat diameters 300 mm and 150 mm respectively is used to…

A:

Q: Air flows steadily from a tank pressurized to 3kPa through a pipe of diameter D = 0.03 m and finally…

A: Given              Pressure, P = 3 kPa  Nozzle diameter, d = 0.01 m   Specific weight, w = 12 N/m3…

Q: 1.)  A Pelton wheel with a needle-controlled nozzle develops 1 050 kW against a gross  head of 300…

A:

Q: Water enters a tank of diameter DT steadily at a mass flow rate of m . in. An orifice at the bottom…

A: Consider the diagram shown below for the given system. Let us consider that the maximum height of…

Q: Two pipes, one of internal diameter (I.D.) 0.5 m and the other of I.D. 1 m, are connected as shown…

A:

Q: A liquid with a density of 0.8 [g/ml] flows through a tube with an inner diameter of 50 [mm].  There…

A:

Q: Water flow steadily at the rate of 10 gpm through a horizontal tee and discharges to the atmosphere.…

A:

Q: Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast…

A: The properties of water at 15 degrees Celsius are: The surface roughness of the cast iron pipe is…

Q: Q1/Water at 20°C is being pumped from a storage tank to an elevated second tank at a rate of 0.5…

A: Given data as  Volume flow rate (Q)= 0.5 m3/s Elevation of storage tank = 110 m Elevation of second…

Q: Heavy oil is flows in a 40 cm diameter cast iron pipe f= 0.044. If the head loss due to pipe…

A:

Q: In a pipe conveying steady flow of incompressible fluid, what factor determines the magnitude of…

A: To find : what factor determines the magnitude of flow velocity In a pipe conveying steady flow of…

Q: In a pumping system handling water, the level in the suction tank is 3.2m below the pump shaft…

A:

Q: A clothes dryer discharges air at 1 atm and 120°F at a rate of 1.2 ft3/s when its 5-in-diameter,…

A: Given Discharged air temperature = 120 F Discharged air pressure = 1 atm Diameter of the pipe = 5 in…

Q: Assume a mass flow rate of 13 kilogram-force per second. The fluid is moving through insulated pipe…

A:

Q: Rank in order, from highest to lowest, the liquid heights h1 to h4 in tubes 1 to 4. The airflow is…

A: The height of liquid in tube increases with the increase in velocity, since higher the velocity,…

Q: Water enters a hydraulic turbine through a 30-cmdiameter pipe at a rate of 0.6 m3/s and exits…

A:

Q: Water drains from a pressurized tank (50 kPa gage) with a height of 200 m through a 200 m horizontal…

A: Given: The pressure, Pg = 50 kPa The height, h = 200 m the flow rate, Q = 0.0371 m^3/s The length o…

Q: At a water treatment plant, water (68°F) flows from tank 1 to tank 2 at a rate of 0.60 cfs through a…

A: Note:- From Colebrook equation(Turbulent flow):-…

Q: Water flow steadily at the rate of 10 gpm through a horizontal tee and discharges to the atmosphere.…

A:

Q: A 6cm diameter horizontal water pipe expands to a 10cm diameter pipe. The average velocity and…

A:

Q: An orifice with a 1.8-in-diameter opening is used to measure the mass flow rate of water at 60°F (?…

A: B =d/D B= 1.8/4 = 0.45

Q: A pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water discharges to…

A: In order to proceed with the given problem, the following assumptions need to be taken into…

Q: Water flows through a horizontal pipe at a rate of 0.01 m /s. The pipe consists of two sections of…

A:

Q: water of mass density of 998 kg/m^3 and viscosity of 1.002 x 10^-3 kg/m-s, through a 600 mm diameter…

A:

Q: Water flows through a horizontal pipe at a rate of 0.01 m/s. The pipe consists of two sections of…

A:

Q: ME 3022 - HW 19 1. (More practice from Monday) A 90° elbow in a horizontal pipe is used to direct a…

A: Given: Flow rate, m˙=30 kg/sD=10 cm=0.1 mMomentum-flux correction factor, β=1.03 Mass flow rate is…

Q: The power carried by fluid into the control volume, (W). Head carried by fluid out the control…

A: Total energy available at entry per unit volume is given by the the bernoulli's equation  P₁ +…

Q: A 20 hp pump with a suction from an open reservoir (10 m above the pump) has a flow rate of 125…

A:

Q: A centrifugal pump is required to deliver 50 liters of water per second to a height or 30 m through…

A: Discharge, Q= 50 liters of water per second= 0.050 m3/s Height, h= 30 m Length of the pipe, L= 100 m…

Q: Two water reservoirs A and B are connected to each other through a 40-m-long, 2-cm-diameter cast…

A: In order to proceed with the problem following assumptions are taken into consideration. The flow…

Q: Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast…

A: Given: Discharge is Q=18 L/s=0.4 m3/s, height of the reservoir is h=30m,length of the first pipe…

Q: QI- Water flows at a rate of 0.040 m/s in a 0.12-m-diameter pipe that contains a sudden contraction…

A: In fluid mechanics, there are two types of flow laminar and turbulent. The flow which doesn't have…

Q: Air at 105 kPa flows upward through a 6-cm-diameter inclined duct at a rate of 65 L/s. The duct…

A: Given data  P1 = 105 kPa d1 = 6 cm = 0.06 m Q = 65 lps = 0.065 m3/s d2 = 4 cm = 0.04 m (z2 - z1) =…

Q: - Air at 105 kPa and 37°C flows upward through a 6-cm-diameter inclined duct at a rate of Q (L/s).…

A:

Q: Q3. Water enters a tank of diameter DT steadily at a mass flow rate of min. An orifice at the bottom…

A: Drawing the figure as shown below -   In sections 1 & 2 the tank is open to atmosphere and…

Q: Water enters a tank of diameter D7 steadily at a mass flow rate of m: An orifice at the bottom with…

A:

Q: Water at 70°F flows by gravity from a large reservoir at a high elevation to a smaller one through a…

A: The density of the water is 62.428 lbm/ft3. The dynamic viscosity of the water is 1.307×10-3…

Q: Air speed in a duct is measured using a Pitot static tube where the differential pressure reading is…

A: Given:P=0.05 KPaρ=1.041 Kg/m3

Q: 3.82 JP-4 fuel (SG = 0.77) flows through the Venturi meter shown in Fig. P3.82 with a velocity of 15…

A: Calculate the velocity using continuity equation, A1V1=A2V2 π4d12V1=π4d22V262×15=42×V2V2=33.75 ft/s

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.