An AGE run was set at 100V for 30 min, where 3 ul of the ladder (100 ng/ul) was loaded into the gel, while 10 ul of the DNA samples plus an appropriate amount of 6x loading buffer were added into the gel. Shown below is the AGE profile and the needed marker details where M is the MW marker while numbers 1-4 indicate the lanes with the DNA samples: м 1 M 2 3 4 ng/0.5 µg bp 20 5000 20 4000 40 3000 20 2000 20 1000 60 500 20 100 Determine the amount of the total DNA ladder added in the gel in terms of ug

An AGE run was set at 100V for 30 min, where 3 ul of the ladder (100 ng/ul) was loaded into the gel, while 10 ul of the DNA samples plus an appropriate amount of 6x loading buffer were added into the gel. Shown below is the AGE profile and the needed marker details where M is the MW marker while numbers 1-4 indicate the lanes with the DNA samples: м 1 M 2 3 4 ng/0.5 µg bp 20 5000 20 4000 40 3000 20 2000 20 1000 60 500 20 100 Determine the amount of the total DNA ladder added in the gel in terms of ug

Human Heredity: Principles and Issues (MindTap Course List)

11th Edition

ISBN:9781305251052

Author:Michael Cummings

Publisher:Michael Cummings

Chapter3: Transmission Of Genes From Generation To Generation

Section3.7: Mendelian Inheritance In Humans

Problem 2EG: For most cases, a p value of 0.05 is used to determine whether results fit expected values. Is this...

See similar textbooks

Similar questions

What are the x and y values that you have input in the excel? I thought the x would be from the concentation and the y is from the A595 of sample minus A595 of blank but the linear equation that shows up in mine is different. It's y = 0.0443x + 0.0148.
An AGE run was set at 100V for 30 min. The 3 ul of the ladder was loaded into the gel, while 10 ul of the DNA samples plus an appropriate amount of 6x loading buffer were added into the gel. Find the amount of the 6x loading buffer added to 10 ul DNA samples in order to make the samples sink in the gel? Tip. From 6x final conc of the loading buffer should be 1x and answer shoud be in ul
At the station there is a 2 mL microcentrifuge tube containing sheep blood and 3 tubes containing the following solutions: 0 mM, 300 mM, 600 mM of sucrose. The tubes are randomly labelled A, B, C. 2 mL of each solution were transferred to a different microcentrifuge tube, 20 ul of blood were then added to each tube, and they were mixed well by inverting the tube for multiple times. They were observed and it was determined whether the solution in each tube was hypotonic (Yes or No) relative to the blood cells. In addition, the solutions were diluted with water to help you determine which solution is which sucrose concentration. What sucrose concentration corresponds with each tube? Tube Hypotonic (Yes/No) Hypotonic after 1:1 dilution with water (Yes/No) Most likely Sucrose concentration (mM) A No Yes B Yes Yes C No No
Which precise standards are you going to apply in order to identify your unknown? Make sure your RFP can be clearly distinguished from the other two using the criteria. lab intro attcehd if needed:
I have a 1.270 ug/uL dna stock, how would you dilute this to 50ng/nL in a single dilution step? show the exact process including the volume of water. Indicate if you would use p20,p200,p1000 for each reagant added. you can choose a total volume but cannot be less than 3 uL or exceed 1000uL. Thank you!!
A 100ml dsDNA solution prepared via 1:20 dilution was taken for spectrometry analysis. The A260 and A320 values obtained were 0.4210 and 0.1210 respectively. The total DNA yield of the solution in micrograms would be 40000 300 30000 400
Amazingly, the sensitivity of STR profiling requires only ___________ DNA-bearing cells to obtain an STR profile.
DNA samples were then run in agarose gel electrophoresis against a molecular standard of 100 bp and 1Kb Ladder. The figure is analyzed and labelled manually and recorded with the used product ladder information. Figure 2A is labeled with corresponding lane numbers and with M1 and M2 as markers used. Write an interpretation of the documented gelresult (Figure 2). Note: Agarose gel of isolated DNA (A) from plant (lanes 1 & 2), chicken (lanes 3 & 4), and E. coli (lanes 5 & 6) with Vivantis* product information of 100bp (B) and 1kb ladders (C).
A 10-2 is performed on a culture of bacteria in order to perform viable plate counts. From the dilution, *0.1 mL* of solution is plated on solid media, and 61 colonies of bacteria grow on the plate. Assuming each colony came from a single bacterium, how many bacteria are in a single mL of the original culture?
You have performed a serial dilution of an unknown sample and counted 73 CFU on a countable plate that was marked at 10^-4 dilution and you used 0.1 mL to inoculate the plate. What is the population of the original sample?
Horizontal sequence :RIVL Vertical sequence:FMK Scoring rules: g/o = -3, g/e = -1, match or mismatch - from PAM250 substitution matrix below. SW algorithm. 1. Complete the scoring matrix. Scoring matrix with PAM250 scores: R I V L F M K 2. Set up, initialize and complete the SW matrix. 3. Retrace, align and score alignment(s). Use the arrows and circles for the matrix and path(s). R I V L F M K Align and score all optimal alignments here. PLZ the arrows and circles for the matrix and path(s) AND SHOW ALL possible Alignment Here the following points…
If the purity of DNA sample is below 1.8 A260/A280, where did the protein contamination come from?