Atomic Density Calculate the density of body-centered cubic iron and compare it to the density of face-centered cubic iron. BCC Fe exists at temperatures below 1183 K and has a lattice parameter of 0.287 nm. FCC Fe exists between 1183 K and 1673 K and has a lattice parameter of 0.354 nm. BCC PFe g/cm FCC PFe g/cm3 Compare your results for the BCC iron to the actual measured value given in Callister. 7.87g/cm. How can you explain the discrepancy in terms of lattice defects? PFe

Atomic Density Calculate the density of body-centered cubic iron and compare it to the density of face-centered cubic iron. BCC Fe exists at temperatures below 1183 K and has a lattice parameter of 0.287 nm. FCC Fe exists between 1183 K and 1673 K and has a lattice parameter of 0.354 nm. BCC PFe g/cm FCC PFe g/cm3 Compare your results for the BCC iron to the actual measured value given in Callister. 7.87g/cm. How can you explain the discrepancy in terms of lattice defects? PFe

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter21: Structure And Bonding In Solids

Section: Chapter Questions

Problem 42P

See similar textbooks

Similar questions

Can nitrogen fit into the octahedral interstitial site in BCC iron? Justify your answer by calculation. Atomic radius of nitrogen is 0.071nm and lattice parameter of BCC iron is 0.2866 nm
A device to understand how iron behaves at high temperatureswe want to design. This device (with 1% accuracy) allows the change in volume (heating) of a 1cm 3 iron cube.the resulting polymorphic transformation) must be able to feel. HMK structure in iron 911 0 C and latticeparameter 0.2863 nm. At 913 0 C, it has YMK structure and its lattice parameter is 0.3591 nm. Of measuring instrumentDetermine the accuracy tolerance it needs (i.e. at least how many cm 3 to detect a changemust). It is necessary to use at least 6 digits after the comma in this question. Hint: YMK first andFor HMK, the volume of an atom is found and then, using the number of atoms in each structure, the ironThe question can be started by finding the different volumes.
The addition of dimethylglyoxime, H2C4H602N2, to a solution containing nickel(Il) ion gives rise to a precipitate: Nickel dimethylglyoxime is a bulky precipitate that is inconvenient to manipulate in amounts greater than 135 mg. The amount of nickel in a type of permanent-magnet alloy ranges between 22% and 38%. Calculate the sample size that should not be exceeded when analyzing these alloys for nickel.
Fluorite (CaF2) has a face centered cubic structure, space group 225, with network parameter equal to 5.45 Å), with four CaF2 units per cell unitary (Ca+ at site 4a(0,0,0) and F- at site 8c(1/4.1/4.1/4 and 3/4.3/4.3/4) + face centered cubic lattice translations for both ions). a) Get a simplified expression for the structure factor F(hkl) of fluorite. (b) What condition must be fulfilled by the Miller indices h,k,l in such a way that F(hkl) ≠ 0?
show that the atomic packing factor for BCC is 0.68 and forHCP is 0.74.
Determine the repeat distance, linear density, and packing fraction for BCC lithium, which has a lattice parameter of 0.35089 nm, in the [100] , [110] [111] , and directions. Which of these directions is close packed?
GRAVIMETRIC ANALYSIS The addition of dimethylglyoxime, H2C4H602N2, to a solution containing nickel(Il) ion gives rise to a precipitate: Nickel dimethylglyoxime is a bulky precipitate that is inconvenient to manipulate in amounts greater than 135 mg. The amount of nickel in a type of permanent-magnet alloy ranges between 22% and 38%. Calculate the sample size that should not be exceeded when analyzing these alloys for a nickel.
(d) By using the data provided below, calculate the PillingBedworth ratio for the nickel (Ni) – nickel oxide (NiO) system and determine whether NiO is protective against corrosion. Atomic mass of nickel = 58.7 g.mol-1 Density of nickel = 8.91 Mg.m-3 Molecular mass of nickel oxide = 74.7 g.mol-1 Density of nickel oxide = 6.67 Mg.m-3 (e) A stainless steel pressure vessel that has fracture toughness, K1C, of 197 MN.m-3/2 is going to be exposed to a stress of 398 MN.m-2 . By using this information explain how designers can determine the thickness of the vessel so that catastrophic failure can be avoided.
I) Diamond crystallises in a face-centred cubic structure with a = 3.5625 Å. Calculate the d-spacing and peak position of the first allowed peak (i.e. the peak with the lowest hkl value that meets the selection rules) using a wavelength of 0.71073 Å. II) A solvothermal synthesis gave rise to a mixture of two crystalline phases: one phase consists of 50-65 μm octahedral crystallites while the other phase consists of 150-180 μm hexagonal plates. Identify a separation technique that would likely be effective in separating these materials.
Assuming that the density of silica gel is 2.65 g cm-3 and that the silica particle are spherical with an average radius of 5 x 10-6 cm, calculate the estimated surface area Sest. Why is there such a large difference between S and Sest?
Suppose you have collected the X-ray powder diffraction pattern of tetragonal BaTiO3 at roomtemperature using copper radiation (λ=1.54 Å) and identified the lattice planes corresponding to thepeaks at each 2θ positions, as shown in the table below. 2θ (°) (hkl) Intensity (%)22.05 (001) 12.022.28 (100) 25.031.45 (101) 100.031.65 (110) 100.038.82 (111) 46.044.86 (002) 12.045.39 (200) 37.050.60 (102) 6.050.98 (201) 8.051.3 (210) 7.056.01 (112) 15.056.3 (211) 12.065.75 (202) 35.0 Determine:a) the d-spacing of the four most intense reflections; b) the lattice parameters a, b and c of the unit cell.
For dissolution of dopant ZrO2 into the host lattice of Y2O3, does the following defect reaction satisfy the requirements of mass conservation, charge neutrality, and site balance (stoichiometry)? 2 ZrO2 -(Y2O3) -> 2 ZrY + 3 Ox + ½ O2 (g) + 2eʹ