Belt tension along its entire length around two pulleys is 200 N. In the transmission of power, the tension increases by 20 N at the tight end. Furthermore, the net torque is equal to the formula in N.m unit (5 + 0.005 F1 -0.001 F2) ; and the diameter ratio (D1 of driver / D2 of driven) is equal to 1.25, and the central distance between the pulleys is 0.6 m. Additionally, the driven pulley rotates 4515 times in two minutes. Calculate the following parameters : F1, F2 , net torture, length of belt, The Time that takes frome the belt to complete one full revolution for the whole system starting from a certain point

Belt tension along its entire length around two pulleys is 200 N. In the transmission of power, the tension increases by 20 N at the tight end. Furthermore, the net torque is equal to the formula in N.m unit (5 + 0.005 F1 -0.001 F2) ; and the diameter ratio (D1 of driver / D2 of driven) is equal to 1.25, and the central distance between the pulleys is 0.6 m. Additionally, the driven pulley rotates 4515 times in two minutes. Calculate the following parameters : F1, F2 , net torture, length of belt, The Time that takes frome the belt to complete one full revolution for the whole system starting from a certain point

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem: A pump is driven by an electric motor through an open type flat belt drive. Determine the belt specificationsfor the following data.Motor pulley diameter= 400 mmPump pulley diameter = 800 mmCoefficient of friction for motor pulley = 0.30Coefficient of friction for pump pulley = 0.35Center distance between the pulleys=2000 mmRotational speed of the motor=2000 rpmPower transmission = 40kWdensity of belt material = 1000 kg/m3 width of the belt=240mmthickness of the belt = 5mm
Prob # 8. If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0 to 1500 rpm in 3 seconds. Calculate the heat generated for each engagement if clutch starting torque is 10 in-lb. a. 50 Btu b. 50 Btu c. 30.50 Btu d. 51.50 Btu
Prob # 9. Find the horsepower transmitted by a pair of friction wheels, the diameter of driving wheel is 10 inches, and it revolves at 200 rpm. The width of the wheel is 2 inches. The force per inch width of face is 150 pound and the coefficient of friction is 0.20. a. 96 hp b. 23 hp c. 1.2 hp d. 1.6 hp
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.
PROBLEM The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V-belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=900N), coefficient of friction ų=0.3 4- the speed of large pulley.
The turning moment diagram for a multi cylinder engine has been drawn toa scale of 1 mm = 4500 N -m vertically and 1 mm = 2. 4 ͦ horizontally. Theintercepted areas between output torque curve and mean resistance lineabove and below the mean taken in order from one end are 342, 23, 245,303, 115, 232, 227, 164 ??2, when the engine is running at 150 rpm. Ifthe mass of the flywheel is 1000 kg and the total fluctuation of speed doesnot exceed 3% of the mean speed, find the minimum value of the radius ofgyration.
In an open flat belt drive, a pulley of 800 mm diameter runs at 300 r.p.m. The coefficient of friction between the belt and the pulley is 0.25, the angle of lap is 170° and the maximum tension in the belt is 2000 N. The power transmitted is: 10.5 kW 9.4 kW 8.9 kW 7.6 kW None of the mentioned 13.1 kW
Two pulleys, one 425mm diameter and the other 210mm diameter are one parallel shaft 2m apart and are connected by a crossed flat belt. Find the length of the belt required and the angle of conduct between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 200 rev/min, if the maximum permissible tension in the belt is 1 kN, and the coefficient of friction between the belt and pulley is 0.3?
The 10 N cylinder moves in a friction tube. Spring constants are k1 = 150 N / m and k2 = 200 N / m. When the system is at rest, d = 0.5 m. The system rotates around a fixed z-axis. In the case where d = 0.12 m, what is the coefficient of friction for the cylinder to have a constant velocity of 9.825 m / s?
The diameter of the pulley on the compressor shaft must not be greater than 1.2 metre while the centre distance between the pulleys is limited to 1.85 metre. A compressor, requiring 95000W is to run at about 500 r.p.m. The drive is by V- belts from an electric motor running at 1500 r.p.m. The belt speed should not exceed 1500 m/min. The coefficient of friction between the belt and the pulley is 0.3. Determine the number of V-belts required to transmit the power if each belt has a crosssectional area of 3 cm2, density 1100 kg/m3 and an allowable tensile stress of 3 MPa. The groove angle of the pulley is 50°. Calculate also the length required of each belt.
.A steam engine develops power at mean torque of 18,000 N-m and velocity of 9 m/s. The mean diameter of the flywheel rim is 1.3 meters. The coefficient of fluctuation of speed is 0.03 and the coefficient of fluctuation of energy is 0.21. Determine the thickness of the rim in mm if the width of the rim is twice of its thickness. Assume density of rim material as 7250 kg/m3.