Answered: Calculate the concentration of Cu in…

Calculate the concentration of Cu in the sample by calibration curve using the following data Concentration (ppm) Absorbance 2 0.150 4 0.301 6 0.455 8 0.598 10 0.745 sample 0.360

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter24: Introduction To Spectrochemical Methods

Section: Chapter Questions

Problem 24.16QAP

See similar textbooks

Related questions

Q: The glucose content of samples can be determined using Nelson’s test. The equation of the line for…

A: A numerical problem based on calibration curve that is to be accomplished.

Q: The following Absorbance vs concentration of nitrite graph is obtained for a set of data: y =…

A: The given graph depicts absorbance VS concentration relation with absorbance on y-axis and…

Q: Chemistry Given the following spectrophotometric data, what is the concentration of the sample?…

Q: 100 ml boiled cooled and filtered water sample takes 9.6 ml of M/50 EDTA in titration. The…

A: The hardness degree can be calculated in term of CaCO3 equivalent asDegree of Hardness=Wt. of…

Q: Drinking water with negligible lead content was fortified with 2.28 µg Pb(II)/L. Triplicate…

A: Given: Concentration of drinking water with negligible Pb content = 2.28 µg Pb(II)/L Mean of…

Q: in a standard addition calibration method, 50.0 ml volumetric flasks were used. A 5.0 ml aliquot of…

Q: A student wanted to determine the level of lead in amoxicillin powder, so he transferred 148 mg of…

A: Given the absorbance of the diluted solution, Y = 0.48 Calibration equation is: Y = 12.25X - 0.05…

Q: Chemist Angelica Benjamin Mai Jesus Measurements 35.6 ppt 35.2 ppt 36.2 ppt 31.7 ppt 37.4 ppt…

A: Precision is defined as the closeness of the measurements to each other. More the closeness of data…

Q: A student wanted to determine the level of lead in amoxicillin powder, so he transferred 148 mg of…

A: Given: The absorbance of the diluted solution, y = 0.48 Calibration equation is given by y = 12.25…

Q: A series of standards were analyzed which gave the following results SOLUTION % Transmittance 0 mL…

A: Beer-Lambert Law: The absorbance (A) is proportional to the concentration (c) of the solution and…

Q: A compound X is to be determined by UV/Visible spectrophotometry. A calibration curve is constructed…

A: The light absorbed by the solution is known as absorbance.

Q: 1. Consider the following data set. Concentration, mg/L 0.100 0.200 0.300 0.400 0.500 Write capital…

A: The given data of concentration and absorbance is: Concentration, mg/L Absorbance 0.100 0.125…

Q: 2. Concentration of metal ion. Absorbance of metal ion in solution 0.316 Concentration of metal ion…

A: 2. Given: Initial Volume of Unknown Sample = 20 mL Volume of Final diluted sample = 25 mL…

Q: The concentration of NaOH from the best three of your trials. 2. The average concentration of 3 of…

A: Given: Titration KHP (g) Vfinal (mL) Vinitial (mL) Vtotal NaOH(mL) 1 0.7027 34.20 0.0 34.20 2…

Q: estion 20 Question 19 Consider the standard curve of DCIP (2,6-dichlorophenol indophenol) shown…

A: 19) The relation between the absorbance and concentration of a compound can be shown by the…

Q: Tube Dilution pH (acid) [H+] 10-1 (aseq) Hd 13 [H+] 1. 2. 10X 1.92 12.05 11.12 10^-2 3. 100X 2.75…

A: Introduction: As per Bronsted-Lowry concept, an acid is a substance that can donate H+ ions and base…

Q: To be considered precise, the standard deviation of a set of measurements should be less than 10% of…

A: Average of given set of values is defined as the sum of the given values divided by the number of…

Q: From a 10-mL sample, a 1-mL aliquot was taken and diluted to 100mL. From this, a 5-mL aliquot was…

A: The diluted conc. of any solution can be calculated by using the dilution formula:…

Q: Concentration (M) Absorbance 0.0200 0.102 0.0400 0.204 0.0600 0.306 0.0800 0.408 0.100 0.510 An…

A: As per Lambert-Beer's law, absorbance of a solution is directly proportional to concentration of…

Q: Sally obtains a standard calibration curve for their assigned food dye by plotting absorbance versus…

A: Given: standard calibration curve: y = 1.585x + 0.041 y-axis: Absorbance x-axis: Concentration…

Q: Using M1V1=M2V2 Make 100ml of a solution that contains 0.5mM MgCl2, 15 mM CaCl2 and 120 mM KCl 0.5M…

A: Molarity is defined as “the mole of the solute per unit volume of the solution”. It is represented…

Q: Determine phosphate concentration of a water sample using the following information: Standard…

A: Given, Absorbance of water sample = 0.013 Slope = 1763.2 y-int = 0.011806 R2 = 0.99181 Concentration…

Q: A titration was carried out to determine the volume of base needed to neutralize an acid. Five runs…

A: The neutralization reaction or the acid-base reaction is often employed as the basis for determining…

Q: Analysis of Percent Organic Matter of * a soil sample was conducted and the data are shown below.…

Q: Absorbance Volume Concentration ug/mL (mL) of each standard 1 0.000 2 1 0.005 3 2.5 0.010 4 6.25…

A: The linear regression equation Y = 0.0036x + 0.0006

Q: The following Absorbance vs concentration of nitrite graph is obtained for a set of data: y =1.6628x…

A: The details solution for this is provided below in step II.

Q: The absorbance of an unknown dye solution is measured to be 0.47 by a spectrometer. The linear…

A: The given expression for the linear equation for the spectrometr calibration is ; Y = 2156.5 X +…

Q: Table 5. Drink mix concentrations and absorbances for constructing a standard curve [H3O+] (M)…

Q: II. Determination of Total Hardness of Water Source of water sample: Volume of water sample 22.00 mL…

A: Given that, Volume of EDTA solution consumed (V1)=14.06mL Molarity of standard EDTA solution used…

Q: A lab pair’s Beer’s Law calibration graph 0.08 < A < 0.79 had a best-fit line of A = 0.013 C –…

Q: ased on the data on the table, show the calibration curve and determine the concentration of the…

A: Given the absorbance of the unknown water sample = 0.121 The calibration curve is drawn by taking…

Q: Blue Blue dye stock solution 0.293 M Absorbance at 630 nm 0.00265 Calibration curve y = 0.0833x A…

A: a) Calculation of theoretical molar concentration: MinitialVinitial=MfinalVfinal0.293 M×2.79…

Q: What is the percent error of the Ksp of Ca(OH)2 if the experimental value is 9.1 x 10^-5 and the…

A: Given Experimental value = 9.1 * 10-5 Accepted value = 5.5 * 10-6

Q: The trendline for a calibration curve is y=4.299x+-0.0001. The absorbance of a solution of the…

A: The concentration of the unknown solution is 0.0189 uM.

Q: 2. Using the Data and Graph below (with the equation for the best fit line), Calculate the concent…

A: In the given equation Y is absorbance and x is concentration. Given equation, y=1.1429x-0.0007…

Q: Three titration trials were performed and three molar concentrations of NaOH were calculated. The…

A: We would use formula to calculate standard deviation .

Q: The lead level in a sample of contaminated soil was determined using AAS. A 2.0 g sample was…

A: This question is related to finding out the sensitivity of the method. Basically gradient or slope…

Q: A Chromatographic quantitation of Methylene blue have the following data. Calculate the…

A: First, we have to plot the Peak Area versus standard concentration plot for the three standards.…

Q: In the experiment "Beer-Lambert's Law and Spectrophotometry", you prepared a calibration plot…

Q: A sample was analysed for its Calcium concentration. A number of standard solutions were prepared…

A: The plot of concentration will give the relation between concentration and absorbance. If one…

Q: ample tub Deprot. samples Glucose Standards A B E #1 #2 O Standard/samples (r) 0.2 0.2…

A: The question involves the beer lambert law equation: A=ε c lA is the absorbance; c= concentrationl =…

Q: The analysis of DDT in a water sample resulted to a peak area of 0.250. Calibration curve is NOT…

A: The concentration of DDT in a water sample is required to be calculated given that the chromatogram…

Q: 50 ppm .00 ppm 50 ppm 100

A: The solution is given below -

Q: Make a standard calibration curve wherein the x-axis is the total concentration of standard 1 to 6…

A: A question based on tools in analytical chemistry that is to be accomplished.

Q: Given the data obtained from the voltmeter ranking of metals, calculate the standard deviation for…

A: Given: The given data is:

Q: As part of an analytical chemistry laboratory course, a student measured the Ca2+ content in two…

A: Given Data: Method City-Supplied Drinking Water Well-Supplied Drinking Water FAAS 57.57±0.68…

Q: explain what the results of this experiment are and the purpose Table 2 Absorbance vs CoCl2…

A: Purpose of the experiment is to draw the calibration curve from standard data , to know then find…

Q: A 0.1 g amine-containing compound is dissolved in water then diluted to 100 mL. You subject it to…

A: We have given that Absorbance (A) = 0.545 Mass of amine = 0.1 g The molar absorptivity (ε) =…

Q: A standard curve for glucose analysis was prepared.The slope (m) was found to be 1.341 while the…

A: Given: Slope(m) = 1.341 y-intercept = -0.333 Absorbance (y) = 0.151

Concept explainers

Spectroanalytical Methods

Spectroanalytical methods measure the wavelength and intensity of radiations that are either emitted or absorbed by a molecular or atomic species. These methods are useful for evaluating the electronic or atomic arrangement of the molecules of a given analyte.

Question

100%

Calculate the concentration of Cu in the sample by calibration curve using the following data

Concentration (ppm)	Absorbance
2	0.150
4	0.301
6	0.455
8	0.598
10	0.745
sample	0.360

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Analysis

VIEW

Calculation

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

The absorbance for a dye sample of unknown concentration is measured and the corrected absorbance is 0.666. The standard curve created is found to have this linear equation: y = 0.153x + 0.043 Calculate the concentration (ug / mL) of the dye sample. 4.54 3.33 4.07 5.17 2.07
An unknown concentration of [FeSal]+ gave an absorbance reading of 0.301. Calculate the concentration of the solution, given that the slope of the standard curve was 1280 and the y intercept was -0.00821.
A standard curve of absorbance vs. concentration has a linear trendline of y = 0.56x + 0.987. Use this trendline to calculate the concentration of an unknown sample that has an absorbance of 1.245.
Monomer-dimer formation can affect the absorbance measurements using Beer’s law, it is an example of: A. chemical deviation B. instrumental deviation C. real deviation D. instrumental deviation
Please complete Table 2 and show the calculations for protein concentration and the concentration of the undiluted sample. a). Using Excel software, enter data from Table 1 to plot a standard curve (corrected average absorbance on Y-axis and protein concentrations on X-axis). The standard curve must contain correct labels on both axes. b). From the standard curve, obtain a best fit line and equation. c). Use the best fit equation and data from Table 2 to find the concentrations of proteins in sample A2-D2 and E1. [onto your plotted standard curve, indicate where A595 of A2-D2 and E1 are located] d). Calculate the concentrations of proteins in undiluted samples A to E. Thank you very much.
The absorbance values at 250nm of 5 standard solutions, and sample solution of a drug are given below: Conc. (ug/ml) A 250 nm10 0.16820. 0.32930 0.50840. 0.66050 0.846Sample. 0.661Calculate the concentration of the sample
Based on the data on the table, show the calibration curve and determine the concentration of the water sample with an absorbance of 0.121. Concentration (ppm) Absorbance 0.0000 0.0240 0.0200 0.0320 0.0400 0.0500 0.0600 0.0680 0.0800 0.0820 0.1000 0.0900 0.2000 0.1690 0.3000 0.2390
A standard curve was performed using an Absorbance spectrophotometer, and the equation of that line was determined to be y = .1563x + .025. The absorbance of an unknown was measured at .35. Calculate the concentration of the unknown according to the standard curve.
What is the percent transmittance (%) if the absorbance (A) is 0.774? Show your solution
Five standard chromium (VI) solutions were prepared through serial dilution technique with corresponding absorbance readings at 540 nm wavelength (as follows: Absorbance Concentration A1 = 0.650 C1 = 1.9 ppm A2 = 0.712 C2 = 4.0 ppm A3 = 1.370 C3 = 6.0 ppm A4 = 2.050 C4 = 8.0 ppm A5 = 3.423 C5 = 10.0 ppm The sample solution gives an average absorbance reading of 0.713. What is then the concentration of chromium (VI) ion in the sample?
Five standard chromium (VI) solutions were prepared through serial dilution technique with corresponding absorbance readings at 540 nm wavelength as follows: Absorbance Concentration A1 = 0.650 C1 = 1.9 ppm A2 = 0.712 C2 = 4.0 ppm A3 = 1.370 C3 = 6.0 ppm A4 = 2.050 C4 = 8.0 ppm A5 = 3.423 C5 = 10.0 ppm The sample solution gives an average absorbance reading of 0.713. What is then the concentration of chromium (VI) ion in the sample? (Note: please provide necessary solutions)
Based on the calibration curve, what is the molar concentration for a solution with a measured absorbance of 0.383?