Complete the reagent table (check procedure for acid concentration) and calculate the theoretical yield. Calculate/discuss the percent yield. How efficient was the reaction? Are there any key areas in this experiment that caused a significant drop in yield? [Discussing how product was lost in the reaction rather lost in transfer steps will get the most points here] Information: 11 mmol of 2-methylcyclohexanol. 1.3 mL of 9 M sulfuric acid. Actual Yield: 0.626 grams.

Complete the reagent table (check procedure for acid concentration) and calculate the theoretical yield. Calculate/discuss the percent yield. How efficient was the reaction? Are there any key areas in this experiment that caused a significant drop in yield? [Discussing how product was lost in the reaction rather lost in transfer steps will get the most points here] Information: 11 mmol of 2-methylcyclohexanol. 1.3 mL of 9 M sulfuric acid. Actual Yield: 0.626 grams.

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter20: Nucleophilic Substitution Reactions: Competing Nucleophiles

Section: Chapter Questions

Problem 8Q

See similar textbooks

Similar questions

10.5mL (mw 106) of benzaldehyde and 2.9g(3.63mL, mw 40) of acetone react with 5g of NaOH and 25mL of Ethanol to form 6.7g of Dibenzalacetone. What is the theoretical, actual and percent yield?
There's 1 drink (and you are asked to determine the glucose concentration in the drink in the units of g/100mL. (Why these units? Well, once you have the concentrations in g/100mL you will be able to compare your values with the nutritional values given on the drink bottles’ labels). The sample of the drink was diluted 1/100 (i.e. by a factor of 100). This was an essential step in the method because, without it, the machine used to analyse the glucose concentration (spectrophotometer) would have given an error as the concentration would have been too high for accurate detection. What this means for you is that the dilution factor will need to be taken into consideration in your calculations (remember the aim is to calculate the concentration in the original drink and not in the diluted drink). You measured the concentration of their diluted drink using the spectrophotometer and their results were provided to them in the units mM (millimolar). Glucose Concentration in mM of drink =…
There's 1 drink (and you are asked to determine the glucose concentration in the drink in the units of g/100mL. (Why these units? Well, once you have the concentrations in g/100mL you will be able to compare your values with the nutritional values given on the drink bottles’ labels). The sample of the drink was diluted 1/100 (i.e. by a factor of 100). This was an essential step in the method because, without it, the machine used to analyse the glucose concentration (spectrophotometer) would have given an error as the concentration would have been too high for accurate detection. What this means for you is that the dilution factor will need to be taken into consideration in your calculations (remember the aim is to calculate the concentration in the original drink and not in the diluted drink). You measured the concentration of their diluted drink using the spectrophotometer and their results were provided to them in the units mM (millimolar). Glucose Concentration in mM of drink =…
Ethyl alcohol (C2H5OH) may be prepared by the fermentation of glucose (C6H12O6) as indicated by the equation: yeastC6H12O6 ----> C2H5OH + CO2 74.12 mL of ethyl alcohol (specific gravity = 0.790) was collected by this fermentation pro- cess. What mass of glucose was used?
A mixture of ethanol (ethyl alcohol) and water contains 40.0% water by mass.(a) Assuming volume additivity of the components, estimate the specific gravity of themixture at 20°C. What volume (in liters) of this mixture is required to provide 150 mol ofethanol?(b) Repeat Part (a) with the additional information that the specific gravity of the mixture at20°C is 0.89045 (making it unnecessary to assume volume additivity). What percentage errorresults from the volume-additivity assumption?
Explain why it is problematic to include a constraint such as the following in an LP model for a blending problem: Total octane in gasoline 1 blend $ divided by Barrels of gasoline 1 blended daily which is greater thanor equal to 10
100 g of soil is leached with a strong solution of Calcium chloride such that all the exchange sites are occupied by Ca2+. The soil is subsequently leached again with a strong solution of magnesium chloride. It is determined that the resulting 100 mL leachate contains 5000 mg of Ca2+. What is the soil CEC (cmolc/kg)? The atomic wt. of Ca is 40 g/mol.please answer in word don't image upload thank you.
The %purity of a powdered crude sample of Na2CO3 containing only inert impurities is to be determined by reacting 225.0 mg of the crude sample to 10.0 mL of 3.00 M HCl solution, and bubbling the resulting CO2(g) product in water that is at exactly 29 °C. After the reaction has completed, the level of the liquid inside the eudiometer rests 4.30 cm above the water level in the beaker. The graduation on the eudiometer indicates that the trapped gas is 44.37 mL. The experiment was done under a barometric pressure of 755.2 torr. a. How many moles of CO2 were collected? b. What is the percent purity of the sample? Round off to the nearest whole number
The %purity of a powdered crude sample of Na2CO3 containing only inert impurities is to be determined by reacting 225.0 mg of the crude sample to 10.0 mL of 3.00 M HCl solution, and bubbling the resulting CO2(g) product in water that is at exactly 29 °C. After the reaction has completed, the level of the liquid inside the eudiometer rests 4.30 cm above the water level in the beaker. The graduation on the eudiometer indicates that the trapped gas is 44.37 mL. The experiment was done under a barometric pressure of 755.2 torr. What CASE does this experiment satisfy?
Show all steps leading to the final answer po. Here’s a pdf file in accordance with the topic po: https://drive.google.com/file/d/1_FnDtXCrFKSol3RNWIG_9tNQ7IxgxD6t/view?usp=drivesdk
Using the percent purity calculations, determine the percent yield of synthesis of aspirin. Part I Synthesis of Aspirin Mass of salicylic acid used (g) 2.029g Volume of acetic anhydride used (mL) 5ml Mass of acetic anhydride used (vol. × 1.08 g/mL) 5.4g Mass of aspirin synthesized (g) 3.256g Part II Melting Temperature Data Melting temperature (°C) 133°C Part III Salicylic Acid Standard Stock Solution Initial mass of salicylic acid (g) 0.210g Moles of salicylic acid (mol) 0.0147 mol Initial molarity of salicylic acid (M) 0.724 M Part III Beer’s Law Data for Salicylic Acid Standard Solutions Trial Concentration (M) Absorbance Water (mL) 1 10 0.301 0 2 7.5 0.219 2.5 3 5.0 0.163 5.0 4 2.5 0.074 7.5 Best-fit line equation for the salicylic acid standards Test of the Purity of the Synthesized Aspirin Initial mass of aliquot of product (g)…