Constants Part A During an action potential, Na* ions move into the cell at a rate of about 3 x 10 mol/ms How much power must be produced by the "active Nat pumping" system to produce this flow against a +30-mV potential difference? Assumo that the axon is 90 cm long and 20 um in diameter. Express your answer using two significant figures. P = Submit Request Answer

Constants Part A During an action potential, Na* ions move into the cell at a rate of about 3 x 10 mol/ms How much power must be produced by the "active Nat pumping" system to produce this flow against a +30-mV potential difference? Assumo that the axon is 90 cm long and 20 um in diameter. Express your answer using two significant figures. P = Submit Request Answer

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter34: Particle Size Determination

Section: Chapter Questions

Problem 34.10QAP

See similar textbooks

Similar questions

When the transport of the 0,05moldm' KCI aqueous solution was measured at 25°C using the interfacial transfer method, the interface with the CdCl2 aqueous solution moved by 6.3cm for 30 minutes. The current flowing was 0.0052 A and the cross-sectional area of the tube was 0.15 cm이었다. Find the carrying rate of K+?
An analyst wants to find out the active surface of his electrode before conducting his analyzes. To do this, he carried out a series of measurements by cyclic voltammetry (CV) using a 1 mM solution of K4Fe(CN)6 dissolved in 0.1M NaCl. He recorded the anodic peak intensity (ip) corresponding to the oxidation of Fe(II) to Fe(III) as a function of the scanning speed (v) of the CV (see table). What is the active surface of the electrode? Data: Fe diffusion coefficient (CN)64-, D = 6.67x10-6 cm2/s Randles-Sevcik equation ip = (2,69x105)n3/2ACD1/2v1/2 rate (v/s) ip (A) 5,00E-02 5,75E-05 1,00E-01 7,68E-05 2,00E-01 9,94E-05 5,00E-01 1,42E-04 1,00E+00 2,07E-04
The data below was obtained with a Cl- ISE to prepare a plot of mV vs. log[Cl-]. Assume the unknown saltwater solution was diluted as in the procedure before being measured. What is the ppm Cl- of the undiluted unknown solution? Cl- Concentration (ppm) Potential (mV) 10 160 100 94 1000 40 Diluted Unknown Saltwater 132
The transfer coefficient of a certain electrode in contact with M2+ and M3+ in aqueous solution at 25 °C is 0.42. The current density is found to be 17.0 mA cm2 when the overpotential is 105 mV. What is the overpotential required for a current density of 72 mA cm−2? Hint: See hint to Exercise E19D.1(a).
What is the actual or real-life application of electrogravimetric analysis? Include the specific methodology.
An amino acid moves randomly through water with steps of about 3 angstroms (3 x 10^-8 cm) in length at a rate of 1 x 10^10 steps per second. This substance is passing through a reverse phase HPLC column which has a plate height of 0.010 cm. 1. Estimate the diffusion coefficient for the amino acid in water. 2. Calculate the width at the base of the elution zone after the amino acid has migrated 50 cm through the column
) 0.025 M CH3COOH solution has a specific conductance of 2.33X10-4 Scm-1,and molar conductivity at infinite dilution is 364.13 S.Cm2.mol-1. What is itsdegree of dissociation?
Use the data in Table 19D.1 for the exchange-current density and transfer coefficient for the reaction Fe3+ + e− → Fe2+ on platinum at 25 °C to identify the current density needed to obtain an overpotential of 0.30 V as calculated (i) by using the Butler–Volmer equation, and (ii) by assuming that the current is entirely anodic. Comment on the validity of the latter assumption.
A typical exchange-current density, that for H+ discharge at platinum, is 0.79 mA cm−2 at 25 °C. Use the Butler–Volmer equation to calculate the current density at an electrode when its overpotential is (a) 10 mV, (b) 100 mV, (c) −5.0 V. Take α = 0.5.
A sample of steel (0.506 g) was digested in acid and the solution made up to 100 cm3 with deionised water. Aliquots (25.0 cm3) of this solution were transferred into two volumetric flasks (100 cm3) labelled A and B. Flask A was made up to volume with deionised water. To flask B was added 10.0 cm3 of a 260 ppm standard solution of Mn2+ which was then also made up to volume with deionised water. The following absorbance results were obtained: Solution A = 0.356, Solution B = 0.578. Use these results to calculate the percentage (% w/w) of manganese in the steel sample.
An aquifer contaminated with petroleum is found to have the following component concentrations at a particular site: benzene 158 ppm toluene 124 ppm ethylbenzene 91 ppm xylene 45 ppm n-heptadecane 161 ppm pristane 84 ppm Provide an estimate for the age of the spill at this site using (a) BTEX ratio and (b) nC17:Pr ratio. Show your calculations and use units throughout. Give proper s.f. for the answer.
A plot of current (amperes) versus the square root of scan rate (volts/sec) for the ferricyanide/ferrocyanide (n=1) reaction give a slope value of 0.0001257. The electrode diameter is 1.5 mm. The concentration of ferricyanide is 10 mM. Calculate the diffusion coefficient in cm2/sec.