Example: What is the pressure at the center of the pipe B? Example: What is the pressure at the center ofpipe B?+) By = 10 kN/m3y = 20 kN/m350 cm450 cm10 cmsino- Źo =Sin6=3618735

Given, γ1=10 kN/m3γ2=20 kN/m3

Answered: Example: What is the pressure at the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Equation 6.16: εT = ln(li / l0)
Q 1(a) Use the below given data and calculate the metacentric height. Note: Explain each and every step. w= 200g W=2533.2g Displacement x (mm) 80 60 40 20 0 20 40 60 80 Tilt angle Ɵ (degree) 9.5 7.5 5.5 3 3 5.5 7.5 9.5 M.H (b) By using U-tube manometer how can you find out the pressure head? (c) If you are lacking of equipment, how can you determine the discharge of any channel?
Subject is hydraulics A closedcylindrical vessel 5 ft in diameter and 6 ft high is 3/4 filled with molasses(SG = 1.24) and rotated about its vertical axis. Air is pressurized at 14.5psi. a. If w = 50 rpm, solve for thepressure at the base at the circumference of the vessel b. If w = 75 rpm, solve for thepressure at the base at the circumference of the vessel c. Solve for w (in rpm) so that thereis no water at the base of the vessel within 1.8 ft radius
The hydrostatic pressure in a 24" diameter ductile iron water main is 75 p.s.i. If the thickness of the iron is 1/2", then what is the tension in the iron due to the hydrostatic pressure in p.s.i ?
How to calculate permeability according to silica bead characxteristics without knowing pressure drop? silica diameter: 2.5mm Inlet mass flow rate: 0.3m^2/min Inlet Temperature: -10 degree C
A differential pitot tube located at the center of a cylindrical air tube produces 2.6 in. of water pressure. What is the velocity at the impact end of the pitot tube? The impact gauge reads 2.6, 2.6, 2.5, 2.1, 1.8 when placed at points 1-5 in Fig. 3.10. What is the average velocity in the tube? What factor would be applied to the center reading to indi- cate a true average velocity? Note: In actual practice it would be necessary to check this factor through the entire range of velocities to be encountered, because variation may be expected.
A pump has a displacement of 90 cm3 . It delivers 75 Lpm at 1300 rpm and 75 bar .If the prime mover torque is 90 N-m. What is the theoritical troque required to operate the pump? a. 107.48 N-m b. 75 N-m c. 120.54 N-m d. 90 N-m
Show complete solution pls SN = 93
With free body diagram please thank you. Clear and complete solution please. 3. A shaft 70 mm in diameter is being pushed at a speed of 400 mm/s through a bearing sleeve 70.2 mm in diameter and 250 mm long. The clearance, assumed uniform, is filled with oil at 20°C with v = 0.005m²/ s and sp. gr .=0.9 Find the force exerted by the oil in the shaft.
29. A mixture of water and steam flowing out of a vent at 200 psia and quality of 0.27. Find the void fraction at critical flow condition according to Moody and Fauske models. [Ans. αMoody = 0.65 and αFauske = 0.81].
An oil well has the following specifications; • Tubing diameter = 2.875” • Tubing roughness = 0.0254 mm • Flow rate = 600 bbl/d • Average reservoir pressure is 4230 psig and Pb is 46335 • Well Depth = 133000 ft 1- Calculate Pwf at 1000, 3000 and 4500 psi. 2- Calculate Pwf at tubing ID 3”, 4” and 5”. Plot Pwf vs Q and determine optimum production rate for both cases Fluid properties GOR 1930 scf/stb Gas Sg is 0.74 Oil API 42 WOR is 0.1 Reservoir temperature 175 F
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. ( WITH FREE BODY DIAGRAM ) CHOIECES: A.2.56 B.-2.72 m C.12.74 m D.-4.67 m

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Example: What is the pressure at the center of pipe B? B -y = 10 kN/m3 Y = 20 kN/m3 50 cm 10 cm 50 cm 13 sino- Ź D =Sin 3 4 6=36187 35