Extraction of the aqueous salicylic acid solutions with 10% ethyl acetate/hexane (density ~ 0.7 g/ml) will give two layers in the separatory funnel. a. Will the aqueous layer be the upper layer or the lower layer? b. If dichloromethane (density ~ 1.3 g/ml) were substituted for the 10% ethyl acetate/hexane solution, which layer would be the aqueous layer?

Extraction of the aqueous salicylic acid solutions with 10% ethyl acetate/hexane (density ~ 0.7 g/ml) will give two layers in the separatory funnel. a. Will the aqueous layer be the upper layer or the lower layer? b. If dichloromethane (density ~ 1.3 g/ml) were substituted for the 10% ethyl acetate/hexane solution, which layer would be the aqueous layer?

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter81: Extractions, Separations, And Drying Agents

Section: Chapter Questions

Problem 5P

See similar textbooks

Similar questions

Using the table on slide 7, what ORGANIC solvent could you use to do an extraction of something fromisooctane? What about from acetic acid? b. On slide 7, it says the solvents in grey would not work to extract an aqueous layer. Why not? 6. a. So if you were trying to extract 15mL of an aqueous layer, why wouldn’t you want to use 45mL of theorganic solvent? Why would 20mL be better? b. Why wouldn’t you use 2mL of the organic solvent?
What are emulsions? Why do they form during extractions? How is their formation minimized?
What are emulsions? Why do they form during extractions? How is the formation of an emulsion minimized?
1. Which of the following may cause an increase in the calculated percent recovery of the recrystallized benzoic acid? a.Adding too much solvent in the receiving flask during hot filtrationb.Using cold water in rinsing the residue from the flask during hot filtration c.Using fluted filter paper during hot filtrationd.Not adding animal charcoal to the solution2. Which set of reagents can confirm that sulfate ions are present in two unkown solutions? a.1.0 M NaOH and excess NH3 b.0.1 M Ba(NO3)2 and 0.01 M KMnO4 c.1.0 M NaOH and 0.1 M K2Zn3[Fe(CN)6]2d.0.1 M Ba(NO3)2 and 1.0 M CH3COOH
Some procedures include the addition of sodium carbonate before liquid-liquid extraction. What is the purpose of this step?
Why sometimes derivatization is used in the sample preparation for GC-MS?
The key to a successful HPLC procedure is good sample separation which is represented by a clean peak for each individual compound. What should we do to ensure a good sample preparation? A. Use a column and a mobile phase with different polarity B. Use a column and a mobile phase with the same polarity C. Use a lower temperature higher than the mobile phase boiling point D. All of those
What is the reason for using as little ethanol as possible to dissolve the crude product before recrystalliazation?
If you are performing a solvent extraction using 1M HCl (Density slightly > 1.00 g/mL) and diethyl ether (density = .706 g/mL) which layer is the aqueous layer? which is the bottom and top layer?
We want to extract terpenoids from an aqueous sample by continuous liquid-liquid extraction. Which of the following solvents is not suitable for this purpose? Why? Propanone (acetone), dichloromethane, heptane.
In addition to a low boiling point and immiscibility with water, why is density important to consider in the selection of an extraction solvent? Would an organic liquid with a density of 1.006 g/mL make a good extraction solvent? Explain.Write the chemical reaction that took place during this experiment.
1. Basically, when is glass stoppered buret used? ______________________________ ____________________________________________________________________ When is rubber stoppered buret used? ____________________________________ ________________________________________________________________________________________________________________________________________ When is a PTFE buret used? _________________________________________________________ _ _________________________________________________________________________________ 2. Describe the recommended method for the manipulation of a buret stopcock during titration. ________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ 3. Why is it necessary to completely fill the rubber tubing of the stopcock with the…