II Review the body relative to the cross-section. Consider the pipe assembly shown in (Figure 1). Neglect the weight of the pipe. Take F1 = (200 i – 200 j – 200 k} N and F2 = {200 i + 500 j} N. Express your answers using three significant figures separated by a comma. Vy, V = -300,200 N Submit Previous Answers Correct Part C Determine the x, y, and z components of internal moment acting at a section passing through point B on the left part of the body relative to the cross-section. Figure < 1 of 1 Express your answers using three significant figures separated by commas. vec ? M2, My, M; = 300,300,500 N.m B Submit Previous Answers Request Answer 1m X Incorrect; Try Again; One attempt remaining 1.5 m F, Provide Feedback Next >

II Review the body relative to the cross-section. Consider the pipe assembly shown in (Figure 1). Neglect the weight of the pipe. Take F1 = (200 i – 200 j – 200 k} N and F2 = {200 i + 500 j} N. Express your answers using three significant figures separated by a comma. Vy, V = -300,200 N Submit Previous Answers Correct Part C Determine the x, y, and z components of internal moment acting at a section passing through point B on the left part of the body relative to the cross-section. Figure < 1 of 1 Express your answers using three significant figures separated by commas. vec ? M2, My, M; = 300,300,500 N.m B Submit Previous Answers Request Answer 1m X Incorrect; Try Again; One attempt remaining 1.5 m F, Provide Feedback Next >

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

mechanics of deformable bodies The cylindrical tank has an outer radius of 1.5m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal stress.
The Bulk Modulus of 1 kg of water is 2.2 GPa. If the percentage reduction in volume is 6%, determine the pressure applied. Express your answer in the appropriate SI unit Round off ONLY the final result to three decimal places as applicable.
A cylindrical pressure vessel has an inner diameter of 4 ft and a thicknessof 1 2 in. Determine the maximum internal pressure it can sustain so that neither its circumferential nor its longitudinal stress component exceeds 20 ksi. Under the same conditions, what is the maximum internal pressure that a similar-size spherical vessel can sustain?
8. In a hot air balloon launch, it was known that the material used in the construction amounts to 200kg and that the loading capacity of the cage was 250kg. If the hot air balloon has to travel in air where the ambient temperature and pressure was 25°C and 101.325kPaa, determine the minimum diameter (meters) of the balloon (assume to be spherical) needed to course the air if the setting temperature of hot air inside the balloons is 80°C. Assume pressure inside the balloon to be atmospheric. Draw a figure or FBD that will support the problem. Explain each step by step formula.
In inserting an aluminum piston into a steel cylinder, it is given that the inside diameters of the cylinder and of the piston are 0.500 m and 0.4998 m, respectively, at 25OC. The temperature to which they are heated to obtain a perfect fit is 55.8 degrees celsius. Show the solution.
What is the resulting modulus of ln (2 +3 j)?
A cylindrical pressure vessel has an inner diameter of 1.2 m and a thickness of 12mm. Determine the maximum internal pressure it can sustain so that neither itscircumferential nor its longitudinal stress component exceeds 140 MPa. Under thesame conditions, what is the maximum internal pressure that a spherical vessel with a similar inner diameter can sustain?
The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a pressure p. The thickness r,-r; is small compared to r; (a) Determine the axial force F in the ring in terms of p, w and r;. Hint: Consider a FBD by cutting the ring+membrane in two. (b) Determine the hoop stress in the ring. (c) Determine the hoop strain in the ring. The modulus of elasticity for the ring is E. (d) Relate the hoop strain to the change in the inner radius of the ring after this pressure is applied, and use this to get the change in the inner radius in terms of p, E, w, r, and ri- (PLEASE ANSWER ASAP AND CORRECTLY)!
he region of safety in maximum shear stress theory contains which of the given shape *
Janice is grilling a steak for her July 4th barbecue dinner. The steak initially weighs 300 grams and is 25 mm thick. After grilling it for a while, she considers the steak done, and measures it again: it now weighs 215 grams, and is 15 mm thick. For both the cooked and uncooked steak, she uses the thumb-test to determine the done-ness, i.e. she uses her thumb (area ~5cm2) to push down with a force of 5 N. The uncooked steak compresses by 7 mm, and the cooked steak by 2 mm. Calculating elasticity What is the elasticity of the raw steak? Express your answer in Pascals but without including the units in your answer. What is the elasticity of the cooked steak? Express your answer in Pascals, but without including the units.
Evaluate the following to three significant figures and express each answer in SI units using an appropriate prefix:(212 mN)^2
The wires AB and AC are made of steel, and wire AD is made of copper. Before the 150-lb force is applied, AB and AC are each 60 in. long and AD is 40 in. long. If the temperature is increased by 80F, determine the force in each wire needed to support the load. Each wire has a cross-sectionalarea of 0.0123 in2. Take Est = 29(10 3) ksi, Ecu = 17(10 3) ksi, fast = 8(10 6)>F, acu = 9.60(10 -6)>F.