mixture of three components is separated using paper chromatography, and each component is analyzed using absorption. With tandards containing 100 ppm of each component run simultaneously, the following data were obtained: cmpd A, 0.72 absorbance 3, 0.55; C, 0.80. For the unknown mixture, the data obtined when run under identical conditions were as follows: cmpd A, .0.15 bsorbance, B, 0.84; C, 0.75. ) Calculate the relative percentage composition of the unknown mixture.

mixture of three components is separated using paper chromatography, and each component is analyzed using absorption. With tandards containing 100 ppm of each component run simultaneously, the following data were obtained: cmpd A, 0.72 absorbance 3, 0.55; C, 0.80. For the unknown mixture, the data obtined when run under identical conditions were as follows: cmpd A, .0.15 bsorbance, B, 0.84; C, 0.75. ) Calculate the relative percentage composition of the unknown mixture.

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter31: Introduction To Analytical Separations

Section: Chapter Questions

Problem 31.32QAP

See similar textbooks

Similar questions

A mixture of three components is separated using paper chromatography, and each component is analyzed using absorption. With standards containing 100 ppm of each component run simultaneously, the following data were obtained: cmpd A, 0.72 absorbance; B, 0.55; C, 0.80. For the unknown mixture, the data obtined when run under identical conditions were as follows: cmpd A, 0.15 absorbance, B, 0.84; C, 0.75. a) Calculate the relative percentage composition of the unknown mixture. b) The distances traveled by the three components were 8.5, 6.3, and 5.5 cm, respectively. Sketch the appearance of the paper chromatogram. Label each spot. c) Calculate the Rf values if the solvent front is 18 cm.
A third spectrophotometric method for the quantitative analysis of Pb2+ in blood uses Cu2+ as an internal standard. A standard containing 1.75 ppb Pb2+ and 2.25 ppb Cu2+ yields a ratio of (SA/SIS)std of 2.37. A sample of blood is spiked with the same concentration of Cu2+, giving a signal ratio, (SA/SIS)samp, of 1.80. Determine the concentration of Pb2+ in the sample of blood.
A spectrophotometric method for the quantitative analysis of Fe2+ in blood uses Zn2+ as an internal standard. A sample containing Fe2+ and Zn2+ with final concentration of 3.25 ppb and 0.75 ppb, respectively, that yields a signal of 0.423 for Fe2+ and 0.650 for Zn2+. Subsequently, a sample of blood is spiked with Zn2+ to give the same final concentration and yielded a signal of 0.832 for Zn2+ and 0.110 for the unknown concentration of Fe2+. Determine the concentration of Fe2+ in the sample of blood.
A spectrophotometric method for the quantitative determination of the concentration ofPb2+ in blood yields an Ssamp of 0.133 for a 1 mL sample of blood that has been diluted to 6 mL. A second sample is spiked with 1 µL of a 1467 ppb Pb2+ standard and diluted to 6 mL, yielding an Sspike of 0.491. Determine the concentration of Pb2+ in the original sample of blood.
Two components in an HPLC separation have retention times thatdiffer by 22 s. The first peak elutes in 10.5 min and the peakwidths are approximately equal. Use a spreadsheet to find theminimum number of theoretical plates needed to achieve thefollowing resolution, Rs, values: 0.50, 0.75, 0.90, 1.0, 1.10, 1.25,1.50, 1.75, 2.0, and 2.5. How would the results change if peak 2were twice as broad as peak 1?
Repeat analyses of the Zn content of an ore leachate by atomic absorption spectrophotometry yielded the following data for successive samples: 2.11, 2.09, 2.29, 2.13, 2.14 ppm Zn. Using 95% confidence criteria which of the following statements is true? Select one: a. no data should be rejected b. 2.09 should be rejected c. 2.09 and 2.29 should be rejected d. 2.29 should be rejected.
What are the parameters that can be used for analytes identification and quantification using Cyclic Voltammetry, respectively?
The following calibration data were obtained by an atomic absorption spectrophotometric (AAS) method for the determination of mercury in an herbal product. 1. Calculate the calibration sensitivity.2. Calculate the coefficient of variation for the mean at 6.00 ppm 3. What is the detection limit for the method? 4. What is the limit of quantitation for the method?
A 5.00-mL sample of blood was treated with trichloroacetic acid to precipitate proteins. After centrifugation, the resulting solution was brought to pH 3 and extracted with two 5-mL portions of methyl isobutyl ketone containing the lead-complexing agent APCD. The extract was aspirated directly into an air/acetylene flame and yielded an absorbance of 0.527 at 283.3 nm. Five-milliliter aliquots of standard solutions containing 0.400 and 0.600 ppm of lead were treated in the same way and yielded absorbances of 0.396 and 0.599. Find the concentration of lead in the sample in ppm assuming that Beer’s law is followed.
(i) Calculate the capacity factors (k') for both compounds A and B and the selectivity factor (a) between them, commenting on the values. (ii) Calculate the resolution between A and B and comment on it. (iii) Using the peak for A, calculate the number of theoretical plates for the GC column and comment on the quality of the column.
A 5.00-mL sample of blood was treated with trichloroacetic acid to precipitate proteins. After centrifugation, the resulting solution was brought to pH 3 and extracted with two 5-mL portions of methyl isobutyl ketone containing the lead-complexing agent APCD. The extract was aspirated directly into an air/acetylene flame and yielded an absorbance of 0.569 at 283.3 nm. Five-milliliter aliquots of standard solutions containing 0.400 and 0.600 ppm of lead were treated in the same way and yielded absorbances of 0.396 and 0.599. Please calculate the concentration of lead in the sample in ppm.
You have carried out an experiment using the spectrophotometry concept. A solutioncontaining compound X is mixed with reagent 1 and then reagent 2. This mixture produces ablue colour whose absorbance (A) could be read at 550 nm. The results are shown below If the standard solution (compound X) used have a concentration of 1 mM: 3. If the absorbance was read using 1 cm diameter cuvettes, calculate the molar extinctioncoefficient for compound X in the solution. State the unit for the coefficient. Assumeeach molecule of X produces one molecule of coloured compound