potassium hydrogen phthalate is a primary standard used to measure the concentration of NaOH solutions. find the true mass of potassium hydrogen phthalate (density=1.636g/ml) if the mass weighed in the air is 4.236g. if you did not correct the mass for buoyancy, would the calculated molarity be too high or too low? the density of air is 0.0012 g/mL while that of the calibration weights is 8.0 g/mL.

potassium hydrogen phthalate is a primary standard used to measure the concentration of NaOH solutions. find the true mass of potassium hydrogen phthalate (density=1.636g/ml) if the mass weighed in the air is 4.236g. if you did not correct the mass for buoyancy, would the calculated molarity be too high or too low? the density of air is 0.0012 g/mL while that of the calibration weights is 8.0 g/mL.

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter11: Atomic Mass Spectrometry

Section: Chapter Questions

Problem 11.10QAP

See similar textbooks

Similar questions

Is the concentration of the solution prepared in the question below only approximate because sodium hydroxide is not a primary standard? * Find the mass in grams of sodium hydroxide that will be required to prepare a solution with a concentration of 0.500 mol·dm⁻³ in a 250 cm³ volumetric flask. [Round the answer to three decimal places. Do not type in the unit. Use a decimal point.] *
A. A group of students are doing an analysis of copper in 1-peso coin. They were tasked to prepare standard solutions and weigh the analyte as the end-product of their experiment. Explain the type of error they are incurring in their experiment. A. Marikit had very good precision but poor accuracy in her data. B. Volumetric flasks were placed inside the oven for drying before it was used. C. Trial 1 and 2 have values close to 30.0 mL while trial 3 gave 55.0 mL. D. The reagent used in determining copper was added incorrectly and gave a low yield.
Chemistry The levels of an organic pollutant (P) in the groundwater at the perimeter of a plant were a cause for concern. A 10 mL sample of the water was taken and the pollutant was extracted with 95% efficiency using 25 mL of diethyl ether. GC was used to analyse the concentration of P in diethyl ether. A calibration curve was plotted for a series of standards of P which yielded the following results: Peak Area Toluene Conc. (µg/ml) 12,000 2.6 23,700 5.0 35,500 7.7 46,800 9.9 31,250 Sample Determine the concentration of P in ppb in the initial groundwater sample.
To quantify the amount of ethanol in a beverage, a technician prepared the first solution which contained 4.90 grams unknown, 1.00 grams acetonitrile, and 4.10 grams water. After the GC analysis which reported the peak areas of 5,742 for ethanol and 3,829 for acetonitrile, the technician added 0.20 grams ethanol to the first solution and ran the GC analysis again. This time, the peak areas of 6,382 for ethanol and 3,709 for acetonitrile for solution 2 were obtained. What was the percent by mass ethanol in the original beverage?
To determine the organic material in a dried lake bed, the percent carbon by mass is measured at two different locations. To compare the means of the two different locations, it must first be determined whether the standard deviations of the two locations are different. For each location, calculate the standard deviation and report it with two significant figures. What is the calculated F value for comparing the standard deviations? Are the standard deviations for the two locations significantly different at the 95% confidence level? ample Location 1 (% C) Location 2 (% C) 1 10.40 10.10 2 10.30 10.90 3 10.30 10.20 4 10.40 10.70 5 10.30 10.30
A stock solution of 0.225 +/- 0.003 M NaNO2 was transferred to a 100 mL volumetric flask (class A) and diluted to the mark. If 7 mL of the stock solution was transferred using one 5-mL and two 1-mL volumetric pipettes, what is the new concentration of the solution and the uncertainty? Please show how to calculate the uncertainty, that is the one part I don't understand how to do
CHOICES: Increase, Decrease, No Effect and WHY 1. The actual concentration of the sodium hydroxide used in the calibration part of the experiment was lower than the stated value. However, the NaOH solution used in the determination of ΔHrxn was of the correct concentration. [magnitude of ΔHrxn] 2. The test tube used in the determination of the ΔHrxn for nitric acid was still wet with water. [ magnitude of ΔHrxn] 3. The actual concentration of the sodium hydroxide used in the calibration part of the experiment was lower than the stated value. [Ccal] 4. A wet pipette was used to transfer 10.00 mL of 1M HNO3 in the determination of ΔHrxn. [magnitude of ΔHrxn] 5. The thermometer and stopper were inserted to the test tube 5 minutes after adding the base in the calibration part. [Ccal]
What is the relative error in the ppt of the following data if the accepted value is 70.05 M? 70.24 M, 70.22 M and 70.10 M
If an instrument gives a response of 1240 for a standard containing 8 ppm of a substance, how much if this substance is in a sample that gives a response of 1705? Are any assumptions needed?
What are the differences between systematic and random errors and how do they effect accuracy and precision? In what circumstances would you use standard addition (versus a normal calibration curve) to determine the amount of an analyte in a sample? A urine sample, containing analyte Z is analysed by the standard addition method where 5 mL of the original sample was mixed with increasing amounts of a Z standard and each solution diluted to a volume of 50 mL prior to analysis. A plot of the final concentration of the standard in each of the 50 mL samples (x axis) versus The measured signal from the analysis of each 50 mL sample (on y axis) produced a straight line with the general equation: y = 44.72x + 4.06 what was the final concentration of Z in the 50 mL standard addition sample? what was the initial concentration of Z in the original urine sample?
An analysis of city drinking water for total hardness was done by two students in the laboratory and produced the following results (in ppm CaCO3): Student A: 228.3, 226.4, 226.9, 227.1, and 228.6. Student B: 229.5, 226.1, 230.7, 223.8, and 227.5What is the 95% confidence interval for the mean?
A pipet is used to transfer 6.00 mLmL of a 3.75 MM stock solution in flask “S” to a 25.00-mL volumetric flask “A,” which is then diluted with DI H2OH2O to the calibration mark. The solution is thoroughly mixed. Next, 10.00 mLmL of the solution in volumetric flask “A” is transferred by pipet to a 50.00-mL volumetric flask “B” and then diluted with DI H2OH2O to the calibration mark. Calculate the molarity of the solution in volumetric flask “B.”