I need the answer as soon as possible 94.llM目مقاومة دور ثاني.pdfEng. Technical College BaghdadMechatronic & Mechanical power Dept.Strength of MaterialsDate: 12/9/2021Time: 3 hoursTeacher: Dr. Raad Abdelameerالإجابة على أربعة أسئلة فقط. الدرجات موزعة بالتساري على جميع الأسئلةQ1/ A glued lap splice is to be made in a (10 mm * 20 mm) rectangular member at angle asshown in the figure below. Assuming that the shear strength of the glued joint controls thedesign. What axial force P can be applied to the member? Assume the shear strength of theglued joint to be 10 MPa.a=20°Q2/ IF a load of 1 Kip is applied to a rigid bar suspended by three wires as shown in thefigure below, what force will be resisted by each wire? the outside wires are aluminum ( E=10' psi ) the inside wire is steel (E = 30 * 10° psi) Initially , there is no slack in the wire.Alus ieQ3/ The solid 50 mm diameter steel line shaft shown in the figure is driven by a 30 -hpmotor at 3 Hz (a) find the maximum torsional stresses in section AB, BC, CD, and DE ofthe shaft.(b) determine the total angle of twist between A and E. let G = 84 GPa.30 hpbearingShp off15 hp off10 hp off1.53mm6mQ 4/ Write shear and moment equations for the beams as shown in the figure. let x be thedistance measured from left end of the beam. Also, draw shear and moment diagrams,specifying values at all change of loading positions and at points of zero shearLoadIOK20k20 KSKA.Q 5/ Calculate the moment of resistance for the I - section as shown in the figure. the valueof I= 7.36* 10* m* and maximum stress of 77 MN/ m² the web thickness is 13 mm.13mm224 mm13mmGood luck

Answered: Image /qna-images/answer/9f3beb66-d6b6-46b7-8bf8-cb6de373c0a4.jpg

QI/ A glued lap splice is to be made in a (10 mm " 20 mm) rectangular member at angle as shown in the figure helow. Assuming that the shear strength of the glued joint controls the design. What axial force P can be applied to the member? Assume the shear strength of the glued joint to be 10 MPa a=20°

QI/ A glued lap splice is to be made in a (10 mm " 20 mm) rectangular member at angle as shown in the figure helow. Assuming that the shear strength of the glued joint controls the design. What axial force P can be applied to the member? Assume the shear strength of the glued joint to be 10 MPa a=20°

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter3: Basic Theories And Math

Section: Chapter Questions

Problem 21RQ: While discussing friction in matter: Technician A says that friction creates heat. Technician B says...

See similar textbooks

Similar questions

How do a unicycle and a twoaxle car react differently to road bumps?
While discussing friction in matter: Technician A says that friction creates heat. Technician B says that friction only occurs with solids and is not present with liquids and gases. Who is correct? Technician A only Technician B only Both A and B Neither A nor B
18 - Which of the following judgments has been given incorrectly for glasses?A) Glass in molten or liquid state has a high viscosity.B) Glass is a hard and solid material to the touch.C) The main ingredient of glass is silicon dioxide.D) Viscosity of glass in liquid state at 1000 0C is higher than the densest oil.E) The viscosity increases gradually when the glass is heated and decreases gradually when it is cooled.
Which of the following consistently ranks at the top of the list of the most dangerous processes around the world? A. oil and gas production B. chemical manufacturing C. farming, logging, and fishing D. nuclear energy production
ASAB
MENG 331DYNAMICS OF MACHINERY plese answer this qustion by keypord and dont late
Five drilling machines at Al Hamriya steel is maintained by Lumina maintenance service with 2 service Engineers. The drilling machines require Maintenance at the of 20 per hour. The engineers fix machine in 2.4 mins every time it goes out of service: 1. What is the probability that no drilling machine needs service ? 2. What is the probability that all drilling machine require service at the same time ? 3. He long will a machine have to wait before it starts receiving service ? 4. What the effective arrival rate for maintenance? 5. How long will a machine have to wait before finish reserving service in the system?
Q1: Explain the significant role of Power and Free Conveyor Systems in modern manufacturing facilities. In your opinion, how the mode of control of power industrial trucks helps to handle the materials in different ways.
Can you give me a detailed description on their uses and function 1: Helmet 2: Protective clothing 3: safety shoes 4: Ear muff 5: Hand gloves 6: goggles 7: Chemical suit 8: Face mask 9: Safety harness 10: Welding shield
Q13) Exploration of oil and natural gases engineers use well drill rigs. Cutting tips of these well drill rigs should be very hard, which of the following material is recommended to use for the tip of the well drill rigs? a. Bakelite b. Silicon Nitride c. Diamond d. Aluminum Alloys
23 MENG201 Mechanical workshop practice
MECT361Mechatronics Components and Instrumentation Please solve the problem in keupord