The 8-bit registers R1, R2, R3, and R4 initially have the following values: R1 - 1111 0010, R2- 1 1 1 1 1 1 1 1 , R3- 1011 1001 , R4 1 1 101010 Determine the 8-bit values in each register after the execution of the following sequence of microoperations. R1 <-R1 + R2 R3<- R3 ^ R4, R2 <- R2 + 1 R1 <- R1 – R3
Q: 3 a) Let us assume that the CS and IP values of the base and offset of an ISR are 1210h and 1010h.…
A: The Answer to the given question is given below:
Q: 1. a)i) If CS = 020AH, SS = 0801H, SI = 0100H and IP = 1BCDH, What would be the address of the next…
A: Note: As per guidelines we are supposed to answer only one first 3-sub parts at a time .please…
Q: Assume X address is 29D, find the value of AX for each of the following instruction .Data X byte 12,…
A: Given:
Q: In this problem, you will explore processor frequency in the context of the speed of light. Suppose…
A: INTRODUCTION: Calculate the required values:Frequency(f) = 8722.78 MHz = 8.723 * 109HzClock period…
Q: Assume that your ultra-low-cost processor doesn't have the hardware budget for an integer multiplier…
A: The instruction written here is the multiplication of two numbers but not using mul op code.
Q: [b] Consider the following portion of memory with a starting address of 80000H (referenced by Val1).…
A: Here, I have to provide a solution for the above question.
Q: AR AR + BR Add BR + AR CR CR AND DR, BR BR + 1 AND DR to CR, Increment BR AR AR - CR Subtract…
A: The above question is to implement the given arithmetic operational statements in the 8-bit register…
Q: , 25% reads and 10% writes, and every other instruction type is 1 cycle. You have a 2-way set…
A: since addresses size supported by the hardware's is 40bit's total size of the main memory is 240…
Q: Suppose that DS=1000H, SS= 2000H, CS=3000H, ES=4000H, BP=FFH, BX=FFFFH and DI=5H. i. Which memory…
A: Which memory locations are addressed by: MOV DL, [BP]: the default segment of [BP] is:SS so memory…
Q: 1. Suppose the Vole memory cells from addresses 0x00 to 0x05 contain the bit patterns given in the…
A: According to the Bartelby guideline we are suppose to answer only one question at a time. Kindly…
Q: Assume the operating system for LC-3 has had new service routines added to it. Consider the…
A: q-1) Address used by the above code to access the service routine jump table is x0032 q-2) The…
Q: Q.3) Write a single 8o86 instruction to execute the following: 1) Copy the Contents of AL to Extra…
A: MCQ Type....
Q: Suppose that DS=300H, SS=200H, CS=100H, CX=AF39H, ARRAY=D3A4H, IP=5A76H, DI=245AH, SP-5489H,…
A:
Q: initially have the following values: R1 - 1111 0010, R2- 1 1 1 1 1 1 1 1 , R3- 1011 1001 , R4 1 1…
A: R1 <-R1 + R2 R1 =1111 0010 +1 1 1 1 1 1 1 1 R1= 10101010 R3<- R3 ^ R4 R3=10111001 ^ 1 1…
Q: Given that SS=2400, SP=8631H, AX=4FA6H, and DX=8C3FH. What the contents are of registers AH, DL and…
A: Given: Given that SS=2400, SP=8631H, AX=4FA6H, and DX=8C3FH. What the contents are of registers AH,…
Q: Prior to execution of the following code segment, PC was “Ox0160", WREG was "Ox08" and register Ox91…
A: The value after execution of 0x91 is 0x4D. below we explain line by line in figures:
Q: Q.3) Write a single 8086 instruction to execute the following: 1) Copy the Contents of AL to Extra…
A: Solution: 1. Python3 program for implementation 2. of Lagrange's Interpolation 3. To represent a…
Q: 3. CPU x86/8088 executes the instruction ADD AX, CX; 2byte instruction, machine code is (03-C1).…
A: Answer: I have given answered in the brief explanation
Q: What value is stored in 0x10000008 on a MIPS (big-endian) machine? Q2: What value is stored in…
A: All computers do not store the bytes that comprise a multi-byte value in the same order. Consider a…
Q: Consider the following code segment: li $s0,0 li $s1,0 li $t0, 16 loop: lw $s2, vals($s0) add…
A: This code is MIPS assembly low level code , first of all you need to see that what is MIPS code…
Q: Assume that DS=4500n, SS=2000n, BX =2100n, Sl=1486, DI 8500, BP=7814n, and AH=25n. 1-Show the PA…
A: Given Data: DS= 4500, SS= 2000, BX =2100, SI = 1486, DI = 8500, and BP = 7814 PA Location of…
Q: Consider a swapping system in which memory consists of the holes as shown in Fig.A. Note that A to I…
A:
Q: The following four questions are related to the below problem. Assume a system's memory has 32M…
A: Here in this question we have given main memory size = 32 M word Block size = 64 word Block in…
Q: 3.3 Consider a simple segmentation system that has the following segment table: Segment Starting…
A: Hey, since multiple sub parts questions posted, we will answer first three question according to our…
Q: 1. a) i) If CS = 020AH, SS = 0801H, SI = 0100H and IP = 1BCDH, What would be the address of the next…
A: CMP instructions do not change the source or destination register, only affect the flag register. i)…
Q: 3- Let a program have a portion fr of its code enhanced to run 4 times faster, to yield a system…
A: In this question, we are given enhanced speedup(SE) and overall speedup of system. And we are asked…
Q: 1. Suppose 8 bit registers have following contents X=00001111 Y=10101010 Z= 11011011 W=00110011 What…
A: The gate OR is equal to the input AND gate. The gate OR gate is the same size as the NAND gate…
Q: 2. Show how the following values would be stored by byte-addressable machines with 32-bit words,…
A: Question from computer architecture, we have to place the values as per little endian and big endian…
Q: (a) Which registers are used to access the stack ? (b) With each PUSH instruction, the stack pointer…
A: (a). Stack pointer register is the register used to access the stack.
Q: Suppose that we have a cache with the following characteristics. • Memory addresses are 8 bits wide…
A: Actually, cache memory is a fast access memory.
Q: a) In the SRAM region, what is the corresponding bit-band alias address for the bit [4] of the…
A: #define BITBAND_SRAM_REF 0x20000008 #define BITBAND_SRAM_BASE 0x22000008 #define BITBAND_SRAM(a,b)…
Q: Q3| EVALUATIONS: Memory at address 0x00100250 contains the following 16 bytes of data: 00100250 58…
A: Please find below your answer in second step:
Q: Assume that you are given the following MIPS code fragment: Label01: instruction1 instruction2…
A: suppose that the first instruction is located 10000, then the value of offset field of the…
Q: 9. If we have AX-8A3C H, CL-02 H. the result of performing SAL AX,CL is: a. C51E H c. 451E H b. E28F…
A: Answer 9) in the question option is not right the correct answer is: 28F0. explanation:
Q: Answer only 3 and 4 Suppose memory has 256KB, OS use low address 20KB, there is one program…
A:
Q: Problem Question 03 (C03) [0.5 + 0.5 = 1]: Given below are the contents of several Intel 8086…
A: Here is the answer:-
Q: we have not provided for any type of error handling, such as if the address on the address lines…
A: Given Table:
Q: Solve the following problem using Write-Invalidate and Write-Through algorithm? Given three…
A: Write Invalidate the immediate sending of the updated cache block to the other cache is not done.…
Q: In this problem, you will explore processor frequency in the context of the speed of light. Suppose…
A: INTRODUCTION: Calculate the required values:Frequency(f) = 8722.78 MHz = 8.723 *…
Q: Problem 2.3: The following have bcen executed by an 8085 Microprocessor. Write down the sequence of…
A:
Q: Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=1000H, DI=2000H, BP=3000H, IP=4000H, SI=2000H, the…
A: Given: We are given various registers with values stored in them. Register such as SS, DS, ES, CS,…
Q: Question 1: Write down the corresponding MIPS machine language of the following assembly language…
A: Given: Question 1: Write down the corresponding MIPS machine language of the following assembly…
Q: 3. Given the following sequence of instructions: Il: R1= 100 12: R1= R2+R3 13: R2= R4-25 14: R4=…
A: a. find out RAW,WAR,WAW hazard. b. rename registers prevent dependency problems , identify reference…
Q: CS=3000H, DS=5000H, ES=7000H, SS=9000H, IP=0123H, SP=1234H, BP=5678H, SI=8765H, DI=4321H. If ZF=1,…
A: ANSWER :-
Q: az) Alter exeecuting the following MIPS instructions, wbat values wilI be in registers $t6 and…
A:
Q: Prog1 request 80KB, prog2 request 16KB, Prog3 request 140KB Prog1 finish, Prog3 finish; Prog4…
A: Memory Memory is the electronic holding place for the instructions and data of a computer needs to…
Q: If CS=2000 H, DS=4000 H, SS=6000 H, ES=9000 H, BX=1358 H, BP=2122 H, SP=3500 H, SI=4100 H, DI=5147…
A: I) MOV [BX+SI+1597H], AH DS= 4000 H BX = 1358 H SI = 4100 H Since DS is used with BX 20 bit…
Q: Match segment and offsetregisters and determine their correspondingactual memory location addressed…
A: It is defined as a high-speed memory storing units. It is an element of the computer processor. It…
Q: 3.3 Consider a simple segmentation system that has the following segment table: Segment |Starting…
A: Given: A simple segmentation system with segment numbers, starting address, and the length of the…
Q: a) In the SRAM region, what is the corresponding bit-band alias address for the bit [4] of the…
A: a) In the SRAM region, what is the corresponding bit-band alias address for the bit [4] of the…
3 The 8-bit registers R1, R2, R3, and R4 initially have the following values:
R1 - 1111 0010, R2- 1 1 1 1 1 1 1 1 , R3- 1011 1001 , R4 1 1 101010
Determine the 8-bit values in each register after the execution of the following sequence of
microoperations.
R1 <-R1 + R2
R3<- R3 ^ R4, R2 <- R2 + 1
R1 <- R1 – R3
Step by step
Solved in 3 steps with 2 images
- 3) The 8-bit register AR, BR, CR, and DR initially have the following values: [5]AR = 11010110; BR = 11100111; CR = 10110001; DR = 10111010Determine the 8-bit values in each register after the execution of the following sequenceof microoperations.AR AR + BR Add BR + ARCR CR AND DR, BR BR + 1 AND DR to CR, Increment BRAR AR - CR Subtract CR from ARQ2. The 8-bit registers AR, BR, CR, and DR initially have the following values: AR= 11010010, BR= 11100011, CR= 10111001 , DR= 10101011 Determine the 8-bit values in each register after the execution of the following sequence of microoperations. AR <-AR + BR CR <- CR ^ DR, BR <- CR + 1 AR <-AR – CRThe 8-bit registers R1, R2, R3, and R4 initially have the following values: R1 - 1111 0010, R2- 1 1 1 1 1 1 1 1 , R3- 1011 1001 , R4 1 1 101010 Determine the 8-bit values in each register after the execution of the following sequence of microoperations. R1 <-R1 + R2 R3<- R3 ^ R4, R2 <- R2 + 1 R1 <- R1 R3
- 1. Suppose 8 bit registers have following contentsX=00001111Y=10101010Z= 11011011W=00110011What will be the 8 bit values of each register after execution of following sequences ofmicrooperations ?X ← ? + ?Z←Z⋀ ?, ? ← ? + 1X←X-ZThe 8-bit register AR, BR, CR, and DR initially have the following values: [5]AR = 11010110; BR = 11100111; CR = 10110001; DR = 10111010Determine the 8-bit values in each register after the execution of the following sequence of microoperations.AR AR + BR Add BR + ARCR CR AND DR, BR BR + 1 AND DR to CR, Increment BRAR AR - CR Subtract CR from ARConsider the following store instruction: SW R1, 0x000F(R0). Assume that the registers R0 and R1 are initialized with 0x00000001 and 0x53A78BC Frespectively. A section of the MIPS byte addressable data memory is shown. Give the memory word of the following memory locations after the SW operation: (a). 0x00000015. (b). 0x00000014. (c). 0x00000013. (d) 0x00000012.(e). 0x00000011. (f). 0x00000010.
- Consider the following two operations: (a) PC = PC + 4; (b) PC = PC + offset (offset is a positive or negative multiple of 4).Which of the following statements is true? a In the MIPS architecture, operation (b) is done by performing operation (a) as many times as required. b Operation (a) requires about 1/2 as much hardware to implement as does operation (b) c Operation (a) is simply done by replacing the right-most two bits of PC with 00. d Since (a) is a special case of (b), these two operations require the same hardware to implement.This question is on Computer Architecture. Translate the following arithmetic and logical expressions written in C programming language intoinstructions sequences written in MIPS Assembly language. You may assume that the values (orbase addresses) of the variables a, b, c, and d are in the general-purpose registers $s0, $s1,$s2, and $s3. 1. d[3] = a - b + c[7];2. c[5] = (a << 3) & (b >> 2);Here, <<, >>, and & indicate the bitwise left-shift, right-shift, and AND operations respectively.The 8-bit register AR, BR, CR, and DR initially have the following values:AR = 11010010; BR = 11111111; CR = 10101001; DR = 10101010Determine the 8-bit values in each register after the execution of the following sequence ofmicrooperations.AR <- AR + BR Add BR + ARCR <- CR AND DR, BR <- BR + 1 AND DR to CR, Increment BRAR <- AR - CR Subtract CR from AR
- Section 5.5 states that modern server memory modules (DIMMs) employ SEC/DED ECC to protect each 64 bits with 8 parity bits. Compute the cost/ performance ratio of this code to the code from 5.9.1. In this case, cost is the relative number of parity bits needed while performance is the relative number of errors that can be corrected. Which is better?1. Name all of the general purpose registers and some of their special functions. 2. How are the segment registers used to form a 20-bit address? 3. (a) If CS contains 03E0H and IP contains 1F20H, from what address is the next instruction fetched? (b) If SS contains 0400H and SP contains 3FFEH, where is the top of the stack located? (c) If a data segment deigns at address 24000H, what is the address of the last location in the segment? 4. Explain what the instruction array and data caches are used for. 5. What is the EU and BIU, and what purpose in the microcomputer? 6. Two memory locations, beginning at address 3000H, contain the bytes 34H and 12H. What is the word stored at location 3000H? See Figure 2.26 for details. Address 3000 Data 34 3001 12 Figure 2.26 For question 6 7. What is a physical address? What are the differences between the 8086 logical and physical memory maps? 8. May memory segments overlap? If so, what is the minimum number of overlapped bytes…Answer only 3 and 4 Suppose memory has 256KB, OS use low address 20KB, there is one program sequence: (20) • Prog1 request 80KB, prog2 request 16KB, • Prog3 request 140KB • Prog1 finish, Prog3 finish; • Prog4 request 80KB, Prog5 request 120kb • Use first match and best match to deal with this sequence • (from high address when allocated) • (1)Draw allocation state when prog1,2,3 are loaded into memory? • (2)Draw allocation state when prog1, 3 finish? • (3)use these two algorithms to draw the structure of free queue after prog1 , 3 finish(draw the allocation descriptor information,) • (4) Which algorithm is suitable for this sequence ? Describe the allocation process?