The line currents in a delta-connected load are I = 5/0°, I, = 7/200°, and I. = 5/90° A. Calculate the positive-, negative-, and zero-sequence components of the current for phase a. Also determine the positive- and negative-sequence components of current Iab and hence calculate Iab.

The line currents in a delta-connected load are I = 5/0°, I, = 7/200°, and I. = 5/90° A. Calculate the positive-, negative-, and zero-sequence components of the current for phase a. Also determine the positive- and negative-sequence components of current Iab and hence calculate Iab.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.22MCQ: In a balanced three-phase Y-connected system with a positive-sequence source, the line-to-line...

See similar textbooks

Related questions

Q: An unbalanced three-phase wye-connected and grounded load is connected to a balanced three- phase…

A: It is given that an unbalanced three-phase wye-connected and grounded load is connected to a…

Q: 18.) A 30-km, 34.5 kV, 60 Hz three-phase line has a positive-sequence series impedance z = 0.25 +…

A: The transmission line is a long conductor with a specific design (bundled) for transporting large…

Q: Figure shows the one-line diagram of a simple three-bus power system with generation at buses 1 and…

Q: b) The one-line diagram for a simple power system is given in Figure 1(b). į. Draw the impedance…

Q: The equivalent circuit of a single phase short transmission line is shown in Figure Q4(b). Here, the…

Q: In a three phase overhead system , each line is suspended by a string of three insulator. The…

Q: J-RV, J-HZ compensated kample 6.2A 400-Km, as a positive-sequence series impedance z = 0.03 + j0.35…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: Under Unbalanced Condition Without Faults: a. Load Line Currents (Ia, Ip,I); b. Load Line Voltages…

A: We are authorized to answer three subparts at a time. Since you have not mentioned which part you…

Q: Q1. What is the necessity of maintaining phase sequence? Suppose there are three loads connected at…

A: Given data: VR=1200 VVL=2400 VVC=2400 V

Q: Figure below shows the one-line diagram of a three-phase power system. By selecting a common base of…

Q: In a three-phase system voltage, assume that the phase-to-neutral voltage at phase “b” is considered…

A: 1. The positive sequence is the same sequence of phasor in which power is generating or winding has…

Q: Given the symmetrical components to be VO = 10<0 V , V1 = 80<30 V , V2 = 40<-30 V determine the…

A: Symmetrical components: A system of three unbalanced phasors can be resolved in the following three…

Q: i. Some reasons for adopting high transmission line voltages are to improve -------and the…

A: Given that three fill in the blanks related to high transmission line voltages .

Q: Given the symmetrical components to be V0 = 10<0 V , V1 = 80<30 V , V2 = 40<-30 V determine…

A: ( ) Va = V0 + V1 + V2. Vb = V0 + (a^2)V1+(a)V2. Vc = V0 + (a)V1+(a^2)V2. Here, \(a = e^{i2\pi/3}\)…

Q: 3. A 210-km, 192-KV, 60 Hz three-phase line has a positive-sequence series impedance z= 0.06+j0.4…

A: The data given in the question are:…

Q: Determine the node voltages after one iteration for the single-phase lateral shown in the figure.

Q: iv) Draw a single-phase equivalent circuit of the system. v) Calculate the following line currents,…

Q: For the 3-phase system shown below, the source line voltage is 460 V, 60 Hz, 1). Phase "a" voltage,…

A: In the question, A three phase system given as shown in the figure find the each phase voltage and…

Q: A balanced three phase voltage of 360-V line-to-neutral is applied to a balanced Y-connected load…

A: Given data: Zs=j24 ΩZm=j6 Ω

Q: 2. A 3-phase, 75 MVA, 11-8 kV star-connected alternator with a solidly earthed neutral point has th…

A: As per Bartleby guidelines we are allowed to solve only one question,please ask the rest again.

Q: A three-phase ring main distributor ABCD, fed from point A and supplies balanced loads as follows:…

A: Distribution network connected in a form of a ring is a ring distribution network in which one…

Q: 1. Use Gauss-Siedel iterative method to find V2, perform one iteration 2. If V2-0.98 pu, find the…

A: The Gauss-Seidel technique, commonly known as the Liebmann method or the method of successive…

Q: 1. A 3-phase overhead transmission line has a total series impedance per phase of 200 Z80° ohms and…

A: 3 phase overhead voltage, series impedance and shunt admittance given. Line voltage 220KV and power…

Q: : Consider star-delta system, the source is a positive sequence with Van = 120LO V and phase…

A: According to question we have to calculate the value of VL and IL.

Q: 2- The Purpose of using Unbalanced Three-phase Systems: Jji

A: Actually we are not intentionally use the unbalanced system. Unbalanced system created due to the…

Q: c) Referring to Figure 4, assume that there is a 300 MVA load at 0.8 lagging power factor at 132 kV…

A: Length of transmission line = 100 km it is medium transmission line. We use nominal pi network to…

Q: The real and reactive power of slack bus are determined after the power flow analysis. Select one:…

A: There are three types of bus in power system, namely, Slack bus Generation bus Load bus

Q: Calculate magnitudes and angles for the line currents IaA, IbB, and IcC.

Q: 1. what do you understood about DELTA connection? 2. What are the relationships between the Line…

A: There are 2 main types of 3 phase wiring connections Star connection Delta connection Delta…

Q: For the Δ - Δ circuit, calculate the phase and line currents.

A: to find the current

Q: TUTORIAL PROBLEMS 1. A 3-phase overhead transmission line has a total series impedance per phase of…

A: The solution can be achieved as follows.

Q: A single-line diagram of a three-phase balanced system is given below. A bolted three- phase short…

A: The single line diagram of a Three phase balanced system is given above:where, operating voltage=21…

Q: NOTE :( Just solve only for the Symmetrical components of the corresponding phase voltage) Given…

A: Given the symmetrical components to be V0=10∠0 V, V1=80∠30 V, V2=40∠-30 V, a) for unbalanced phase…

Q: The bus impedance matrix for a three-bus power system has per-unit elements as: Z11 = 0.5 Z12 = 0.4…

A: In this question we need to find a subtransient fault current when a 3 phase fault occur at bus 3.

Q: 3-phase, overhead transmission line has a total series impedance per phase of 200 ohms and a total…

A: In this question , we will find sending end line voltage and current by Rigorous method........

Q: The one line diagram of a three phase power system is as shown in Figure 7 Impedances are marked in…

Q: A balanced three-phase source with grounded neutral has line-to-neutral voltages of 230 volts with…

Q: 1. A delta connected load with impedance 20cis0- ohms per phase is supplied from a 220 volts, 60…

Q: Refer to the 5-bus data given below. Sbase = 400 MVA, the base voltage is 15.0 kV for buses 1 and 3,…

A: a) Single line diagram of given power system here series parameter are in impedance and shunt…

Q: In a 3-phase overhead system, each line is suspended by a string of 3 insulators. The voltage across…

A: Given three phase overhead system , each line is suspended by a string of 3 insulators The voltage…

Q: A three-phase 630 kV, 50 Hz, 400 km completely transposed long transmission line, has the following…

A: Given values are =

Q: A balanced 3 phase load of 30 MW is supplied at 132 KV , 50 Hz and 0.85 pf lagging by means of…

A: A balanced 3 phase load Power=30 MWVoltage= 132 kV Power factor=0.85 series Impedance of a single…

Q: of 0.1+j0.2 Ω, connected through transmission lines with the impedance of 0.5+j1 Ω to a load with…

A: After doing all the calculations of a, b and c considering two decimal points d and e can be…

Q: Line impedances for the power system shown in Figure 1 are Z12 = Z23 = 3.0 + j40.0 Ω, and Z24 = 6.0…

A: Any obstacle or measurement of the resistance of an electric current to the energy flow when voltage…

Q: 2. A 200-km, 230-kV, 60-Hz three-phase line has a positive-sequence series impedance z = 0.07 +…

A: To transmit the power over the long distance, power transmission lines are use .it can be overhead…

Q: Q3) A balanced 3-phase load of 30 MW is supplied at 132 kV, 50 Hz and 0-85 p.f. lagging by means of…

Q: For the power system its one line diagram is shown below: 1-Draw the reactance diagram for power…

Q: The parameters of a three-phase line 200 km long are resistance/km =0.15 , inductive/km=0.5 and…

Q: 1. A 3-phase overhead transmission line has a total series impedance per phase of 200 280° ohms and…

A: A 3 phase overhead transmission line Total series impedance Z= 200∠ 80 ohm Shunt admittance…

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

100%

The line currents in a delta-connected load are I.
5/0°, 1, = 7/200°, and I. = 5/90° A. Calculate the
positive-, negative-, and zero-sequence components of the current for phase a. Also determine the
positive- and negative-sequence components of current Iab and hence calculate Iah.
Ans. 5.57/-15° A; 7.94/224° A; 0; 3.21/15° A; 4.59/-166° A; 1.38 A

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In a balanced three-phase Y-connected system with a positive-sequence source, the line-to-line voltages are 3 times the line-to-neutral voltages and lend by 30. (a) True (b) False
A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of 0.15/km, a per-phase inductance of 1.3263 mH/km, and negligible shunt capacitance. Using the short line model, find the sending-end voltage, voltage regulation, sending-end power, and transmission line efficiency when the line is supplying a three-phase load of (a) 381 MVA at 0.8 power factor lagging and at 220 kV and (b) 381 MVA at 0.8 power factor leading and at 220 kV.
A balanced three-phase load is connected to a 4.16-kV, three-phase, fourwire, grounded-wye dedicated distribution feeder. The load can be mode led by an impedance of ZL=(4.7+j9)/phase, wye-connected. The impedance of the phase conductors is (0.3+j1). Determine the following by using the phase A to neutral voltage as a reference and assume positive phase sequence: (a) Line currents for phases A, B, and C. (b) Line-to-neutral voltages for all three phases at the load. (c) Apparent. active, and reactive power dissipated per phase, and for all three phases in the load. (d) Active power losses per phase and for all three phases in the phase conductors.
The 500-kV, 60-Hz, three-phase line in Problems 4.20 and 4.41 has a 180-km length and delivers 1600 M W at 475 kv and at 0.95 power factor leading to the receiving end at full load. Using the nominal circuit, calculate the (a) ABCD parameters, (b) sending-end voltage and current, (c) sending-end power and power factor, (d) full-load line losses and efficiency, and (e) percent voltage regulation. Assume a 50C. conductor temperature to determine the resistance of this line.
A Y-connected load bank with a three-phase rating of 500 kVA and 2300 V consists of three identical resistors of 10.58. The load bank has the following applied voltages: Vab=184082.8,Vbc=276041.4, and Vca=2300180V. Determine the symmetrical components of (a) the line-to-line voltages Vab0,Vab1, and Vab2, (b) the line-to-neutral voltages and Van0,Van1, and Van2, (c) and the line currents Ia0,Ia1, and Ia2. (Note that the absence of a neutral connection means that zero-sequence currents are not present.)
Determine the bus admittance matrix (Ybus) for the three-phase power system shown in Figure 6.23 with input data given in Table 6.11 and partial results in Table 6.12. Assume a three-phase 100 MVA per unit base. TABLE 6.11 Bus input data for Problem 6.20 TABLE 6.12 Partially Completed Bus Admittance Matrix (Ybus) for Problem 6.30
Consider a long radial line terminated in its characteristic impedance Zc. Determine the following: (a) V1/I1, known as the driving point impedance. (b) | V2 |/V1|, known as the voltage gain, in terms of al. (c) | I2 |/| I1 |, known as the current gain, in terms of al. (d) The complex power gain, S21/S12, in terms of al. (e) The real power efficiency, (P21/P12)=, terms of al. Note: 1 refers to sending end and 2 refers to receiving end. (S21) is the complex power received at 2; S12 is sent from 1.
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
A 3-phase overhead transmission line delivers a load of 80 MW at0.8 p.f. lagging and 220 kV between the lines. Its total seriesimpedance per phase and total shunt admittance per phase are 200ohms with an angle of 80 degrees and 0.0013 mho with an angle of90 degrees per phase respectively. Using nominal-T method,determine the following:(i) A, B, C, D constants of the line(ii) Sending end voltage(iii) Sending end current(iv) Sending end power factor(v) Transmission efficiency of the line
Note that the given 25 kV L-L voltage appears across the loads (right side of ZL) as denoted by Vab, Vbc, and Vca. Since there is no given voltage angle, you may assign angle zero to one of the line-to-neutral voltages. 1. Without the capacitors, what is the magnitude of the current passing through the line impedance ZL?
A balanced, star connected three-phase system is directly connected to an unbalanced load, with a solid neutral connection. The line-to-neutral voltage Van on the load side and per phase load impedances (i.e., Za, Zb and Zc) are as below: ?an = 240∠0 ? ?? = 10 + 3? Ω ?? = 16 + 3? Ω ?? = 10 + 3?Ω Draw the circuit diagram and calculate the sequence currents and neutral current
Refer to the 5-bus data given below. Sbase = 400 MVA, the base voltage is 15.0 kV for buses 1 and 3, and 345 kV for buses 2, 4, 5. Note that 1-5 and 3-4 are 15/345 kV transformers.a) Draw a one-line diagram of the power system.b) Find the elements Y23, Y43, Y11 Y33 of the system bus admittance matrix.