The material used for section CB of the shaft shown has an allowable shear stress of Tallow= 75 MPa. If Ic = TB = 4300 N-m in the directions shown in the figure. Determine the largest inside radius (rin) the shaft can have at Section a-a, if the outside radius is 40 mm. Express your answer in mm to the nearest 0.1 mm. 600 N•m Tin T 40 mm TB B Section a-a 600 N•m

The material used for section CB of the shaft shown has an allowable shear stress of Tallow= 75 MPa. If Ic = TB = 4300 N-m in the directions shown in the figure. Determine the largest inside radius (rin) the shaft can have at Section a-a, if the outside radius is 40 mm. Express your answer in mm to the nearest 0.1 mm. 600 N•m Tin T 40 mm TB B Section a-a 600 N•m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the maximum shear stress acting at a tubular cross-section having an outer diameter D, = 100 mm and inner diameter D; = 80 mm, if the applied torque T = 500 N.m. Take ) = 5.79624 x 108 m?; Select one: O 431MPa O 2.15MPa O 6.15MPa O 1032MPa O 8.62MPa
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the shear stress (in Pa) in the hollow shaft using the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 70092104 Pa and angle of twist of 2.25ᴼ for the whole shaft. Use G = 83000000000 Pafor the shaft, x = 2.43 m, and y = 1.89 m. Round off the final answer to two decimal places.
A 0.2 m diameter shaft is supported by a smooth journal bearing at E and a smooth thrust bearing at F. Determine the maximum shear stress developed in segment AB of the shaft. 26.63 MPa 19.01 MPa 12.73 MPa 52.25 MPa
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the shear stress in the solid shaft (in Pa) using the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 70041051 Pa and angle of twist of 2.3ᴼ for the whole shaft. Use G = 83000000000 Pafor the shaft, x = 2.47 m, and y = 1.62 m. Round off the final answer to two decimal places.
The shaft consists of three concentric tubes, each made from the same material and having inner and outer radii as given below. Length of shaft is 2m. One end is fixed to the wall and to the other end a disc is attached. If a torque of T =800 N.m is applied at the disc end, determine the maximum shear stress in the shaft. 1. Inner tube: r; = 20mm, r, = 25 mm 2. Center tube: r; = 26 mm, r. = 30 mm 3. Outer tube: r = 32mm, r, = 38mm
The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 80 lb-ft/ft along its entire length. Using a = 2.5 ft, b = 4.0 ft, and c = 8.5 ft, determine(a) the maximum shear stress in the pipe.(b) the rotation angle φC at the free end of the shaft.
The shaft is hollow from A to B and solid from B to C. Determine the maximum shear stress in the shaft. The shaft has an outer diameter of 80 mm, and the thickness of the wall of the hollow segment is 10 mm.
Consider a tube having a rectangular cross-section as shown below. The tube is subject to two twisting moments of 70 N - m . Determine the average shear stress developed at point A. The tube is fixed at the other end. a) 1.75 MPa b) -1.65 MPa c) 4.086 MPa d) 2.095 MPa If your doing it fast, I will rate you...
The drive shaft AB of an automobile is to be designed as a thin-walled tube. The engine delivers 150 hp when the shaft is turning at 1000 rev>min. Determine the minimum thickness of the shaft’s wall if the shaft’s outerdiameter is 2.5 in. The material has allowable shear stress of tallow = 7 ksi.
The shaft is used to transmit 30 hp while turning at 600 rpm. Determine the maximum shear stress in the shaft. The segments are connected together using a fillet weld having a radius of 0.18 in.
The drive shaft AB of an automobile is made of a steel having allowable shear stress of tallow = 8 ksi. If the outer diameter of the shaft is 2.5 in. and the engine delivers 200 hp to the shaft when it is turning at 1140 rev>min, determine the minimum required thickness of the shaft’s wall.
Q3: The shaft consists of three concentric tubes, each made from the same material and having inner and outer radii as given below. Length of shaft is 2m. One end is fixed to the wall and to the other end a disc is attached. If a torque ofT =800 N.m is applied at the disc end, determine the maximum shear stress in the shaft. 1. Inner tube: r¡ = 20mm, r, = 25 mm 2. Center tube: r; = 26 mm, r, = 30 mm 3. Outer tube: r; = 32mm, r, = 38mm