The maximum solid solubility of carbon in ferrite occurs at 0.022 wt% C and 727 ° C, the eutectoid composition is 0.76 wt% C, the maximum solid solubility of carbon in austenite occurs at 2.14 wt% C and 1147 ° C, and the cementite composition is 6.7 wt% C. For 2122 g of a 3.2134 wt% C steel at 726 ° C, what will be the mass of carbon present as part of a compound? (a) 67.9 g (b) 74.2 g (c) 58.7 g (d) 83.5 g

The maximum solid solubility of carbon in ferrite occurs at 0.022 wt% C and 727 ° C, the eutectoid composition is 0.76 wt% C, the maximum solid solubility of carbon in austenite occurs at 2.14 wt% C and 1147 ° C, and the cementite composition is 6.7 wt% C. For 2122 g of a 3.2134 wt% C steel at 726 ° C, what will be the mass of carbon present as part of a compound? (a) 67.9 g (b) 74.2 g (c) 58.7 g (d) 83.5 g

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter22: Inorganic Materials

Section: Chapter Questions

Problem 7P

See similar textbooks

Similar questions

A 1.1324 g sample of magnetite ore was dissolved in concentrated HCl to give a solution that contained a mixture of Fe2+ and Fe3+. Nitric acid was added and the solution was boiled for a few minutes, which converted all of the iron to Fe3+. The Fe3+ was then precipitated as Fe2O3*xH2O by addition of NH3. After filtration and washing, the residue was ignited at a high temp to give 0.5394 g of pure Fe2O3. What is the percent Fe and the percent Fe3O4 in the sample?
World production of chromite (FeCr₂O₄), the main ore ofchromium, was 1.5107metric tons in 2003. To isolate chro-mium, a mixture of chromite and sodium carbonate is heated inair to form sodium chromate, iron(III) oxide, and carbon diox-ide. The sodium chromate is dissolved in water, and this solutionis acidified with sulfuric acid to produce the less soluble sodiumdichromate. The sodium dichromate is filtered out and reduced with carbon to produce chromium(III) oxide, sodium carbonate,and carbon monoxide. The chromium(III) oxide is then reduced to chromium with aluminum metal. (a) Write balanced equations for each step. (b) What mass of chromium (in kg) could be pre-pared from the 2003 world production of chromite?
Chalcopyrite (CuFeS2), is an important source of copper. A typical chalcopyrite ore contains about 0.75% Cu. What volume of sulfur dioxide at 25ᵒC and 1 atm pressure is produced when one boxcar load ( 4 x 10^3 cu.ft) of chalcopyrite ore (density = 2.6 g/cu.cm) is roasted? Assume all the sulfur in the ore is converted to SO2 and no other source of sulfur is present.
For the alloy Mg-45 wt% Pb alloy at 500 C, what is the weight percentage of Pb in liquid?
Impure nickel, refined by smelting sulfide ores in a blast furnace, can be convertedinto metal from 99.90% to 99.99% purity by the Mond process. The primaryreaction involved in the Mond process is:Ni(s) + 4CO(g) ⇌ Ni(CO)4(g)In the second step of the Mond process, the gaseous Ni(CO)4 is isolated andheated to 227°C. The purpose of this step is to deposit as much nickel as possibleas pure solid (the reverse of the preceding reaction). Calculate the equilibriumconstant for the preceding reaction at 227°C.
chalcopyrite (cufes2) is an important ore contains about 0.75% cu. what volume of sulfur oxide at 25 c and 1atm pressure is produced when one boxcar load (4x10^3 ft^3) of chalcopyrite ore (density = 2.6 g/cm^3) is roasted? assume all the sulfur in the ore is converted to so2 and no other source of sulfur is present.
If you are given a fully labeled hypoeutectoid TTT diagram and the associated Fe-C phase diagram, is it possible to determine the average composition of the Fe-C alloy? If so, how?
To each digestion flask 200 mL aliquots of 10 different drinking water samples were added. Silver was extracted by a co-precipitation procedure and collected by filtration. The precipitate was digested in 200 μl hot concentrated nitric acid and diluted to 5 mL in a dilute phosphate solution. Standards were prepared according to the following table. The samples were analyzed by graphite furnace AAS. Calculate the concentration of silver in each sample. Are there any problems? How will you address each of the identified problems?
Describe, with using necessary diagrams, the structure and/or microstructure of the following materials and justify their applications based on their properties. Plain carbon steel (0.25% C), as used to make a body panel for a car Duraluminum 2024: as used to make aircraft structures High density polyethylene (HDPE), as used to make non-carbonated drinks containers Silicon carbide, as used in ball type flow control valves Carbon fibre reinforced polymer (CFRP), as used in the construction of high-end automobile racing
What volume of sulfur dioxide at 25ᵒCand 1 atm pressure is produced when one boxcarload ( 4 x 10^3 cu.ft) of chalcopyrite ore (density =2.6 g/cu.cm) is roasted? Assume all the sulfur inthe ore is converted to SO2 and no other source ofsulfur is present.
In determining the manganese dioxide content of a pyrolusite mineral. A sample of 0.5261 g of pyrolusite was treated with 0.7149 g of 97.98% sodium oxalate in an acid medium. After the reaction was complete, 30.47 mL of a 0.02160 M potassium permanganate solution was required to titrate for excess unreacted oxalic acid. Calculate the percentage of manganese dioxide in the pyrolusite.
GRAVIMETRIC ANALYSIS The addition of dimethylglyoxime, H2C4H602N2, to a solution containing nickel(Il) ion gives rise to a precipitate: Nickel dimethylglyoxime is a bulky precipitate that is inconvenient to manipulate in amounts greater than 135 mg. The amount of nickel in a type of permanent-magnet alloy ranges between 22% and 38%. Calculate the sample size that should not be exceeded when analyzing these alloys for a nickel.