The sulfate in a247.1 mg sample was precipitated as BasO4 by addition of 25.00 mL of 0.03992 M BaCl2. The precipitate was removed by filtration and the remaining BaCl2 consumed 36.09 mL of 0.0217 M EDTA for titration to the Camalgite endpoint. Calculate the % SO3 in the sample.
Q: 2.054 g of macrogol monostearate (average molecular weight 706. 5) was added to a 200 ml flask and…
A: Solution: We know the saponification reaction i.e the base catalysed hydrolysis reaction of an ester…
Q: A 3650-mg sample containing bromate and bromide was dissolved in sufficient water to give 250.0 mL.…
A:
Q: . Titration of Ca²+ and Mg²+ in a 50.00-mL hard water sample required 23.65 mL of 0.01205 M EDTA. A…
A: A question based on environmental pollution that is to be accomplished.
Q: When treated with a solution of ammonium sulfate an unknown solution produced heavy white…
A: The above procedure is carried out to identify unknown solutions.
Q: A 2.00 mL sample of commercial bleach was diluted with water to a 100.00 mL volumetric flask. A…
A: The ratio of mass of solute in 100 mL of solution is known as %w/v
Q: A carbonate fusion was needed to free the Bi from a 0.6400-g sample containing the mineral eulytite…
A: Given, Bi3+ + H2PO4- →BiPO4(s) + 2H+ mass of eulytite sample = 0.64 g molarity of NaH2PO4 = 0.0340 M…
Q: An unknown solution containing 25.00 mL of Ni2* in dilute HCI is treated with a known excess of…
A: Introduction : This question is basically based on back titration concept . Given : Molarity of…
Q: A foot powder sample containing Zn was dissolved on 50.00 mL water and was titrated to the end point…
A:
Q: 2. A standard solution of EDTA is prepared, and by titration each ml is found to complex with the Mg…
A:
Q: A 30-mL portion of a solution containing Ca2+ and Mg2+ was titrated with 28.19 mL of 0.213 M EDTA at…
A: Complexometric titration with EDTA is used for the determination of metal ions line calsium and…
Q: 100 mL of mineral water containing Mg2+ and Ca2+ is taken and titrated with 86.65 mL of 0.06120 M…
A: We know that EDTA forms 1:1 complex with metals Mg+2 and Ca+2 Initial moles of EDTA = M*V =…
Q: A 1.0 g sample containing urea was dissolved in water and diluted in a 100.00 mL volumetric flask.…
A: On reaction with sulphuric acid, urea produces ammonia. One mole of urea produces one mole of urea.…
Q: A carbonate fusion was needed to free the Bi from a 0.6400-g sample containing the mineral eulytite…
A: This is a complexometric titration.
Q: 10.0 ml sample of Mg2+ and Nat mixture was titrated against 0.02 M EDTA. It is required 20.0 ml of…
A:
Q: A 5.186 gram sample of the anti-malarial pesticide DDT was dissolved in 100.0 mL of alchohol and…
A: The structure of DDT is as shown below: One molecule of DDT has 5 atoms of Cl.
Q: A batch of codeine phosphate powder was analysed according to the BP (1999) method described below.…
A: The amount of codeine phosphate, C18H21NO3.H3PO4(s) is quantitatively determined by non-aqueous…
Q: A foot powder sample containing Zn was dissolved on 100.00 mL water and was titrated to the end…
A: The question is based on the concept of complexometric titrations. We have to calculate pZn value.
Q: 5.0g of an alloy of copper was dissolved in one litre of dilute sulphuric acid. In 20 ml of this…
A: The reaction is written as 2Cu2++2I-⇌2Cu2++I2 and 2Na2S2O3+I2⇌Na2S4O6+2NaI From the reaction it can…
Q: What weight of strontium acetate containing 99% Sr(CH3COOH)2.½H2O must be used as sample in an assay…
A: Solution -
Q: A 100mLSolution containing 0.145g of NiCl2 was supplied in the lab. Students were advised to use 5mL…
A: The density of solution = 1g/mL Mass of precipitate = 0.0291 g and 0.0353 g A 100mLSolution…
Q: What are the primary standard substances used in the adjustment of thiosulfate solutions? b.) When…
A: The question is based on the concept of iodometric titration. it is an indirect titration of iodine…
Q: Calculate the gravimetric factor of the following. 2 Fe3O4 is sought(Analyte), 3 Fe2O3 is weighed…
A: Given, Sought : Fe3O4 Precipitate : Fe2O3
Q: A 100.0 mL sample of drinking water was buffered at pH 10.0 and, after addition of Calmagite…
A:
Q: A 10.0 mL sample containing Fe³⁺ and Cu²⁺ was diluted to 100.0 mL solution. A 20.0 ml aliquot…
A: In EDTA titration, a masking agent is defined as a reagent that prevents one of the analyte from…
Q: A 500.0mg of butter was warmed and shaken vigorously with water. The undissolved material was…
A: A Volhard method is an inorganic quantitative analytic method in which an indirect or back titration…
Q: A mineral in a fine state of division (0.6324 g) was dissolved in 25.0 mL of 4.0 mol / L boiling HCl…
A:
Q: An aqueous solution of 0.2100 g of a mixture containing potassium cyanide and potassium chloride…
A: Given that - Mass of mixture of potassium cyanide, KCN and potassium chloride , KCl = 0.2100 g…
Q: 1. The thiourea in a 1.455 g sample of an organic material was extracted into a dilute H2SO,…
A: Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: A 30-mL portion of a solution containing Ca²+ and Mg2+ was titrated with 28.19 mL of 0.207 M EDTA at…
A: Given that, In the first titration Volume of Ca-Mg solution = 30 mL Volume of EDTA used = 28.19 mL…
Q: The distribution constant, Kp, for compound A between toluene and water is 9.65. What is the…
A:
Q: Chromel is an alloy composed of nickel, iron, and chromium. A 0.6392-g sample was dissolved and…
A:
Q: Caustic potash that has been exposed to air is found on analysis to contain 90.00% KOH, 2.38% K2CO3…
A:
Q: A foot powder sample containing Zn was dissolved on 50.00 ml water and was titrated to the end point…
A:
Q: Analyze and calculate the percentage of nickel in a 1.201 grams sample of nickel ore which was…
A: Ni2+(aq) reacts with CN-(aq) through the reaction below: Ni2+(aq) + 4CN-(aq) (Excess) ---->…
Q: Triplicate samples of NaOH was found to have concentrations of 0.1444 M (Trial 1), 0.1107 M (Trial…
A: Introduction : Titration can be defined as the technique where a solution of known concentration is…
Q: Excess solid Ni(OH)2 was added to water and the resulting solution was allowed to stand for several…
A: In order to find Ksp, we need dissociation equation of Ni(OH)2(s) and equation for reaction with…
Q: 5. 0.1500 g sample of chromium ore was dissolved and the chromium oxidized to chromate ion. The…
A: Answer: This question is based on the stoichiometric calculation where we have to convert the number…
Q: Titration of 50.00 mL of 0.04715 M Na2C2O4 required 39.25 mL of a potassium permanganate solution.…
A: Given, Volume of Na2C2O4 = 50.00 mL Concentration of Na2C2O4 = 0.04715 M…
Q: A 0.6025 g sample was dissolved and the Ca2+ and Ba2+ ions present were precipitated as BaC2O4.H2O…
A:
Q: A foot powder sample containing Zn was dissolved on 200.00 mL water and was titrated to the end…
A:
Q: A 0.3045 g of CaCO3 primary standard was dissolved using concentrated HCl, evaporated to incipient…
A: Given, 0.3045 g of CaCO3 dissolved in concentrated HCl Dilute to 250 mL Molar mass of CaCO3 =…
Q: When treated with a solution of ammonium sulfate an unknown solution produced heavy white…
A: The ions present in the unknown solution has to be given,
Q: Chromel is an alloy composed of nickel, iron, and chromium. A 0.6418-g sample was dissolved and…
A: The 0.6418 g sample contains three metals: nickel, iron, and chromium. This total sample is…
Q: A 0.4020 g sample was dissolved, and Ca2+ and Ba2+ ions present were precipitated as Ba.C2O4.H2O and…
A:
Q: The calcium content of a milk sample was to be determined by EDTA titration. A sample weighing 0.206…
A:
Q: A water sample was tested for hardness. To titrate Ca2* and Mg2+, a 25.00-mL sample needed 7.39 ml…
A:
Q: A standard CaCO3 solution is prepared by dissolving 0.4193g in enough dilute HCl to effect solution…
A: The given data contains, weight of CaCO3 =0.4193 g volume of EDTA =23.62 ml
Q: The amount of iron in a meteorite was determined by a redox titration using KMnO4 as the titrant. A…
A:
Q: The Ksp values of two solid carbonates, A2CO3 and BCO3, were determined by preparing 250.0-mL…
A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…
The sulfate in a247.1 mg sample was precipitated as BasO4 by addition of 25.00 mL of 0.03992 M BaCl2. The precipitate was removed by filtration and the remaining BaCl2 consumed 36.09 mL of 0.0217 M EDTA for titration to the Camalgite endpoint. Calculate the % SO3 in the sample.
Step by step
Solved in 6 steps
- A 500.0mg of butter was warmed and shaken vigorously with water. The undissolved material was removed by filtering and the aqueous portion was made 1.0M in HNO3 and 0.025M in Fe(NO3)3. This acidified solution was treated with 10.00ml of 0.1755M AgNO3 to precipitate the chloride ion and, after the addition of a small amount of nitrobenzene, 14.22ml of 0.1006M KSCN was required to back titrated the excess Ag+. Calculate the % NaCl in the butter.A 30-mL portion of a solution containing Ca2+ and Mg2+ was titrated with 28.19 mL of 0.213 M EDTA at pH 10. Another 30-mL aliquot of the same Ca-Mg mixture was treated with NaOH to make the solution strongly alkaline and precipitate Mg(OH)2. This solution was then titrated with the same EDTA solution. What would be the required EDTA volume (in mL) to reach the endpoint of the second aliquot if it was found that there was 0.061 M of Mg2+ in the sample?A solid containing tris was dissolved in water and brought to a total volume of 50.00 ml. A 10.00 ml aliquot of the solution was titrated with 0.09978 M HCl to a bromcresol green endpoint. The aliquot consumed 38.93 ml of titrant. Calculate the weight of tris in the original sample.
- A 0.3045 g of CaCO3 primary standard was dissolved using concentrated HCl, evaporated to incipient dryness, and quantitatively transferred to a 250 mL volumetric flask and diluted to mark. A 10 mL of aliquot was then transferred to an Erlenmeyer flask, together with 5mL buffer and 5 drops of EBT indicator, and was used to standardize the EDTA titrant. The solution turned blue after the addition of 24.10 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. [Analysis] A 30 mL unknown water sample was treated with 37.6 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. What is the concentration of Ca2+ (40.0780 g/mol) in ppm?A carbonate fusion was needed to free the Bi from a 0.6400-g sample containing the mineral eulytite (2Bi2O3. 3SiO2). The fused mass was dissolved in 25.00 mL dilute acid, following which the Bi3+was titrated with 27.00mL of 0.03400M NaH2P04. The reaction is Bi3++ H2PO4-BiPO4(s) + 2H+ Identify: (a) possible chemical indicator for this analysis (b) Calculate the weight percent purity of eulytite (FW=1112.17g/mol) in the sample.Caustic potash that has been exposed to air is found on analysis to contain 90.00% KOH, 2.38% K2CO3 and 7.62% H2O. What weight of residue will be obtained if 1.00 g of this sample is added to 46.00 mL of 1.00 N HCl and the resulting solution, after neutralization with 1.070N KOH is evaporated to dryness?
- 250.0 ml of the mineral water sample was precipitated with potassium sodium tetraphenyl bromate: K+ + B(C6H5)4- KB(C6H5)(s). The precipitate was filtered, washed and dissolved in an organic solvent. An excess of HgY2- was added to the solution: 4 HgY2- + B(C6H5)4- +4H2O H3BO3 + 4C6H5Hg+ + 4HY3- + OH-. The liberated EDTA was titrated with 0.05581 M Mg 2+ solution, which consumed 29.64 mL. Calculate the potassium concentration [mg/l] in the sample.1.) A 0.1278-g sample of primary standard Na2C2O4 required exactly 60.04 mL of permanganate solution to reach the end point. What is the molarity of the KMnO4 reagent? 2.) A 50.00 mL sample containing La3+ was added with sodium oxalate to precipitate La2(C2O4)3, which was washed, dissolved in dilute H2SO4, and titrated with 18.09 mL of the standard KMnO4 solution (in #1). Calculate the molarity of La3+ in the unknown sample.A 0.3045 g of CaCO3 primary standard was dissolved using concentrated HCl, evaporated to incipient dryness and quantitatively transferred to a 250 mL volumetric flask, and diluted to mark. A 10 mL of aliquot was then transferred to an Erlenmeyer flask, together with 5mL buffer and 5 drops of EBT indicator, and was used to standardize the EDTA titrant. The solution turned blue after the addition of 24.10 mL of EDTA. A blank correction was performed and was determined to be 0.4 mL. What is the concentration of EDTA obtained (MW CaCO3 = 100.0869 g/mol)?
- A mixture containing only KCl and NaBr is analyzed by the Mohr method. A 0.2125-g sample is dissolved in 25 mL of water and titrated to the Ag2CrO4 endpoint, requiring 25.63 mL of 0.1110 M AgNO3. A blank titration requires 1.15 mL of titrant to reach the same end point. Report the %w/w KCl and NaBr in the sample. KCl = 74.551 NaBr = 102.89A 50.00 ml aliquot of a solution containing Ca2+ and Mg2+ was buffered at pH 10 and titrated with 0.0499 M EDTA. The endpoint volume was 40.17 ml. A second aliquot of the same mixture was made strongly basic by the addition of NaOH – this causes the Mg2+ to precipitate as Mg(OH)2. The solution was then titrated with the 0.0499 M EDTA and the endpoint volume was found to be 34.70 ml.A 50.00 ml aliquot of a solution containing Ca2+ and Mg2+ was buffered at pH 10 and titrated with 0.0418 M EDTA. The endpoint volume was 44.36 ml. A second aliquot of the same mixture was made strongly basic by the addition of NaOH – this causes the Mg2+ to precipitate as Mg(OH)2. The solution was then titrated with the 0.0418 M EDTA and the endpoint volume was found to be 30.02 ml. Calculate the molar concentration of Mg.