The third question: a parallel generator that supplies a load of 500 amperes and has a terminal voltage of 240 volts. The product circuit resistance and the field circuit resistance are 0.04 and 60 ohms, respectively. Calculate: a- field current b- product current c- s. Dr. K. induced. 10:38 AM

The third question: a parallel generator that supplies a load of 500 amperes and has a terminal voltage of 240 volts. The product circuit resistance and the field circuit resistance are 0.04 and 60 ohms, respectively. Calculate: a- field current b- product current c- s. Dr. K. induced. 10:38 AM

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.48P

See similar textbooks

Related questions

Q: Q/What is the effect of the length of the transmission line on the Phasor measurement unit (PMU)…

A: - A phasor measurement unit (PMU) is a gadget used to gauge the greatness and stage point of an…

Q: Incremental fuel cost of a generator is given as 3 P12+ 40 P1 +90 $/MWh. Give the cost function and…

A: Incremental fuel cost of a generator is given as 3 P12+ 40 P1 +90 $/MWh. Give the cost function and…

Q: Some test have been made on a 250 kVA, 800 V, 50 Hz three-phase star connected synchronous generator…

A: An alternator/Synchronous generator is a type of electrical machine that converts mechanical energy…

Q: a) By comparing the principle of operation of a "three" phase generation system with a single-phase…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A short-shunt compound generator delivers a load current of 30 A at 220 V, and has armature,…

Q: The following diagram shows a DC generator delivering power to a static load under transient…

A: Apply KVL in outer circuit (stator circuit) -Eg+iaRa+iajXa+Vt=0Vt=Eg-iaRa+jXaVt V/S ia

Q: Q4/ /A/ A 3-phase, Shp, 208V, 4-pole, 60H IMbjected to no load test at 60HZ and short circuit at…

Q: 1. A 30-kVA, 440-V, 50-Hz, 3-0, star-connected synchronous generator gave the following test data :…

A: Voltage regulation: It means the fluctuation in voltage at receiving end. This should be minimum…

Q: 3. Do the excitation current (If) and the generator voltage ( Vg ) increase with the same ratio ?…

A: As per our policy we can provide solution of first question only. Yes, the excitation current &…

Q: 3. Do the excitation current (If) and the generator voltage (Vg) increase with the same ratio ?…

A: This problem is from geneeator.

Q: ) Name the component in the generator which produces unidirectional current. i)Draw the experimental…

A: The shunt generator delivers 160A (IL) at a terminal voltage of 230V (Vt). The shunt field current…

Q: 4. Determine the voltage regulation of a 2,000-V, 1-phase alternator giving a current of 100 A at…

Q: given below, gives the data for the 4/ The total 0.C Characterstics of acle shunt generator at loo0…

A: DC shunt generator Given data of field current and open circuit voltage is for 1000 rpm and we…

Q: (c)Derive EMF Equation of the DC generator

A: Let ∅ = flux per poleZ = total armature conductorA = number of parallel pathP = number of polesN =…

Q: A 60-Hz synchronous generator having inertia constant H9.94 MJMVA and a transient reactance X0.3 per…

Q: The third question: a parallel generator that supplies a load of 500 amperes and has a terminal…

Q: In the system shown below, the generator is ideal (Xs = 0) and the magnitude of the load bus…

Q: A 19 kVA, 419 V, 50-Hz, 3-φ, star-connected synchronous generator gave the following test data :

Q: 1/In the Transmission Line Simulator, the Transmission Line is connected in Nominal-Pi Circuit.…

A: According to the question we have to discuss about transmission line simulator,the Transmission Line…

Q: Q5) discuss the synchronous generator 1- principle operation 2- frequency 3- equivalent circuit

Q: 6. A 3-phase AC generator is supplying power to a load of 3200kW at 2300V and a power factor of 60%.…

Q: 6.5 Consider the three-bus power system shown in Figure P6.5 The table below shows the data about…

Q: A 381 V, 50 Hz, Y-connected, eight poles synchronous generator has the OC given in tabular form…

A: Given data, f=50 HzP=8

Q: Q1.A. The following results give the open circuit characteristic of de shunt generator running at…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: The figure attached to this question shows the 1 line diagram of a simple three bus power system…

A: Convert the line impedances into admittances, using Y=1/Z

Q: A 381 V, 50 Hz, Y-connected, eight poles synchronous generator has the OCC given in tabular form…

A: In this question we need to find a Field current required to keep a terminal voltage 381 V.

Q: In the system shown below, the generator is ideal (Xs = 0) and the magnitude of the load bus…

Q: Determine the voltage regulation of a 2,000-V, 1-phase alternator giving a current of 100 A at 0.8…

A: For a 1-phase alternator,The full load voltage, VFL = 2000VCurrent, I=100APower factor,…

Q: The fuel cost curve of two generator are given under C1 = 00+ 45 P +01 P;? C) = 2000 + 43 P + 0.003…

Q: a) Draw impedance diagram in per unit, by using 100-MVA base. Select 20kV as the base voltage for…

A: You have asked multiple independent questions. We are authorized to answer one question at a time.…

Q: 1. The following data relate to a 6,600-V, 10,000-kVA, 50-Hz, 3-0, turbo- alternator: O.C. kilovolt…

A: Explanation: Given that the power factor = cos ϕ = 0.8 Therefore, tan ϕ = tan (cos-10.8) = 0.75 Sin…

Q: Explain the power flow diagram of a de generator. Q1/

Q: A separately excited dc generator is rated at 172 kW, 430 V, 400 A, and 1800 r/min. Ra = 0.05 N, Rf…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: onstruction, o

A: AC GENERATOR: AC generator is an electric generator that converts mechanical energy to electrical…

Q: Some test have been made on a 250 kVA, 800 V, 50 Hz three-phase star connected synchronous generator…

Q: a) The following information is given for a 34.5 kW, 23 shunt field, series field, diverter and…

Q: Q3:A- Draw the approximate equivalent circuit, power block diagram and phasor diagram of three-phase…

Q: 5.115. A star-connected synchronous machine, with Z, 1+j 102 per phase, is synchronized with an…

Q: State True or false a- The DC load flow study is a linear analysis b- In a load frequency control, a…

A: a ) True In DC power flow analysis no reactive power , inductor, capacitor are present hence it is…

Q: QI The fuel-cost functions in Sh for three thermal plants are given by 5 = 350 + 7.20P, + 0.0040P F-…

Q: A 350 V, 50 Hz, Y-connected, eight poles synchronous generator has the OCC given in tabular form…

Q: 2. A short shunt compound generator has an armature, shunt field and series field resistances of…

Q: The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: Q1.A. The following results give the open circuit characteristic of de shunt generator running at…

A: As per policy, I can submit only 1 answer in post. Kindly submit B question another post The…

Q: Example 8.4 The one line diagram of a simple three-bus power system is shown in the figure. Each…

Q: DC generators operating in parallel

A: Parallel Operation of DC Generator The Parallel Operation of the generator is very necessary if we…

Q: There are only two generators in a power system, and these generators supply a total load of 10 MW.…

A: According to question:

Q: JR (Jalbuena-Rojas) Industrial and Manufacturing Corporation is rated 4,000 kVA at a power factor of…

A: The solution is given below

Q: 7. Upper limit of voltage on transmission line is limited by corona discharge because A. PUD…

A: In this question , we will calculate synchronous frequency...

Concept explainers

Coulomb’s Law

Coulomb's law states that the attraction or repulsion force between two charged things is proportional to the product of their charges and inversely proportional to the square of their distance. It has an effect along the line that connects the two-point charges.

Question

I need the answer as soon as possible

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 6,600V, 1,200 kVA, 3-phase alternator is delivering full load at 0.80 power factor lagging. Its reactance is 25% and resistance is negligible. By changing its excitation, the emf is increased by 30%. At this load, determine the new current and power factor. Draw the single line diagram.
• Zh = 100 ohm • Draw the pu reactance diagram by taking Ut(base) = 132kV, St(base) = 100MVA. If the 33 kV busbar voltage is kept constant at 30 kV and 0.8 inductive 50 MVA power is drawn from this bus, what is the voltage at the synchronous machine ends?
a short three phase transmission line connected to 33kv 50 hertz generating station at starting and is required to supply a load of 10 MW at pointed start lagging power factor at 30 KV addresses in that is the minimum transmission efficiency is to be determined96% estimate the per face value of resistance and inductance of a line
A440V,22.5-hp,50Hz,3-phase,4-pole,star-connectedinductionmotorhasthefollowing impedances in ohms per phase referred to the stator circuit:R1 = 0.55Ω R2 = 0.35ΩX1 = 1.105Ω X2 = 0.456Ω XM = 27.1ΩThe total rotational losses are 1105 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2.3% at the rated voltage and rated frequency, calculate:d) Electrical power, e) Output power,f) Efficiency.
A440V,22.5-hp,50Hz,3-phase,4-pole,star-connectedinductionmotorhasthefollowing impedances in ohms per phase referred to the stator circuit:R1 = 0.55Ω R2 = 0.35ΩX1 = 1.105Ω X2 = 0.456Ω XM = 27.1ΩThe total rotational losses are 1105 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2.3% at the rated voltage and rated frequency, calculate:g) The shaft torque of the motor at rated load
480V, 375 kVA, 0.8 lagging power factor Y - connected synchronous generator has synchronous reactance of 0.4 ohm and negligible armature resistance. This generator is supplying power to 480V 80KW 0.8 P.F leading , Y - connected S.M with synchronous reactance of 1.1 ohm and negligible armature resistance . The S.G is adjusted to have a terminal voltage of 480V when the motor is drawing the rated power at unity power factor . Calculate 1) the magnitudes and angles of emf for both machines. 2) if the flux of motors is increased by 10 percent, what happens to the terminal voltage of power system? What is its new value ? 3) what is the power factor of the motor at the new case.
A 3Ø, Y-connected alternator is rated at 1,600KVA, 13.5KV. The armature effective AC resistance per phase is 1.5Ω. The percentage regulation for a load of 1,280kW at unity power factor is 3.5%. Determine:(a) synchronous reactance of the alternator(b) %VR at full-load 0.8pf leading(c) What is the effect on %VR value if taken at half-load lagging pf? Justify andexplain briefly your answer on one(1) sentence.
Three-phase alternator supplying a three wires, CBA system with a line voltage of 100 Volt, connected to a three impedances of 3 - j 4 in Delta connection. Determine the line current, phase current, phase and line voltage and draw the voltage-current phasor diagram, assuming that VBC is the reference vector.
A 3 phase mesh-connected AC generator has a power angle of 15.4 degrees and synchronous impedance of 0.5 + j10 per phase while delivering 300A to its load at a lagging power factor and 13,200 volts line to line. Find the no load emf in volts, line to line.
A 19 kVA, 419 V, 50-Hz, 3-φ, star-connected synchronous generator gave the following test data : Field current (A): 2 4 6 7 8 10 12 14 Terminal volts: 155 287 395 440 475 530 570 592 S.C. current : 11 22 34 40 46 57 69 80 Resistance between any two terminals is 0.3 Ω Find regulation at full-load 0.8 p.f. lagging by synchronous impedance method. Take ZS corresponding to S.C. current of 80 A.
synchronous generator operating under steady conditions supplying a load current I0to the bus at a terminal voltage of V0. E, is the induced emf under loaded condition and Xa is the direct axis synchronous reactance of the machine. Draw the equivalent circuit model of the system.
Using a test equipment, Vmax was found to be 5V while Vmin is 1V. The distance between voltage maximas is 14 cm and the first maximum was found to be 7 cm from the load. What is the load impedance if the characteristic impedance of the line is 75 ohms?