The transformer is specified to have a 12 V rms secondary voltage for the standard 120 V across the primary. Assuming the practical model and silicon diodes, a) Determine the peak output voltage for the bridge rectifier b) PIV rating is required for the diodes? 120 V ellel ellee Vp(sec) D3 D₂ D₁ R₁ 'D, 10 ΚΩ Vp(out)

The transformer is specified to have a 12 V rms secondary voltage for the standard 120 V across the primary. Assuming the practical model and silicon diodes, a) Determine the peak output voltage for the bridge rectifier b) PIV rating is required for the diodes? 120 V ellel ellee Vp(sec) D3 D₂ D₁ R₁ 'D, 10 ΚΩ Vp(out)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4670V = VsR = 200kΩ C = 0.1μF Consider the circuit and parameters illustrated above. If a derating factor of 12% is sugested then calculate, 12) the maximum reverse voltage rating of the diodes; 13) the string efficiency of this arrangement; 14) the maximum difference in leakage current of the diodes; 15) the maximum difference in stored charge of the diodes.
The secondary input voltage to a single phase diode bridge rectifier is 50V, 50Hz, and the load can be replaced by a resistance of value 20ohms (a) Sketch a well labelled circuit of the converter described above. (b) Sketch the waveforms for the input voltage, output voltage, output current, and output current (c) Derive an equation for average output voltage and calculate for output dc voltage (d) Calculate the ripple factor of the output voltage (e) Transformer utilization factor (h) How can the ripple be improved
A number of diodes rated at 1620 V each are to be connected in series in a rectifier circuit with a maximum voltage of 3000V. A de-rating factor of 15% is recommended. The maximum difference in leakage current of the diodes is given as 10mA , and the maximum difference in stored charge is 20µC. Calculate, 1) the number of diodes that must be used, 2) a suitable component value for the static equalization circuit; 3) a suitable component value for the dynamic equalization circuit.
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
A fully controlled three-phase rectifier bridge circuit supplies a dc load of 300V,60A, from 415V 3-phase ac supply via delta-star transformer. (i) Determine the required thyristor and transformer specifications. (ii) Draw the load and thyristor voltages when firing angle alpha = 60°. (ii) If a commutating diode is placed across the load, determine the FWD specification and then calculate the average load voltage and FWD average current when firing angle alpha = 45°
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
A single-phase full-wave rectifier uses a power transformer whose secondary voltage is 220V r.m.s. The load resistor is 100kΩ. Neglect the transformer losses and the forward drops in the diodes. Determine the following: DC output voltage 2. Ripple voltage
A step-down transformer supplies 25Vrms to a simple half wave rectifier power supply which is connected to a load resistance of 912ohm. The diode breakdown voltage, Vf is 0.7 V. Calculate the amplitude of the peak output voltage, Vpo appearing across the load., calculate the average DC voltage appearing across the load, calculate the DC current in mA drawn by the load.
A three-phase bridge rectifier uses diodes rated at IdRMS = 145, VRRM =1000V and VD=0.7V. The rectifier isfed from a transformer with an inductance of 0,5mH per phase. Assume infinite inductive filtering and calculate, 1. the maximum DC output current;2. the maximum DC output voltage;3. the overlap angle.
A FW rectifier is required to deliver 48VDA with 10% ripple on a 7.5Ω resistor. a)Identify the capacitor providing these values (capacitance and ripple current - ripple current). b)Identify the necessary welding transformer for 120VAA 60Hz welding.c) Find the required serial inductance value for continuous current withdrawal from the source
Which of the following indicates the correct rms value of the diode current for a 1-0 full bridge diode rectifier supplied by a source voltage of 220 V, 60 Hz? The value of load resistance is 2012 (assuming large inductance for maintain constant load current). (a) 9.90 A (b) 7.0 A (C) 4.95 A (d) 11 A COMPANY
When Vs=4290 Consider the circuit and parameters illustrated below.if a derating factor of 12% is suggested then calculate: 12) The maximum reverse voltage rating of the diodes. 13)The string efficiency of the arrangement 14)The maximum difference in leakage current of the diodes and the maximum difference in stored charge of the diodes.