Use the illustration below to answer questions 19 and 20. Downward force 500 N Area 20 m2 Area 1 m2 Upward force = 10,000 N Pressure in tube 500 N/m2 19. Name and explain the principle that is used in lifting the car. 20. Explain what would happen if you dou- bled the area of the piston on the right side of the hydraulic system.

Use the illustration below to answer questions 19 and 20. Downward force 500 N Area 20 m2 Area 1 m2 Upward force = 10,000 N Pressure in tube 500 N/m2 19. Name and explain the principle that is used in lifting the car. 20. Explain what would happen if you dou- bled the area of the piston on the right side of the hydraulic system.

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter7: Statistical Data Treatment And Evaluation

Section: Chapter Questions

Problem 7.24QAP

See similar textbooks

Similar questions

A sample of benzoic acid is contaminated with methyl red, a compound that is soluble in cold water. Which will be necessary to purify it? a) hot gravity filtration b) vacuum filtration c) both Explain your answer.
Explain the difference between constant rate filtration and constant pressure difference filtration using mathematics and examples. When might either of these procedures be used in conjunction with filtration?
Chemistry How to increase storage and shelf life of ready to drink bottled sorghum porridge using stabilizers ( state names of stabilizers to use and the amounts to add) or any other ingredients to use so that sedimentation or settling of dispersed particles is prevented without hindering the taste of the porridge so that the porridge can be sold in the market?
Anion Test - Nitrate (NO3‾) Procedure : Mix H2SO4 4 M into 5 drops of NO3‾ solution (NaNO3 0.5 M) until the solution become acidic (check with litmus paper). Add 5 drops of FeSO4 0.1 M and 2 mL of 4 M H2SO4. When adding in the 4 M H2SO4, make sure the test tube in the position 45°, so that the sulfuric acid can flow through the wall of test tube and form a different layer at the bottom part of the test tube. Results : NO3- solution after adding H2SO4 becomes acidic and is checked by litmus paper and has turned into red colour. Clear solution is obtained at the bottom of the test tube. What is the Chemical equation involved and Discuss the Nitrate test?
Can elastic hose use for pumping and transferring concentrated solution of CH3COOH for long time? If not let explain why and propose at least two types of material which are properly used in this case.
DATA Note: Use the videos as references except when data is provided here. Table 1. Selection of Recrystallizing Solvent. Solvents Dissolution at room temperature? (+ or −) Dissolution at elevated temperature? (+ or −) Distilled water - - Acetone + n/a 95% ethanol - + Toluene + n/a Solid sample: Naphthalene Table 2. Mass Measurements. Mass, g Sample solid 0.5021 Empty watch glass 35.7602 Watch glass with recrystallized sample 36.2485 Table 3. Melting Point Determination. Temperature, oC Appearance of Sample in Capillary Tube … Solid 78.4 Solid 79.3 Solid with signs of liquid 79.9 Solid, liquid 80.6 Liquid, solid 81.3 Liquid with signs of solid … Liquid Theoretical Melting Point, oC: 80.2°C (176.4°F) QUESTIONS Which solvent should be used as the recrystallizing solvent? Check if your chosen solvent satisfies all characteristics of a good…
Show complete solut
A core sample is saturated with an oil (?o = 35oAPI), gas and water. The initial weight of the sample is 224.14 g. After the gas is displaced by water (?w = 1 g/cm3 ), the weight is increased to 225.90 g. The sample is the placed in a Soxhlet distillation apparatus, and 4.4 cm3 water is extracted. After drying the core sample, the weight is now 209.75 g. The sample bulk volume, 95 cm3 is measured in a mercury pycnometer. Find the porosity, water saturation, oil saturation, gas saturation and lithology of the core sample.
The %purity of a powdered crude sample of Na2CO3 containing only inert impurities is to be determined by reacting 225.0 mg of the crude sample to 10.0 mL of 3.00 M HCl solution, and bubbling the resulting CO2(g) product in water that is at exactly 29 °C. After the reaction has completed, the level of the liquid inside the eudiometer rests 4.30 cm above the water level in the beaker. The graduation on the eudiometer indicates that the trapped gas is 44.37 mL. The experiment was done under a barometric pressure of 755.2 torr. a. How many moles of CO2 were collected? b. What is the percent purity of the sample? Round off to the nearest whole number
The %purity of a powdered crude sample of Na2CO3 containing only inert impurities is to be determined by reacting 225.0 mg of the crude sample to 10.0 mL of 3.00 M HCl solution, and bubbling the resulting CO2(g) product in water that is at exactly 29 °C. After the reaction has completed, the level of the liquid inside the eudiometer rests 4.30 cm above the water level in the beaker. The graduation on the eudiometer indicates that the trapped gas is 44.37 mL. The experiment was done under a barometric pressure of 755.2 torr. What CASE does this experiment satisfy?
1. How to collect main batch of crystals using vacuum filtration (Set-up, things to remember)• Why use small amounts of cold water for washing? What is being washed away (2things)?2. Why measure the volume of mother liquor in a graduated cylinder?3. How to let the main batch of crystals dry/how will they be stored until next week?4. How to collect the small amount of crystals from step 4 (those that were not subjected tocrystallization)• What can we expect of this small batch of crystals compared to the main batch?
Please help me set up and solve the bottom problem like #1 is done.