Which of the following questions would be asked in a process analysis of a collegeadmissions office?a. When was the college founded?b. How long does it take the office to process an application?c. How much is the yearly tuition at the college?d. How long does it take the average student to complete a degree program at the college?

Which of the following questions would be asked in a process analysis of a collegeadmissions office?a. When was the college founded?b. How long does it take the office to process an application?c. How much is the yearly tuition at the college?d. How long does it take the average student to complete a degree program at the college?

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter4: Linear Programming Models

Section: Chapter Questions

Problem 111P

See similar textbooks

Similar questions

Explain how having more work-in-process inventory can improve the efficiency of a process. How can this be bad?
Imagine you could take a tour of the Tesla plant. To prepare for this tour, draw a simple process flow diagram of the operation. What is the cycle time of the process (assume two shifts of 8 hours each and 5 days a week of operation)? What is the flow time? Where in the process do you expect to encounter inventory? How many cars are you likely to encounter as work in progress inventory?
Of the following process types, ________ has the lowest output variety, and the highest output volume. A) Assembly line B) Batch C) Job shop D) Project
Choice Bank receives credit card applications that need to be reviewed for a decision. There are two types of applications; preapproved, and non-preapproved. Preapproved applications only need a quick review and therefore take 6 minutes to process. Applications that are not preapproved need a secondary credit check and take 15 minutes to process. 8. The bank receives 10 preapproved applications every hour and 6 applications that are not preapproved every hour. What is the utilization of the process?
Give only typing answer with explanation and conclusion Your process runs for 18 hours a day and 220 days a year. Your bottleneck is 5 minutes. You make $35 an item. What is the monthly and annual income?
Peter’s Paper Clips uses a three-stage production process: cutting wire to prescribed lengths, inner bending, and outer bending. The cutting process can produce at a rate of 220 pieces per minute; inner bending, 230 pieces per minute; and outer bending, 180 pieces per minute. Determine the hourly capacity of each process stage and the number of machines needed to meet an output rate of 14,000 units per hour. Round your answers for the hourly capacity of each process stage to the nearest whole mumber. Round your answers up for the number of machines needed to a whole number. Cutting process: Hourly capacity: pieces/hour Number of machines needed: machine(s) Inner bending: Hourly capacity: pieces/hour Number of machines needed: machine(s) Outer bending: Hourly capacity: pieces/hour Number of machines needed: machine(s)
Please answer fast ASAP an automobile spare parts production required 5 types of process to complete final product. the process are cutting turning shaping drilling and knurling.the operation time required in each processes is 3,2,4,1,5 minutes. Calculate the machine required in each step to get 60 pieces of final product in an hour.
Melissa's Photo Studio offers both individual and group portrait options. The process flow diagram below shows that all customers must first register and then pay at one of two cashiers. Then depending on if they want a single or group portrait they go to different rooms. Finally everyone picks up their own finished portrait. RegistrationCahier ACahier B(4 min)(4 min)(6 min) x y graph Pick up portraitIndividualGroup(5 min)(12 min)(15 min)portrait takenportrait taken x y graph a. How long, on average, does it take to complete the entire process for a group portrait? nothing minutes. (Enter your response as an integer.)
Bill’s Barbershop has two barbers available to cut customers’ hair. Both barbers provide roughly the same experience and skill, but one is just a little bit slower than the other. The process flow in Figure shows that all customers go through steps B1 and B2 and then can be served at either of the two barbers at step B3. The process ends for all customers at step B4. The numbers in parentheses indicate the minutes it takes that activity to process a customer.a. How long does it take the average customer to complete this process?b. What single activity is the bottleneck for the entire process?c. How many customers can this process serve in an hour?
The M–N plant manufactures two different products: M and N. Selling prices and weekly market demands are shown in the following diagram. Each product uses raw materials with costs as shown. The plant has three different machines: A, B, and C. Each performs different tasks and can work on only one unit of material at a time. Process times for each task are shown in the diagram. Each machine is available 2,500 minutes per week. There are no "Murphys" (major opportunities for the system to foul up). Setup and transfer times are zero. Demand is constant. Operating expenses (including labor) total a constant $12,000 per week. Raw materials are not included in weekly operating expenses. a. Which machine is the constraint in this plant? multiple choice Machine A Machine C Machine B Incorrect
Give 5 answers to each question. a. In a call that falls under the category of "customer care call," what should an agent always keep in mind or do? b. In a call that falls under the category of "collection call," what should an agent always keep in mind or do?
The following flow chart shows the entire manufacturing process at KD Manufacturing, which consists of six independent operations processes (i.e. sawing, sanding, drilling, reshaping, welding, and assembly). The entire process flow starts with the input of three different parts, Part I, Part II and Part III, each entering a different input line. Three parts meet later for the welding, whichever welding station is available (two identical welding stations work independently). After welding is completed, the product is sent to one of the three assembly stations (which are in parallel). The chart also shows the processing time per unit (in minutes) for each operation. Each of sawing, sanding, drilling and reshaping stations is handled by a different worker. Two workers handle welding, each at one welding station. Another three workers handle the assembly process independently, one at each assembly station. To improve the capacity of the entire manufacturing process, the manager decides to…