Your second customer wants to determine the required electrical power, which will be used to pump waterwith the following design specifications: The pump loses 3 kW in the form of heat to its surrounding. The inlet and the exit conditions of the water are as indicated in Figure 2. The pipe diameter is 5 cm. P2 = 150 kPa V2= 1 m/s Zz= 105 m Q - 3 kW Motor Welectrical | Water P:= 100 kPa O Vi= 1 m/s Zı= 5 m Figure 2: Schematic for task 2. You must follow the following parts to do your task: Part 1 Derive the steady flow energy equation (SFEE) from the first principles. You are required to show all the steps in deriving the SFEE and using both the principles of mass and energy conversation. Part 2 Produce specific steady state energy equation (SFEE) by stating all the stated assumption in this equipment in order to be used in later stages without further analysis. Then calculate the pump power.

Your second customer wants to determine the required electrical power, which will be used to pump waterwith the following design specifications: The pump loses 3 kW in the form of heat to its surrounding. The inlet and the exit conditions of the water are as indicated in Figure 2. The pipe diameter is 5 cm. P2 = 150 kPa V2= 1 m/s Zz= 105 m Q - 3 kW Motor Welectrical | Water P:= 100 kPa O Vi= 1 m/s Zı= 5 m Figure 2: Schematic for task 2. You must follow the following parts to do your task: Part 1 Derive the steady flow energy equation (SFEE) from the first principles. You are required to show all the steps in deriving the SFEE and using both the principles of mass and energy conversation. Part 2 Produce specific steady state energy equation (SFEE) by stating all the stated assumption in this equipment in order to be used in later stages without further analysis. Then calculate the pump power.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.33P

See similar textbooks

Similar questions

Water from a reservoir is pumped over a hill through a pipe 450 mm in diameter and a pressure of 1 kg/cm2 is maintained at the summit. Water discharge is 30 m above the reservoir. The quantity pumped is 0.5 m3/sec. Frictional losses in the discharge and suction pipe and pump is equivalent to 1.5 m head loss. The speed of the pump is 800 rpm what amount of energy must be furnished by the pump, kW?
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
This is a fluid machine question. Water reservoir is pumped over a hill through a pipe 450 mm in diameter and a pressure of 98.08 kPa is maintained in the summit water discharge is 30 m above the reservoir. The quantity pumped is 0.50 m3/s. rrictional losses in the discharge and suction pipe of the pump is equivalent to 1.5 m head loss. The speed of the pump is 800 rpm, what amount of energy must be furnished by the pump in kW?
include a free body diagram Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere and the water enters the tank from a 80 m height. The overall efficiency of the motor pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 KW. If the irreversible headloss in the piping is 7 m, the velocity of the water (in m/s) at the tank inlet isA. 6.21B. 7.12C. 8.7D. 5.05
Calculate the power required to pump water at 120 kg/s from a supply tank, through an 18 cm diameter galvanised iron pipe to a storage tank located 12m above the supply tank. The length of the pipe is 70 m. All losses other than friction losses are ignored. [Hint: Use Moody Diagram] (For water, ρ = 1000 kg/m3, μ = 1.003 x 10-3 Pa.s)
1) Which of the following statement is NOT correct about piping network? a) In parallel pipes, the flow rate is proportional to its diameter and inversely proportional to its length and friction factor. b) When analyzing the piping network, conservation of mass throughout the system must be satisfied. c) In piping systems with pumps, the Bernoulli equation should be corrected by introducing a kinetic energy correction factor. d) The algebraic sum of head losses for all loops equal to zero. 2) The EGL is always a distance V2/2g above the HGL. True or False
In a cast-iron piping system of 450 ft length shown below, the rate of flow is 1 cfs at 70°F. Assuming the total head losses for the flow in the system is 10 ft, what is the energy head supplied by the pump E? a. 40 ft b. 50 ft c. 60 ft d. 510 ft e. None of the above
Water from a reservoir is pumped over a hill through a pipe 900 mm in diameter and a pressure of one kg/cm? is maintained at the pipe discharge where the pipe is 85 m from the pump centerline. The pump have a positive suction head of 5 m. Pumping rate of the pump at 1000 pm is 1.5 m/sec. Friction losses is equivalent to 3 m of head loss. What amount of energy must be furnished by the pump in KW?
A 28-in pump is used to deliver water from a lower reservoir to a higher reservoir . The total length of the 10-in-ID pipes is 62 ft. and the friction factor is taken as 0.022. If the pump head H can be defined as a function of discharge Q in ft3/s is: H = 365 - (0.04718Q^2), in feet. What is the operating discharge rate in ft3/s?
fan ventilates at 500rev/min, the airflow is measyured at 150cubic meters/second. the ventilation pressure is 0.40kPa while thepressure along fan is0.85kPa.the mine requires 100cubic meters/second of air flow on an off day.efficiency=0.75. 1.new slow down speed required on an off day 2. Annual savings in electricty if the costs is R0.63/kWh 3. Comment on any savings in the maximum demand. 4. methods for reduction of speed on off-day.
The old Hydraulics laboratory in Mechanical Engineering used a roof tank tosupply apparatus with water at a nearly constant head. The water wascollected in an under floor sump, and then pumped back to the roof tankafter the experiment. The flow rate was 10 litre s-1. The tank was 6m abovethe sump, and the length of the pipe route was 15 m. The old 6” pipes arenow heavily corroded (k = 7.5 mm). The old pump has been scrapped. Whathead ΔH would be specified for a pump to restore the system using the oldpipes? What would the pump power be? If the pipes were replaced with 150mm diameter PVC pipes, what pump ΔH would be required?
A water pump is used to pump water from one large reservoir to another large reservoir that is at a higher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure, as sketched in Fig. The dimensions and minor loss coefficients are provided in the figure. The pump’s performance is approximated by the expression Havailable = H0 − aV.2 , where shutoff head H0 = 24.4 m of water column, coefficient a = 0.0678 m/(Lpm)2 , available pump head Havailable is in units of meters of water column, and capacity V. is in units of liters per minute (Lpm). Estimate the capacity delivered by the pump. A