Sustainable Energy, SI Edition
2nd Edition
ISBN: 9781337672092
Author: DUNLAP, Richard A.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 1, Problem 19P
To determine
Find the power plant’s rate of coal consumption.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
An average American consumes approximately 105 kJ of energy per day. The average life expectancy of an American is 77.9 years.
How much coal would need to be burned to provide enough energy to meet a person's energy demands if the efficiency of energy production from coal is 38%?
☐g coal
A 60 MW steam power station has a thermal efficiency of 30%. If the coal burnt has a calorific value of6950 kcal/kg, calculate :(i) the coal consumption per kWh,(ii)the coal consumption per day.
If the energy present in a jet of water of 20 cm diameter and having a velocity of 25 m/s could be extracted by a device with 90% efficiency, the power extracted would be nearly.
sec²
m
tak ing
1
2g
0.051
Chapter 1 Solutions
Sustainable Energy, SI Edition
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A diesel engine required 9,800 kJ of heat to produce 1,800 kJ of power. What is its efficiency?arrow_forwardAn engine absorbs 100 J and rejects 60 J in each cycle. (a) What is its efficiency? (b) If each cycle takes 0.5 s, find the power output of this engine in watts.arrow_forwardConsider a 400-MW, 32 percent efficient coal-fired power plant that uses cooling water withdrawn from a nearby river (with an upstream flow of 10-m3/s and temperature 20 °C) to take care of waste heat. The heat content of the coal is 8,000 Btu/lb, the carbon content is 60% by mass, and the sulfur content is 2% by mass. How much electricity (in kWh/yr) would the plant produce each year? How many pounds per hour of coal would need to be burned at the plant? Estimate the annual carbon emissions from the plant (in metric tons C/year). If the cooling water is only allowed to rise in temperature by 10 °C, what flow rate (in m3/s) from the stream would be required? What would be the river temperature if all the waste heat was transferred to the river water assuming no heat losses during transfer? Estimate the hourly SO2 emissions (in kg/h) from the plant assuming that all the sulfur is oxidized to SO2 during combustion.arrow_forward
- A 1000 MW coal fired power plant (30% efficiency). The coal is 75% carbon and has a heat content of 10, 000 BTU/lb. What is the carbon emission (ton carbon per year)?A 1000 MW natural gas plant (45% efficiency). The gas is CH4 with a heat content 800 BTU/mol. What is the carbon emission (ton carbon per year)?Calculate carbon emission reduction if the above natural gas plant is used to replace the coal fired plant.(Here ton is metric ton, 1 ton=2,200 lb)arrow_forwardWrite down the chemical formulae for the combustion of the alkanes in Table 3.2 with n = 2 to n = 8. Determine the mass of CO2 produced per megajoule of energy.arrow_forwardA piston cylinder device contains 5 kg hydrogen gas. Heat is transferred to the hydrogen as the temperature increases by 23.28 F. What is the boundary work done during this process kW.arrow_forward
- The change in internal energy for the combustion of 1.0 mol of octane at a pressure of 1.0 atm is -5084.3 kJ . If the change in enthalpy is -5074.0 kJ , how much work is done during the combustion? Express the work in kilojoules to three significant figures.arrow_forwardCellulose is to be burned in a waste to energy facility. The chemical equation for cellulose is C6H10O5. The atomic weights of C, H, and O are 12, 1, and 16, respectively. The ideal equation for the combustion of cellulose is C6H10O5 +6O2à6CO2 + 5H2O. Calculate the stoichiometric oxygen necessary for the combustion of cellulose. Calculate the stoichiometric air supply. The air is 23.15% oxygen by weight. If the facility operates at 1.5 tons/hour at 100% excess air. How much air is required?arrow_forwardThe Bunsen burner in your labs are fueled by natural gas, which is mostly methane, CH4. The thermochemical equations for the combustion of methane (burning in oxygen) is: CH4(g) + 2 O2(g) ➔ CO2(g) + 2 H2O (g) ΔH = – 890.3 kJ/mole Calculate ΔH in kJ when 5.00 g CH4 react with an excess oxygen.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you