MindTap Engineering for Dunlap's Sustainable Energy, SI Edition, 2nd Edition [Instant Access], 1 term (6 months)
2nd Edition
ISBN: 9781337551755
Author: DUNLAP
Publisher: Cengage Learning US
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 1, Problem 8P
To determine
Find the steam turbine’s ideal Carnot efficiency.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Calculate the pressure on 1.00 lb mol of Nitrogen gas ,N2, contained in a 100 ft^3 container at 70 degree Fahrenheit
Water flows from the ground floor to the third floor in a 4-storey building through a pipe 50 mm in diameter at a rate of 2 L/s and according to the diagram below. The water flows out from the system through a tap with an opening diameter of 15 mm.
Q. Calculate the energy loss due to friction as the water flows through the pipe
1) Heating the water in a 55-gallon water heater requires about 2.0 x 103 kJ of energy.
a) Assume the energy came from natural gas with 80% efficiency; how many grams of natural gas are required?
b) Assume the energy came from electricity with 80% efficiency and that the electricity was produced from the combustion of coal with 30% efficiency; how many grams of coal are required?
For problem above, calculate how much CO2 in grams is emitted to the atmosphere.
For a: Use the balanced equation for the combustion of methane (CH4) to determine how many grams of CO2are produced from the amount of natural gas required.
For b: Assume that coal produces 5.25 kJ of energy per gram of CO2 produced. Calculate how much CO2 in grams is produced.
Chapter 1 Solutions
MindTap Engineering for Dunlap's Sustainable Energy, SI Edition, 2nd Edition [Instant Access], 1 term (6 months)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- 1. Water at 68 has a dynamic viscosity of 1 centipoise. Compute its dynamic viscosity and kinematic viscosity in foot pound-second units. 2. A volume of 15.5 cu.ft of a liquid weighs 782 lb. Compute the mass density of the liquid. 3. Compute the number of watts which are equivalent to 1 horsepower. (1 watt = 10^7 cm-dynes per sec; 1 hp = 550 ft-lb per sec.) 4. A city of 6000 population has an average water use of 110 gallons per person per day. Compute the average total rate of use in cubic feet per second and in gallons per minute. ( 1 cu. Ft = 7.48 gal.) 5. Compute the unit weight and kinematic viscosity, in foot-pound-second units, of dry air at 15 and an absolute pressure of 14.7 lb per sq.in.arrow_forwardThe temperature of 1 m3 of water is decreased by 10C. If this thermal energy is used to lift the water vertically against gravity, what is the change in height of the center of mass?arrow_forwardWater leaving the nozzle at a velocity of 4350 m/min with a volume flow rate of 0.736 m³ . if the density of water is 0.000997 kg/cm³ . How will you determine the potential for power generation in a hydraulic turbine .arrow_forward
- We have exposed 1 kg of water, 1 kg of brick, and 1 kg of concrete each to a heat source that puts out 100 J every second. Assuming that all of the supplied energy goes to each material and they were all initially at the same temperature, which one of these materials will have a greater temperature rise after 10 s? We can answer this question using Equation as shown . We will first look up the values of the specific heat for water, brick, and concrete, which are cwater = 4180 J⁄kg K, cbrick = 960 J⁄kg K and cconcrete = 880 J⁄kg K . Now applying as shown , Ethermal = mc(Tfinal Tinitial) to each situation, it should be clear that although each material has the same amount of mass and is exposed to the same amount of thermal energy, the concrete will experience a higher temperature rise because it has the lowest heat capacity value among the three given materials.arrow_forwardWater flows from the ground floor to the third floor in a 4-storey building through a pipe 50 mm in diameter at a rate of 2 L/s and according to the diagram below. The water flows out from the system through a tap with an opening diameter of 15 mm. Q1. Calculate the energy loss due to friction as the water flows through the pipe (J/Kg) Q2. Calculate the total energy loss due to friction through the system (J/Kg) Q3. Calcualte the pressure at point 1 (kN/m2)arrow_forwardWater flows from the ground floor to the third floor in a 4-storey building through a pipe 50 mm in diameter at a rate of 2 L/s and according to the diagram below. The water flows out from the system through a tap with an opening diameter of 15 mm. Q. Calculate the total energy loss due to friction through the systemarrow_forward
- 3.5 kg of an ideal gas is heated at constant temperature from 15 m3 and 4.0 atm to 35 m3 at Determine the work donearrow_forwardThe design fluid (typically water and antifreeze) flow rate through a solar hot-water heater system is (1 L/s) m ⁄m2 . If a system runs continuously for 3 hours and makes use of two solar panels (each 2 m×4 m) , what is the total volume of the fluid that goes through the collector during this period? Express your answer in liters and m3 .arrow_forwardA volume tank 9m in a diameter and 1.20 m high fill water 20°C in 14 minutes and 6sec. what is the volume flux? And the mass flux (in kilograms per second).arrow_forward
- The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown. The tank is located on a mountain at an altitude of 1400m where the atmospheric pressure is 89.6 kPa. Determine the pressure of air in the tank if h1 = 0.5m, h2 = 0.5m, and h3 = 0.6m. Take the densities of water, oil and mercury to be 1000kg/.850 kg/and 13,600 kg/arrow_forwardThe figure below shows a pump delivering 0.014 m3/s of crude oil (SG = 0.85) from an underground storage drum to the first stage of a processing system. (a) If the total energy loss in the system is , calculate the power added by the pump in kW. (b) If the power input to the pump is 16.5 kW, what is the mechanical efficiency of the pump?arrow_forwardA balloon filled with hydrogen gas has a volume of 5200 cubic centimeters at 44 degrees Celsius and 9.0 x 104 Pa. What volume (in liters) does the H2 occupy at standard temperature and pressure(STP).arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage Learning
Engineering Fundamentals: An Introduction to Engi...
Civil Engineering
ISBN:9781305084766
Author:Saeed Moaveni
Publisher:Cengage Learning