Concept explainers
Another term for an enlargement is a diffuser. A diffuser is used to convert kinetic energy
Want to see the full answer?
Check out a sample textbook solutionChapter 10 Solutions
Applied Fluid Mechanics (7th Edition)
Additional Engineering Textbook Solutions
Engineering Mechanics: Dynamics (14th Edition)
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Mechanics of Materials (10th Edition)
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
- An aircraft is climbing at a constant rate of 1 m/s. On t = 0 s, the altimeter reads 5000m and Altp = 5500m. Find the altitude and pressure at t = 100 s.arrow_forwardSimulation of laminar gas flow in the pipe with Ansys Fluent Task: 1. Calculate velocity distribution in y axis at inlet and outlet of the pipe. Submit it as a chart. 2. Calculate velocity distribution over the pipe length. Submit it as a chart. Figure. pipe geometry L, m = 16 R, m= 0.15 Inlet velocity, m/s= 0.08 Gas= Oxygen Need proper solution like pdf file, don't need steps by steps. If you can can do it through ansys fluent. Write proper solution on word file or pdf.arrow_forwardA pipe network consists of pipeline as shown. If the total rate of flow is 10 liters/sec, compute the following: Rate of flow of pipeline 3, in liters/sec. Rate of flow of pipeline 2, in liters/sec. Total head loss from A to D, in mm.arrow_forward
- A smooth square cylinder is put in 15 °C flowing water. The flow direction is perpendicular to the long axis of the cylinder (parallel to the square section). The edge length of the square is s=2.0m. The long axis length is L=5.0m. The flow velocity is v=0.046 m/s. The density of water is ρ=1000kg/m3. T he dynamic viscosity is η=1.15×10-3kg/m·s. (3) Calculate the drag force FD_________N (2 decimal places)arrow_forwardFluids mechanics suject In the figure shown, compute the pressure difference between m and n when1. Fluid A is brine (rd = 1.15), the gage fluid is oil (rd = 0.92) and z = 1 m.arrow_forwardA 2-1/2 inch fire hose discharges water through a nozzle having a jet diameter of 1 inch. Thelost head in the nozzle is 5.76 percent of the velocity head in the jet. If the gage pressure atbase of nozzle is (a) 86 lb per sq in.: (b) 167 lb per sq in.: (1.1) compute the discharge ingallons per minute: (1.2) what is the maximum horizontal range to which the stream can bethrown, neglecting air resistance?arrow_forward
- The diameter of a pipe at the larger end is 0.6 cm and at the smaller side is 0.3 cm the larger and smaller ends are located 8 meters and 4 meters, respectively, from a datum line. If at the larger end the velocity is 1.2 meters pee second and the pressure is 5300 kN/m^2, compute the pressure at the smaller endarrow_forwardIf the velocity of flow in a 75-mm diameter fire hose is 0.5 m/s, what is the velocity in a diameter 25 mm of a jet issuing from a nozzle attached at the end of the pipe. Compute also the power available in the jet.arrow_forwardWater flows through a 125 mm diameter pipe at a velocity of 7.5 m/sec. Find the mass flow rate in kg/sec. NOTE: Do not write any unit to your answer, put your answer in a numerical form only and use up to 3 decimal places. ASAP PLSarrow_forward
- A needle with a piston is used to extract blood from the arm of a patient. Solve for the ave. speed of the blood flow, in mm/s, in the needle if the radius of the piston is 2.5mm and the diameter of the needle is 0.5mm and length of 10mm. Take into account the blood withdrawing speed of 6mm/s and air leaks around the piston at 20mm3/s.arrow_forwardA wind tunnel has an incompressible flow of air, flowing horizontally from an inlet section, 7 times the test section. A u-tube is connected, containing mercury inside. The mercury has 1.33x10^5 N/m^3 specific weight. The condition of the air at the inlet section is at 1 atm and 280K respectively. What is the change of height inside the mercury, when the velocity at the throat is 70m/s?Complete solutionround off to 4 decimal placesarrow_forwardProblem 1. A fluid is flowing in a 20 cm diameter pipeline with a velocity of 5.50 m/sec. The pressure at the center of the pipe is 35 kPa, and the elevation of the pipe above an assume datum is 5 m. Compute the total energy flowing fluid if it is (a.) water, (b.) molasses (s = 1.20) and (c.) gas (w = 4.29 N/). ANSWERS MUST BE IN 3 DECIMAL PLACES ALL THE WAY.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY