FUND OF AERODYNAMICS(LLF) +CONNECT (1YR)
6th Edition
ISBN: 9781265141387
Author: Anderson
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 10, Problem 10.13P
Consider a rocket engine burning hydrogen and oxygen. The total mass flow of the propellant plus oxidizer into the combustion chamber is 287.2 kg/s. The combustion chamber temperature is 3600 K. Assume that the combustion chamber is a low-velocity reservoir for the rocket engine. If the area of the rocket nozzle throat is
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Consider a rocket engine burning hydrogen and oxygen. The total massflow of the propellant plus oxidizer into the combustion chamber is287.2 kg/s. The combustion chamber temperature is 3600 K. Assumethat the combustion chamber is a low-velocity reservoir for the rocketengine. If the area of the rocket nozzle throat is 0.2 m2, calculate thecombustion chamber (reservoir) pressure. Assume that the gas that flowsthrough the engine has a ratio of specific heats, γ = 1.2, and a molecularweight of 16.
If the calculated mass flow rate of petrol fuel is 9.25 x 10-5 kg/s, what is the time taken for the 10 mL of petrol fuel been supplied into the engine?
Note that the calorific value and density of the petrol fuel are 43 MJ/kg and 712 kg/m3 respectively.
Find the boiler chimney diameter if
the boiler has a capacity of 320 kW
with a combustion efficiency of 75%,
and uses diesel as fuel with a
calorific value of 40000 kJ/kg.
Assume the flue gases density as
1.12 kg/m3 and moving with a
velocity of 4 m/s.
Chapter 10 Solutions
FUND OF AERODYNAMICS(LLF) +CONNECT (1YR)
Ch. 10 - The reservoir pressure and temperature for a...Ch. 10 - A flow is isentropically expanded to supersonic...Ch. 10 - A Pitot tube inserted at the exit of a supersonic...Ch. 10 - For the nozzle flow given in Problem 10.1, the...Ch. 10 - A closed-form expression for the mass flow through...Ch. 10 - Prob. 10.6PCh. 10 - A convergent-divergent nozzle with an...Ch. 10 - For the flow in Problem 10.7, calculate the mass...Ch. 10 - Consider a convergent-divergent nozzle with an...Ch. 10 - A 20 half-angle wedge is mounted at 0 angle of...
Ch. 10 - The nozzle of a supersonic wind tunnel has an...Ch. 10 - We wish to design a supersonic wind tunnel that...Ch. 10 - Consider a rocket engine burning hydrogen and...Ch. 10 - For supersonic and hypersonic wind tunnels, a...Ch. 10 - Return to Problem 9.18. where the average Mach...Ch. 10 - Return to Problem 9.19, where the average Mach...Ch. 10 - A horizontal flow initially at Mach I flows over a...Ch. 10 - Consider a centered expansion wave where M1=1.0...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
The spring of k and unstretched length 1.5R is attached to the disk at a radial distance of 0.75R from the cent...
Engineering Mechanics: Statics
What types of polymers are most commonly blow molded?
Degarmo's Materials And Processes In Manufacturing
6–1C A mechanic claims to have developed a car engine that runs on water instead of gasoline. What is your resp...
Thermodynamics: An Engineering Approach
What is the importance of modeling in engineering? How are the mathematical models for engineering processes pr...
HEAT+MASS TRANSFER:FUND.+APPL.
Steady state conduction rate to the warm compressor to the net power produces theoretically by thermodynamic ba...
Introduction to Heat Transfer
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Obtain an expression for the volume flow rate at the exit of the mixing chamber in terms of the volume flow rates of the two inlet streams and the rate of heat transfer to the mixing chamber.arrow_forwardGas enters the rotor of an axial turbine stage at a speed of 520 m/s with a flow angle of 65°. The blade speed is 300 m/s. The reaction is 0.46 and the utilization is 0.82. Do not assume that the axial velocity is constant and (a) Find the magnitude of the output velocity. (b) Find the work done by the stage. (c) Find the angle at which the relative velocity leaves the stage.arrow_forward2. A cooling tower is used to cool a jacket water loss from the engine. The heat generated by fuel is 2500 kw & cooling loss is 30%, If temperature range of the tower is 15°c. Deter- mine the mass flow of water entering thearrow_forward
- 100% High pressure water and compressed air are delivered to some operating rooms. Bored one day, with no patients around, you take the cap off the nozzle to see what would happen. Water flows through the vertical pipe and nozzle and then exhausts into the air as shown in the diagram. The water pressure in the pipe at position 1 is 3 atm. The pressure when the water discharges to the air is 1 atm. Position 2 identifies the nozzle, 0.75 m above position 1, where the water flow has been constricted from an 8-cm diameter pipe to a 3-cm diameter nozzle. Assume that the free jet remains a stream of water with a 3-cm diameter. Assume no friction losses. Free jet -3 cm diameter 0.75 m a) Determine the mass flow rate of water through pipe at position 1 in kg/s. 3 atm 8 cm diameter b) Determine the height, h, the water jet can rise. c) Calculate the friction factor inside the 8-cm pipe and determine if the assumptions of negligible friction losses was reasonable. Water AR d 128 PM 10/3/2021…arrow_forwardautomobile is traveling at 55 mph on a highway. The car's engine is operating at 2000 revolutions minute. The engine fills its cylinders with air each time two per revolutions are completed, i.e., it operates on a four-stroke cycle. The volume of air ingested during each cycle is 95% of the engine's displacement of 1.5 liters. The air enters the cylinders at 0.7 atm and 305 K. Determine the following: The volumetric flow rate of the air at the entering conditions. Calculate in units of m'/s and ft'/min (CFM). А. 3 The mass flow rate of the air (kg/s). B. bas The volumetric flow rate of the air at standard temperature and pressure С. 3 (STP = 101.325 kPa and 298.15 K). Calculate in units of m'/s and ft'/ min (SCFM).arrow_forwardCalculate the thrust of a turbojet engine with an inlet diameter of 4 ft. If an airplane is flying at altitude of 15km at Mach 0.8 with an exit velocity of 900ft/s. The turbojet engine thrust at 15-km. (in Lbf)arrow_forward
- A steady stream of n-butanol is needed to be fed into the reactor at 40 ̊C. However, the inlet of the reactor is located 7.5 m above the reservoir tank. As such, a highly effective centrifugal pump (70% efficiency) is used for such a purpose. It was understood that the needed volumetric flow rate into the reactor is fixed at 20 m3/h. It was also noted that the n-butanol reservoir is closed but not pressurized, while the gauge pressure at the endof the discharge line is measured at 275 kPa. Given that the density of n-butanol is 810kg/m3. If the discharge pipeline was 5 cm in diameter, calculate: (i) The velocity of n-butanol at the discharge line. (ii) The total power input from the centrifugal pump. (iii) The power delivered to the n-butanol fluid.arrow_forward4. The diameter of the pipes (1) and (2) connected to the tank shown in the figure are 3 cm and the diameter of the pipe (3) is 6 cm. Alcohol with a density of 0.79 is injected into the tank from pipe (1) with a speed of 10 m/s and water is injected to tank from pipe (2) with a speed of 16 m/s. Assuming that there is an ideal mixture in the tank, find the exit velocity of the mixture in the pipe (3) and the specific mass of the mixture. Alcohol (1) (3) Admixture Ideal Mixture Water (2)arrow_forward4. Carbon dioxide flows steadily through a varying cross-sectional-area duct such as a nozzle at a mass flow rate of 3 kg/s. The carbon dioxide enters the duct at a pressure of 1400 kPa and 200°C with a low velocity, and it expands in the nozzle to a pressure of 200 kPa. The duct is designed so that the flow can be approximated as isentropic. Determine the following parameters at each location along the duct that corresponds to a pressure drop of 200 kPa: (i) density; (ii) velocity; (iii) flow area; (iv) mach number. You may assume: • Carbon dioxide is an ideal gas with constant specific heats at room temperature; • Flow through the duct is steady, one-dimensional and isentropic. Use cp=…arrow_forward
- STELIA Aerospace are planning to design a spherical cryogenic tank to be stored with liquid hydrogen. It is also designed with a system that if the tank reaches maximum capacity all entry and exit nozzles will automatically be closed. The specific gravity of this fluid is approximately seven hundredths the density of water. The tank is designed to have two-entry filtration system and an exit nozzle located at the bottom. The liquid hydrogen flows into the cryogenic tank at a rate of 0.85 kilograms per second and 0.75 kilograms per second. At the same time the exit nozzle is opened with a rate of 0.005 kilograms per second. (a)The shutoff valves were closed after 35 minutes, what is the volume and radius of the spherical tank? (b) Using your answers on item a, how full is the tank (in percentage) after 27.15 minutes?arrow_forwardA jet-propelled airliner flies at an altitude of 15,000 m and a velocity of 265 m/s. What is the stagnation pressure and stagnation temperature of the air entering the engine? If the airliner is stationary on the ground, the engines are running with the same Mach number flow into the engines, and the air flow to each engine is 35 kg/s, what is the airflow to each engine at the above flight conditions? Po = Pa To = i mf = K kg/sarrow_forwardProblem 3 – Sparky needs helium for an experimental project. The helium is stored in a storage tank at 20°C and 300 kPa. The helium exits through a converging nozzle to the environment (100 kPa atmospheric pressure) and has 10 mm exit diameter. Determine the exit flow rate of the helium. Helium’s ratio of specific heats is 1.667. This is a compressible flow problem. Only use equations and tables from the textbook to solve this problem. Note the figures in the textbook and textbook appendices are based in air, not helium, and are not valid for this problem.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Extent of Reaction; Author: LearnChemE;https://www.youtube.com/watch?v=__stMf3OLP4;License: Standard Youtube License