EBK PHYSICS FOR SCIENTISTS AND ENGINEER
EBK PHYSICS FOR SCIENTISTS AND ENGINEER
9th Edition
ISBN: 9780100581555
Author: Jewett
Publisher: YUZU
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Book Icon
Chapter 10, Problem 10.64P

A tennis ball is a hollow sphere with a thin wall. It is set rolling without slipping at 4.03 m/s on a horizontal section of a track as shown in Figure P10.33. It rolls around the inside of a vertical circular loop of radius r = 45.0 cm. As the ball nears the bottom of the loop, the shape of the track deviates from a perfect circle so that the ball leaves the track at a point h = 20.0 cm below the horizontal section. (a) Find the ball’s speed at the top of the loop. (b) Demonstrate that the ball will not fall from the track at the top of the loop. (c) Find the ball’s speed as it leaves the track at the bottom. (d) What If? Suppose that static friction between ball and track were negligible so that the ball slid instead of rolling. Describe the speed of the ball at the top of the loop in this situation. (e) Explain your answer to part (d).

Figure P10.33

Chapter 10, Problem 10.64P, A tennis ball is a hollow sphere with a thin wall. It is set rolling without slipping at 4.03 m/s on

(a)

Expert Solution
Check Mark
To determine

The speed of the ball at the top of the loop.

Answer to Problem 10.64P

The speed of the ball at the top of the loop is 2.38m/s.

Explanation of Solution

The radius of the circular loop is 45.0cm, the height of the track from the horizontal section is 20.0cm and the initial velocity of the ball is 4.03m/s.

Write the expression for the law of energy conservation between horizontal track and the top of the loop

    Kt1+Kr1=Kt2+Kr2+U2        (1)

Here, Kt1 is the translational kinetic energy of the ball at horizontal track, Kr1 is the rotational kinetic energy of the ball at horizontal track, Kt2 is the translational kinetic energy of the ball at top point of the loop, Kr2 is the rotational kinetic energy of the ball at top point of the loop and U2 is the potential energy of the ball at top point of the loop.

Write the expression for the translational kinetic energy of the ball at horizontal track

    Kt1=12mv12

Here, m is the mass of the ball and v1 is the initial linear velocity of the ball.

Write the expression for the rotational kinetic energy of the ball at horizontal track

    Kr1=12Iω12        (2)

Here,  I is the moment of inertia of the ball about the center of mass and ω1 is the initial angular speed of the ball.

Write the expression for the moment of inertia of the ball

    I=23mr2

Write the expression for the initial angular speed of the ball

    ω1=v1r

Substitute 23mr2 for I and v1r for ω1 in equation (2).

    Kr1=12(23mr2)(v1r)2=13mv12

Write the expression for the translational kinetic energy of the ball at top point of the loop

    Kt2=12mv22

Here, v2 is the final linear velocity of the ball.

Write the expression for the rotational kinetic energy of the ball at top point of the loop

    Kr2=12Iω22        (3)

Here, ω2 is the initial angular speed of the ball.

Write the expression for the moment of inertia of the ball

    I=23mr2

Write the expression for the initial angular speed of the ball

    ω2=v2r

Substitute 23mr2 for I and v2r for ω2 in equation (2).

    Kr2=12(23mr2)(v2r)2=13mv22

Write the expression for the potential energy of the ball at top point of the loop

    U2=mg(2r)

Here, g is the acceleration due to gravity.

Substitute 12mv12 for Kt1, 13mv12 for Kr1, 12mv22 for Kt2, 13mv22 for Kr2 and mg(2r) for U2 in equation (1).

    12mv12+13mv12=12mv22+13mv22+mg(2r)

Simplify the above equation for v2.

    56mv22=56mv12mg(2r)v2=v1265g(2r)

Conclusion:

Substitute 9.8m/s2 for g, 45.0cm for r and 4.03m/s for v1 in above equation to find v2.

    v2=(4.03m/s)265×9.8m/s2×(2×45.0cm×102m1cm)=16.24m2/s210.58m2/s2=2.38m/s

Therefore, the speed of the ball at the top of the loop is 2.38m/s.

(b)

Expert Solution
Check Mark
To determine

The reason that the ball will not fall from the track at the top of the loop.

Answer to Problem 10.64P

The ball will not fall because the value of the centripetal acceleration is more than the acceleration due to gravity at the top point of the circular loop.

Explanation of Solution

The radius of the circular loop is 45.0cm, the height of the track from the horizontal section is 20.0cm and the initial velocity of the ball is 4.03m/s.

Formula to calculate the centripetal acceleration on the ball at the top of the loop

    a=(v2)2r

Here, a is the centripetal acceleration act on the ball at the top of the loop.

Substitute 2.38m/s for v2 and 45.0cm for r to find a.

    a=(2.38m/s)245.0cm×102m1cm=12.58m/s2

Thus, the centripetal acceleration act on the ball at the top of the loop is 12.58m/s2.

Since the centripetal acceleration at the top of the loop is more than the acceleration due to gravity that is (a>g) hence the ball remains on the track at top of the loop and will not fall.

Conclusion:

Therefore, the ball will not fall because the value of the centripetal acceleration is more than the acceleration due to gravity at the top point of the circular loop.

(c)

Expert Solution
Check Mark
To determine

The speed of the ball as it leaves the track at the bottom.

Answer to Problem 10.64P

The speed of the ball as it leaves the track at the bottom is 4.31m/s.

Explanation of Solution

The radius of the circular loop is 45.0cm, the height of the track from the horizontal section is 20.0cm and the initial velocity of the ball is 4.03m/s.

Write the expression for the law of energy conservation between horizontal track and the bottom of the loop

    Kt1+Kr1=Kt2+Kr2+U2        (4)

Here, Kt2 is the translational kinetic energy of the ball at bottom point of the loop, Kr2 is the rotational kinetic energy of the ball at bottom point of the loop and U2 is the potential energy of the ball at bottom point of the loop.

Write the expression for the translational kinetic energy of the ball at bottom point of the loop

    Kt3=12mv32

Here, v3 is the linear velocity of the ball at bottom.

Write the expression for the rotational kinetic energy of the ball at bottom point of the loop

    Kr3=12Iω32        (5)

Here,  ω3 is the initial angular speed of the ball.

Write the expression for the initial angular speed of the ball

    ω3=v3r

Substitute 23mr2 for I and v3r for ω3 in equation (5).

    Kr3=12(23mr2)(v3r)2=13mv32

Write the expression for the potential energy of the ball at top point of the loop

    U3=mgh

Here, g is the acceleration due to gravity and h is the height of the bottom track from the horizontal section.

Substitute 12mv12 for Kt1, 13mv12 for Kr1, 12mv32 for Kt3, 13mv32 for Kr3 and mgh for U3 in equation (4).

    12mv12+13mv12=12mv32+13mv32mgh

Simplify the above equation for v3.

    56mv32=56mv12+mghv3=v12+65gh

Conclusion:

Substitute 9.8m/s2 for g, 20.0cm for h and 4.03m/s for v1 in above equation to find v3.

    v3=(4.03m/s)2+65×9.8m/s2×20.0cm×102m1cm=16.24m2/s2+2.35m2/s2=4.31m/s

Thus, the speed of the ball as it leaves the track at the bottom is 4.31m/s.

(d)

Expert Solution
Check Mark
To determine

The speed of the ball at the top of the loop if ball slide instead of roll.

Answer to Problem 10.64P

The speed of the ball at the top of the loop is imaginary.

Explanation of Solution

Write the expression for the law of energy conservation between horizontal track and the top of the loop

    Kt1=Kt2'+U2'        (6)

Here, Kt1 is the translational kinetic energy of the ball at horizontal track, Kt2' is the new translational kinetic energy of the ball at top point of the loop and U2' is the new potential energy of the ball at top point of the loop.

Write the expression for the rotational kinetic energy of the ball at horizontal track

Write the expression for the new translational kinetic energy of the ball at top point of the loop

    Kt2=12m(v2')2

Here, v2' is the new linear velocity of the ball at the top point.

Write the expression for the new potential energy of the ball at top point of the loop

    U2'=mg(2r)

Substitute 12mv12 for Kt1, 12m(v2')2 for Kt2', and mg(2r) for U2 in equation (3).

    12mv12=12m(v2')2+mg(2r)

Simplify the above equation for v2.

    12m(v2')2=11mv12mg(2r)v2'=v122g(2r)

Substitute 9.8m/s2 for g, 45.0cm for r and 4.03m/s for v1 in above equation to find v2'.

    v2'=(4.03m/s)22×9.8m/s2×(2×45.0cm×102m1cm)=16.24m2/s217.64m2/s2=1.4m2/s2

Since the value inside the square root is negative that means the value is imaginary. This condition is impractical.

Thus, the speed of the ball at the top of the loop is imaginary.

Conclusion:

Therefore, the speed of the ball at the top of the loop is imaginary. It can’t be calculated.

(e)

Expert Solution
Check Mark
To determine

The explanation of the solution of part (d).

Answer to Problem 10.64P

The ball has not sufficient energy to arrive at top of the circular loop.

Explanation of Solution

The velocity comes out to be imaginary in part (d) that indicates the situation in impossible because as the boll slide instead of rolling, the ball have only translational kinetic energy which is insufficient for the ball to reach the top point on the circular loop.

Thus, the ball did not arrive at the top point of the loop.

Conclusion:

Therefore, the ball has not sufficient energy to arrive at top of the circular loop.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Chapter 10 Solutions

EBK PHYSICS FOR SCIENTISTS AND ENGINEER

Ch. 10 - A grindstone increases in angular speed from 4.00...Ch. 10 - Suppose a cars standard tires are replaced with...Ch. 10 - Figure OQ10.6 shows a system of four particles...Ch. 10 - As shown in Figure OQ10.7, a cord is wrapped onto...Ch. 10 - A constant net torque is exerted on an object....Ch. 10 - Prob. 10.9OQCh. 10 - A toy airplane hangs from the ceiling at the...Ch. 10 - A solid aluminum sphere of radius R has moment of...Ch. 10 - Is it possible to change the translational kinetic...Ch. 10 - Must an object be rotating to have a nonzero...Ch. 10 - Suppose just two external forces act on a...Ch. 10 - Explain how you might use the apparatus described...Ch. 10 - Example 10.6 Angular Acceleration of a Wheel A...Ch. 10 - Explain why changing the axis of rotation of an...Ch. 10 - Suppose you have two eggs, one hard-boiled and the...Ch. 10 - Suppose you set your textbook sliding across a...Ch. 10 - (a) What is the angular speed of the second hand...Ch. 10 - One blade of a pair of scissors rotates...Ch. 10 - If you see an object rotating, is there...Ch. 10 - If a small sphere of mass M were placed at the end...Ch. 10 - Three objects of uniform densitya solid sphere, a...Ch. 10 - Which of the entries in Table 10.2 applies to...Ch. 10 - Figure CQ10.15 shows a side view of a childs...Ch. 10 - A person balances a meterstick in a horizontal...Ch. 10 - (a) Find the angular speed of the Earths rotation...Ch. 10 - A potters wheel moves uniformly from rest to an...Ch. 10 - During a certain time interval, the angular...Ch. 10 - A bar on a hinge starts from rest and rotates with...Ch. 10 - A wheel starts from rest and rotates with constant...Ch. 10 - A centrifuge in a medical laboratory rotates at an...Ch. 10 - An electric motor rotating a workshop grinding...Ch. 10 - A machine part rotates at an angular speed of...Ch. 10 - A dentists drill starts from rest. After 3.20 s of...Ch. 10 - Why is the following situation impossible?...Ch. 10 - A rotating wheel requires 3.00 s to rotate through...Ch. 10 - The tub of a washer goes into its spin cycle,...Ch. 10 - A spinning wheel is slowed down by a brake, giving...Ch. 10 - Review. Consider a tall building located on the...Ch. 10 - A racing car travels on a circular track of radius...Ch. 10 - Make an order-of-magnitude estimate of the number...Ch. 10 - A discus thrower (Fig. P10.9) accelerates a discus...Ch. 10 - Figure P10.18 shows the drive train of a bicycle...Ch. 10 - A wheel 2.00 m in diameter lies in a vertical...Ch. 10 - A car accelerates uniformly from rest and reaches...Ch. 10 - A disk 8.00 cm in radius rotates at a constant...Ch. 10 - Prob. 10.22PCh. 10 - A car traveling on a flat (unbanked), circular...Ch. 10 - A car traveling on a flat (unbanked), circular...Ch. 10 - In a manufacturing process, a large, cylindrical...Ch. 10 - Review. A small object with mass 4.00 kg moves...Ch. 10 - Find the net torque on the wheel in Figure P10.14...Ch. 10 - The fishing pole in Figure P10.28 makes an angle...Ch. 10 - An electric motor turns a flywheel through a drive...Ch. 10 - A grinding wheel is in the form of a uniform solid...Ch. 10 - A 150-kg merry-go-round in the shape of a uniform,...Ch. 10 - Review. A block of mass m1 = 2.00 kg and a block...Ch. 10 - A model airplane with mass 0.750 kg is tethered to...Ch. 10 - A disk having moment of inertia 100 kg m2 is free...Ch. 10 - The combination of an applied force and a friction...Ch. 10 - Review. Consider the system shown in Figure P10.36...Ch. 10 - A potters wheela thick stone disk of radius 0.500...Ch. 10 - Imagine that you stand tall and turn about a...Ch. 10 - A uniform, thin, solid door has height 2.20 m,...Ch. 10 - Two balls with masses M and m are connected by a...Ch. 10 - Figure P10.41 shows a side view of a car tire...Ch. 10 - Following the procedure used in Example 10.7,...Ch. 10 - Three identical thin rods, each of length L and...Ch. 10 - Rigid rods of negligible mass lying along the y...Ch. 10 - The four particles in Figure P10.45 are connected...Ch. 10 - Many machines employ cams for various purposes,...Ch. 10 - A war-wolf or trebuchet is a device used during...Ch. 10 - A horizontal 800-N merry-go-round is a solid disk...Ch. 10 - Big Ben, the nickname for the clock in Elizabeth...Ch. 10 - Consider two objects with m1 m2 connected by a...Ch. 10 - The top in Figure P10.51 has a moment of inertia...Ch. 10 - Why is the following situation impossible? In a...Ch. 10 - In Figure P10.53, the hanging object has a mass of...Ch. 10 - Review. A thin, cylindrical rod = 24.0 cm long...Ch. 10 - Review. An object with a mass of m = 5.10 kg is...Ch. 10 - This problem describes one experimental method for...Ch. 10 - A uniform solid disk of radius R and mass M is...Ch. 10 - The head of a grass string trimmer has 100 g of...Ch. 10 - A cylinder of mass 10.0 kg rolls without slipping...Ch. 10 - A solid sphere is released from height h from the...Ch. 10 - (a) Determine the acceleration of the center of...Ch. 10 - A smooth cube of mass m and edge length r slides...Ch. 10 - A uniform solid disk and a uniform hoop are placed...Ch. 10 - A tennis ball is a hollow sphere with a thin wall....Ch. 10 - A metal can containing condensed mushroom soup has...Ch. 10 - As shown in Figure 10.13 on page 306, toppling...Ch. 10 - Review. A 4.00-m length of light nylon cord is...Ch. 10 - An elevator system in a tall building consists of...Ch. 10 - A shaft is turning at 65.0 rad/s at time t = 0....Ch. 10 - A shaft is turning at angular speed at time t =...Ch. 10 - Review. A mixing beater consists of three thin...Ch. 10 - The hour hand and the minute hand of Big Ben, the...Ch. 10 - A long, uniform rod of length L and mass M is...Ch. 10 - A bicycle is turned upside down while its owner...Ch. 10 - A bicycle is turned upside down while its owner...Ch. 10 - Prob. 10.76APCh. 10 - Review. As shown in Figure P10.77, two blocks are...Ch. 10 - Review. A string is wound around a uniform disk of...Ch. 10 - The reel shown in Figure P10.79 has radius R and...Ch. 10 - A common demonstration, illustrated in Figure...Ch. 10 - A uniform solid sphere of radius r is placed on...Ch. 10 - Review. A spool of wire of mass M and radius R is...Ch. 10 - A solid sphere of mass m and radius r rolls...Ch. 10 - A thin rod of mass 0.630 kg and length 1.24 m is...Ch. 10 - Prob. 10.85APCh. 10 - Review. A clown balances a small spherical grape...Ch. 10 - A plank with a mass M = 6.00 kg rests on top of...Ch. 10 - As a gasoline engine operates, a flywheel turning...Ch. 10 - As a result of friction, the angular speed of a...Ch. 10 - To find the total angular displacement during the...Ch. 10 - A spool of thread consists of a cylinder of radius...Ch. 10 - A cord is wrapped around a pulley that is shaped...Ch. 10 - A merry-go-round is stationary. A clog is running...Ch. 10 - A uniform, hollow, cylindrical spool has inside...
Knowledge Booster
Background pattern image
Physics
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Text book image
Physics for Scientists and Engineers
Physics
ISBN:9781337553278
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Text book image
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Text book image
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Text book image
Physics for Scientists and Engineers, Technology ...
Physics
ISBN:9781305116399
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
What is Torque? | Physics | Extraclass.com; Author: Extraclass Official;https://www.youtube.com/watch?v=zXxrAJld9mo;License: Standard YouTube License, CC-BY