In the case of plane stress, where the in-plane principal strains are given by ε1 and ε2, show that the third principal strain can be obtained from
where v is Poisson’s ratio for the material.
To show that: The third principal strain can be obtained from
Answer to Problem 10.94RP
The third principal strain can be obtained from
Explanation of Solution
Given information:
The third principal strain
Explanation:
For the case of plane stress
Apply the normal strain in x direction as shown below.
Here, E is the modulus of elasticity,
Substitute 0 for
Multiply both sides of the Equation by
Apply the normal strain in y direction as shown below.
Substitute 0 for
Apply the normal strain in z direction as shown below.
Substitute 0 for
Adding Equation (1) and (2).
Substitute
Substitute
Therefore, the third principal strain can be obtained from
Want to see more full solutions like this?
Chapter 10 Solutions
CODE/MINES MECHANICS MATERIALS >IC<
Additional Engineering Textbook Solutions
Heating Ventilating and Air Conditioning: Analysis and Design
Degarmo's Materials And Processes In Manufacturing
DESIGN OF MACHINERY
Foundations of Materials Science and Engineering
Engineering Mechanics: Statics
Vector Mechanics For Engineers
- An air-filled rubber ball has a diameter of 6 in. If the air pressure within the ball is increased until the diameter becomes 7 in., determine the average normal strain in the rubber.arrow_forwardThe prismatic bar has a cross-sectional area A. If it is subjected to a distributed axial loading that increases linearly from w = 0 at x = 0 to w = w0 at x = a, and then decreases linearly to w = 0 at x = 2a, determine the average normal stress in the bar as a function of x for a 6 x … 2a.arrow_forwardThe pin-connected rigid rods AB and BC are inclined at u = 30° when they are unloaded. When the force P is applied u becomes 30.2°. Determine the average normal strain in wire AC.arrow_forward
- A single strain gage, placed in the vertical plane on the outer surface and at an angle 60° to the axis of the pipe, gives a reading at point A of PA = -250(10-6). Determine the principal strains in the pipe at this point. The pipe has an outer diameter of 1 in. and an inner diameter of 0.6 in. and is made of C86100 bronze.arrow_forwardWhen the state of strain is represented by the principal strains, no shear strain will act on the element. True or False?arrow_forwardThe polysulfone block is glued at its top and bottom to the rigid plates. If a tangential force, applied to the top plate, causes the material to deform so that its sides are described by the equation y = 3.56 x1>4, determine the shear strain at the corners A and B.arrow_forward
- The strain at point A on the bracket has components P x = 300(10-6 ), Py = 550(10-6 ), gxy = -650(10-6 ), P z = 0. Determine (a) the principal strains at A in the x9y plane, (b) the maximum shear strain in the x–y plane, and (c) the absolute maximum shear strain.arrow_forwardThe triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5 mm. Determine the shear strain, gxy, at A.arrow_forwardBefore loading the plate, mark a line with the inclination shown. After the load is applied, the slope of the line decreases by 5x10^-3 rad. Determine the normal stress ?. Consider E = 2.1x106 kgf/cm^2 and v = 0.30. Express your answer in units of kgf/cm^2.arrow_forward
- The strain at point A on the pressure-vessel wall has components Px = 480(10-6), Py = 720(10-6), gxy =650(10-6). Determine (a) the principal strains at A, in the x9y plane, (b) the maximum shear strain in the x9y plane, and (c) the absolute maximum shear strain.arrow_forwardThe strain at point A on the bracket has normal components 250x10-6 and 550x10-6 in x and y directions, respectively and shear component -600 x10-6 in x-y plane. Determine the absolute maximum shear strain in 10-6 unit.arrow_forwardDetermine the equivalent state of strain on an element at the same point oriented 30∘∘ clockwise with respect to the original element. ϵx′, ϵy′,γx′y′ =arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY