Concept explainers
When tightening a bolt, mechanics sometimes extend the length of a wrench handle by slipping a section of pipe over the handle. Why could this procedure easily damage the bolt?
The reason for which extending the length of a wrench handle by slipping a section of pipe over the handle make the bolt damage easily.
Answer to Problem 1CQ
The increased length of the wrench handle results the increased torque to act on the bolt, which in turn shear and damage the bolt.
Explanation of Solution
The length of the wrench handle and the torque applied on the bolt is directly proportional. Increasing the length of the wrench handle will increase the torque being applied on the bolt.
This occurs due to the increase in the moment arm while increasing the length of the wrench handle.
The bolt is designed to withstand a particular amount of torque applied on it. The increased torque due to the increased length of the wrench handle will shear the bolt.
Want to see more full solutions like this?
Chapter 10 Solutions
EBK COLLEGE PHYSICS
Additional Science Textbook Solutions
Sears And Zemansky's University Physics With Modern Physics
Cosmic Perspective Fundamentals
Physics for Scientists and Engineers with Modern Physics
Conceptual Physics (12th Edition)
Glencoe Physical Science 2012 Student Edition (Glencoe Science) (McGraw-Hill Education)
- Answer yes or no to the following questions. (a) Is it possible to calculate the torque acting on a rigid object without specifying an axis of rotation? (b) Is the torque independent of the location of the axis of rotation?arrow_forwardThe fishing pole in Figure P10.22 makes an angle of 20.0 with the horizontal. What is the torque exerted by the fish about an axis perpendicular to the page and passing through the anglers hand if the fish pulls on the fishing line with a force F=100N at an angle 37.0 below the horizontal? The force is applied at a point 2.00 m from the anglers hands. Figure P10.22arrow_forwardA crane of mass m1 = 3 000 kg supports a load of mass m2 = 10 000 kg as shown in Figure P10.36. The crane is pivoted with a frictionless pin at A and rests against a smooth support at B. Find the reaction forces at (a) point A and (b) point B. Figure P10.36arrow_forward
- In analyzing the equilibrium of a flat, rigid object, you are about to choose an axis about which you will calculate torques. Which of the following describes the choice you should make? (a) The axis should pass through the objects center of mass. (b) The axis should pass through one end of the object. (c) The axis should be either the x axis or the y axis. (d) The axis should pass through any point within the object. (e) Any axis within or outside the object can be chosen.arrow_forwardA force of F=(2.00i+3.00j) N is applied to an object that is pivoted about a fixed axle aligned along the z coordinate axis. The force is applied at the point r=(4.00i+5.00j)m. Find (a) the magnitude of the net torque about the z axis and (b) the direction of the torque vector .arrow_forward(a) Give an example in which the net force acting on an object is zero and yet the net torque is nonzero, (h) (five an example in which the net torque acting on an object is zero and yet the net force is nonzero.arrow_forward
- To get up on the roof, a person (mass 70.0 kg) places a 6.00-m aluminum ladder (mass 10.0 kg) against the house on a concrete pad with the base of the ladder 2.00 m from the house. The ladder rests against a plastic rain gutter, which we can assume to be frictionless. The center of mass of the ladder is 2 m from the bottom. The person is standing 3 m from the bottom. What are the magnitudes of the forces on the ladder at the top and bottom?arrow_forwardThe fishing pole in Figure P10.28 makes an angle of 20.0 with the horizontal. What is the torque exerted by the fish about an axis perpendicular to the page and passing through the anglers hand if the fish pulls on the fishing line with a force F = 100 N at an angle 37.0 below the horizontal? The force is applied at a point 2.00 in from the anglers hands.arrow_forwardBIO When a gymnast performing on the rings executes the iron cross, he maintains the position at rest shown in Figure P10.85a. In this maneuver, the gymnasts feet (not shown) are off the floor. The primary muscles involved in supporting this position are the latissimus dorsi (lats) and the pectoralis major (pecs). One of the rings exerts an upward fore Fh on a hand as shown in Figure P10.85b. The force Fs is exerted by the shoulder joint on the arm. The latissimus dorsi and pectoralis major muscles exert a total force Fm on the arm. (a) Using the information in the figure, find the magnitude of the force Fm. (b) Suppose an athlete in training cannot perform the iron cross but can hold a position similar to the figure in which the arms make a 45 angle with the horizontal rather than being horizontal. Why is this position easier for the athlete? Figure P10.85arrow_forward
- As shown in Figure OQ10.9, a cord is wrapped onto a cylindrical reel mounted on a fixed, frictionless, horizontal axle. When does the reel have a greater magnitude of angular acceleration? (a) When the cord is pulled down with a constant force of 50 N. (b) When an object of weight 50 N is hung from the cord and released. (c) The angular accelerations in parts (a) and (b) are equal. (d) It is impossible to determine. Figure OQ10.9arrow_forwardWhen tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of 0.140 m from the center of the bolt. How much torque are you exerting in newton-meters (relative to the center of the bolt)?arrow_forwardThe cylindrical head bolts on a car are to be tightened with a torque of 62.0Nm . If a mechanic uses a wrench of length 20 cm, what perpendicular force must he exert on the end of the wrench to tighten a bolt correctly?arrow_forward
- University Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice UniversityPrinciples of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- College PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax CollegeGlencoe Physics: Principles and Problems, Student...PhysicsISBN:9780078807213Author:Paul W. ZitzewitzPublisher:Glencoe/McGraw-HillPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning