A spring of constant 15 kN/m connects points C and F of the linkage shown. Neglecting the weight of the spring and linkage, determine the force in the spring and the vertical motion of point G when a vertical downward 120-N force is applied (a) at point C, (b) at points C and H.
Fig. P10.5 and P10.6
(a)
Find the force in the spring and the vertical motion of point G when a vertical load of
Answer to Problem 10.5P
The force in the spring is
The vertical motion of point G is
Explanation of Solution
Given information:
The spring constant is
Calculation:
Show the free-body diagram of the spring assembly as in Figure 1.
Write the relation of the deflections at point G, H, F, E, D with C as follows;
The deflection
Assume the spring force Q is in tension.
Find the force in the spring Q using the relation.
Here, the spring constant is k.
Substitute
Use the virtual work principle:
Here,
Substitute 120 N for C,
The spring force Q is in compression. The assumption is incorrect.
Therefore, the force in the spring is
Substitute –60 N for Q in Equation (1).
Find the vertical motion
Substitute –2 mm for
Therefore, the vertical motion of point G is
(b)
Find the force in the spring and the vertical motion of point G when a vertical load of
Answer to Problem 10.5P
The force in the spring is
The vertical motion of point G is
Explanation of Solution
Given information:
The spring constant is
Calculation:
Use the virtual work principle:
Here,
Substitute 120 N for C,
The spring force Q is in compression. The assumption is incorrect.
Therefore, the force in the spring is
Substitute –300 N for Q in Equation (1).
Find the vertical motion
Substitute –10 mm for
Therefore, the vertical motion of point G is
Want to see more full solutions like this?
Chapter 10 Solutions
Vector Mechanics for Engineers: Statics 11th Edition
- Three bars, two made of aluminum and one made of steel, support a rigid block. An object of weight W is dropped vertically from a distance h above the rigid block. Both steel and aluminum bars have cross-sectional area of 50 mm2 and length of 0.5 m. The elastic moduli for the aluminum and steel are 76 GPa and 184 GPa, respectively. a) If W=1000N and h=0.1m, determine whether the three bars are still safe to perform. b) If h=0.2m, determine the maximum weight that can be dropped without causing failure to the barsarrow_forward(a) Determine the maximum allowable horizontal span for a uniform cable with a weight per unit length of w if the tension in the cable is not to exceed a given value Tm. (b) Using the result of part a , determine the maximum span of a steel wire for which w = 0.25 lb/ft and Tm = 8000 lb.arrow_forwardA collar B with a weight of W can move freely along the vertical rod shown. The constant of the spring is k , and the spring is unstretched when 0 = 0. (a) Derive an equation in 0, w, k, and 1 that must be satisfied when the collar is in equilibrium. (b) Knowing that W = 300 N, 1 = 500 mm, and k = 800 N/m, determine the value of 0 corresponding to equilibrium.arrow_forward
- A cable is placed around three parallel pipes. Knowing that the coefficients of friction are μs= 0.25 and μk= 0.20, determine (a) the smallest weight W for which equilibrium is maintained, (b) the largest weight W that can be raised if pipe B is slowly rotated counterclockwise while pipes A and C remain fixed.arrow_forwardFrom mechanics of materials it is known that when a static load P is applied at the end B of a uniform metal rod fixed at end A, the length of the rod will increase by an amount δ=PL/AE, where L is the length of the undeformed rod, A is its cross- sectional area, and E is the modulus of elasticity of the metal. Knowing that L = 450 mm and E = 200 GPa and that the diameter of the rod is 8 mm, and neglecting the mass of the rod, determine (a) the equivalent spring constant of the rod, (b ) the frequency of the vertical vibrations of a block of mass m = 8 kg attached to end B of the same rod.arrow_forwardmodified book exercise: Vector Mechanics for Engineers: Statics and Dynamics (8th Edition) chapter 4 and exercise 12 Four boxes are placed on a 17,7 kg uniform wooden plank that rests on two trestles. Knowing that the masses of boxes B and D are 2.5 kg and 32 kg, determine, respectively, the range of values for the mass of box A so that the plate remains in equilibrium when box C is removed. answer 1 2 kg found ≤ma ≤ 196.4kg( I don't know if this is correct)arrow_forward
- Knowing that the coefficient of static friction is 0.30 between the rope and the horizontal pipe and that the smallest value of P for which equilibrium is maintained is 80 N, determine (a) the largest value of P for which equilibrium is maintained, (b) the coefficient of static friction between the rope and the vertical pipe.arrow_forwardA cable is placed around three parallel pipes. Two of the pipes are fixed and do not rotate; the third pipe is slowly rotated. Knowing that the coefficients of friction are μs= 0.25 and μk= 0.20, determine the largest weight W that can be raised (a) if only pipe A is rotated counterclockwise, (b) if only pipe C is rotated clockwise.arrow_forwardFrom mechanics of materials it is known that for a cantilever beam of constant cross section a static load P applied at end B will cause a deflection δB = PL3/3EI, where L is the length of the beam, E is the modulus of elasticity, and I is the moment of inertia of the cross-sectional area of the beam. Knowing that L = 10 ft, E = 29 x 106 lb/in2, and I = 12.4 in4, determine (a) the equivalent spring constant of the beam, (b) the frequency of vibration of a 520-lb block attached to end B of the same beam.arrow_forward
- Knowing that the radius of each pulley is 200 mm and neglecting friction. determine the internal forces at point K of the frame shown.Fig. P7.18arrow_forwardTwo slender rods of negligible weight are pin-connected at C and attached to blocks A and B , each with a weight W . Knowing that P = 1.260 W and that the coefficient of static friction between the blocks and the horizontal surface is 0.30, determine the range of values of 0 between 0 and 180° for which equilibrium is maintained.arrow_forward6.107 a)The magnitude of the minimum force by surgeon's hands that will not allow the surgeon to move downward is _____lb. b) Assume the minimum force by the surgeon's hands is applied that will not allow the surgeon to move downward. The magnitude of the internal force in the straight section of the rope between the seat and the limb is _____lb. c) Assume an additional loop is placed around the limb. The magnitude of the minimum force by surgeon's hands that will not allow the surgeon to move downward is _____lb. d) Assume an additional loop is placed around the limb. Assume the minimum force by the surgeon's hands is applied that will not allow the surgeon to move downward. The magnitude of the internal force in the straight section of the rope between the seat and the limb is _____lb.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY