Concept explainers
For the case of plane stress, show that Hooke’s law can be written as
Trending nowThis is a popular solution!
Learn your wayIncludes step-by-step video
Chapter 10 Solutions
STANDALONE CODE MECHANICS OF MATERIALS-M
Additional Engineering Textbook Solutions
Applied Statics and Strength of Materials (6th Edition)
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Engineering Mechanics: Statics
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Statics and Mechanics of Materials (5th Edition)
Applied Fluid Mechanics (7th Edition)
- Determine the transverse strain in the x axis of the solid subjected to longitudinal tension. 4 cm 1 cm 6x10³ N 2 cm μ = 0,28 E=1,4x10" N/m² 6x10³ Narrow_forwardThe state of plane strain on an element is represented by the following components: Ex =D340 x 10-6, ɛ, = , yxy Ey =D110 x 10-6, 3D180 x10-6 ху Draw Mohr's circle to represent this state of strain. Use Mohrs circle to obtain the principal strains and principal plane.arrow_forwardA 23 mm diameter bronze bar 2.8 m long is placed between two rigid walls. At a temperature of -3°C, the gap Δ = 4.6 mm. Find the temperature(at degree-Celsius) at which the compressive stress in the bar will be 34 MPa. Use α = 18.09 × 10-6 m/(m·°C) and E = 82 GPa. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.arrow_forward
- 8000 mm3 aluminium cube is stressed in 3 mutually perpendicular direction x,y and z. The stresses in these directions are σx = 50 kPaσy = 80 kPaσz = -100 kPaDetermine the volumetric strain and change in volume. ν is 0.34 and E is 71 GPaarrow_forwardA displacement field in a body is given by u =c(x' +10) v = 2cyz =(-xy+2') w = where c = 104. Determine the state of strain and stress on an element positioned at (0, 2, 1). Use E = 70 GPa and v 0.3.arrow_forwardA 60 ̊ strain rosette measures the following strain at a point on the aluminum skin of an airplane. ε0 = 160 ×10-6 m/m, ε60 = -220 ×10-6 m/m and ε120 = 360 ×10-6 m/m. Using E= 10 ×106 psi and v = 0.3, Determine the principle stresses and the maximum in-plane shear stress.arrow_forward
- A rectangular aluminum plate of uniform thickness has a strain gauge at the center. It is placed in a test rig which can apply a biaxial force system along the edges of the plate as shown below. If the measured strains are +0.0005 and +0.001 in the x and y directions respectively, a) Determine the corresponding stresses set up in the plate and the strain through the thickness, εz. Take E=72 GPa and ν=0.32. b) Construct the Mohr’s circle for the loaded plate. c) State the values of the principal stresses. d) Determine the maximum shearing stresses and the directions of the planes on which they occur.arrow_forwardFor some element, the displacement is obtained as u = [1 + 3x +4y +5xy]x10^(-3) mm. The normal strain along x-axis at point (1.2, 0.8) m located inside the element isarrow_forwardThe normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression γy/3E where γ = 2.9 lb/in.3 is the specific weight of the material, y = 3.4 in. is the distance from the free (i.e., bottom) end of the bar, L = 17 in. is the length of the bar, and E = 24000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar. (c) the maximum normal strain in the bar.arrow_forward
- Three strain gauges are attached on the surface of the plane frame which is shown in Figure. The angle between each strain gauges are θº=63º. Reading from these gauges are: εa= 1100 μ, εb =335 μ and εc = -240 μCalculate:(a) The principal strains(b) The maximum shear strainarrow_forwardThe principal stresses for a certain state of stress are σ1 = 30 kPa, σ2 = 20 kPa, σ3 = 10 kPa.Find the magnitude of the normal and shear stresses on a plane defined by the normal vector,n = [1/2, 1/2, 1/√2] with respect to principal coordinates.arrow_forwardThe deviatoric principal strains at a point in a loaded member are ₁, 2, 3. Show that ₁ + ₂ + 3 = 0 (ej)² + (e₂)² + (ez)² = [(e₁ = €₂)² + (€2 − €3)² + (€3 − €₁)²] -arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY