THERMODYNAMICS (LL)-W/ACCESS >IP<
THERMODYNAMICS (LL)-W/ACCESS >IP<
9th Edition
ISBN: 9781260666557
Author: CENGEL
Publisher: MCG CUSTOM
bartleby

Videos

Textbook Question
Book Icon
Chapter 10.9, Problem 98RP

Consider a steam power plant that operates on a regenerative Rankine cycle and has a net power output of 150 MW. Steam enters the turbine at 10 MPa and 500°C and the condenser at 10 kPa. The isentropic efficiency of the turbine is 80 percent, and that of the pumps is 95 percent. Steam is extracted from the turbine at 0.5 MPa to heat the feedwater in an open feedwater heater. Water leaves the feedwater heater as a saturated liquid. Show the cycle on a T-s diagram, and determine (a) the mass flow rate of steam through the boiler and (b) the thermal efficiency of the cycle. Also, determine the exergy destruction associated with the regeneration process. Assume a source temperature of 1300 K and a sink temperature of 303 K.

(a)

Expert Solution
Check Mark
To determine

The mass flow rate of steam through the boiler.

Answer to Problem 98RP

The mass flow rate of steam through the boiler is 159.7kg/s.

Explanation of Solution

Draw the Ts diagram of the given regenerative Rankine cycle as shown in Figure 1.

THERMODYNAMICS (LL)-W/ACCESS >IP<, Chapter 10.9, Problem 98RP

Here, water (steam) is the working fluid of the regenerative Rankine cycle. The cycle involves two pumps.

Write the formula for work done by the pump during process 1-2.

wpI,in=v1(P2P1)ηP (I)

Here, the specific volume is v, the pressure is P, the isentropic efficiency of the pump is ηP, and the subscripts 1 and 2 indicates the process states.

Write the formula for enthalpy (h) at state 2.

h2=h1+wpI,in (II)

Write the formula for work done by the pump during process 3-4.

wpII,in=v3(P4P3)ηP (III)

Here, the specific volume is v, the pressure is P, and the subscripts 3 and 4 indicates the process states.

Write the formula for enthalpy (h) at state 4.

h4=h3+wpII,in (IV)

At state 6s:

The steam expanded to the pressure of 0.5MPa(500kPa) and the steam is at the state of saturated mixture.

The quality of water at state 6s is expressed as follows.

x6s=s6ssf,6ssfg,6s (V)

The enthalpy at state 6s is expressed as follows.

h6s=hf,6s+x6shfg,6s (VI)

Here, the enthalpy is h, the entropy is s, the quality of the water is x, the suffix f indicates the fluid condition, the suffix fg indicates the change of vaporization phase; the subscript 6s indicates the ideal process state 6s.

The isentropic efficiency for the process 5-6 is expressed as follows.

ηT=h5h6h5h6sh6=h5ηT(h5h6s) (VII)

At state 7s:

The steam enters the condenser at the pressure of 10kPa and at the state of saturated mixture.

The quality of water at state 7s is expressed as follows.

x7s=s7ssf,7ssfg,7s (VIII)

The enthalpy at state 7s is expressed as follows.

h7s=hf,7s+x7shfg,7s (IX)

Here, the subscript 7s indicates the ideal process state 7s.

The isentropic efficiency for the process 5-7 is expressed as follows.

ηT=h5h7h5h7sh7=h5ηT(h5h7s) (X)

Here, the subscript 6s, and 7s indicates the ideal process states; all other subscripts such as 1, 2, 3, 4, 5, 6 and 7 indicates the actual process states.

Write the formula for heat in (qin) and heat out (qout) of the cycle.

qin=h5h4 (XI)

qout=(1y)(h7h1) (XII)

Here, the mass fraction steam extracted from the turbine to the inlet mass of the boiler (m˙6/m˙3) is y.

Write the general equation of energy balance equation.

E˙inE˙out=ΔE˙system (XIII)

Here, the rate of net energy inlet is E˙in, the rate of net energy outlet is E˙out and the rate of change of net energy of the system is ΔE˙system.

At steady state the rate of change of net energy of the system (ΔE˙system) is zero.

ΔE˙system=0

Refer Equation (XIII).

Write the energy balance equation for open feed water heater.

E˙inE˙out=0E˙in=E˙outm˙inhin=m˙outhoutm˙6h6+m˙2h2=m˙3h3 (XIV)

Rewrite the Equation (XIV) in terms of mass fraction y.

yh6+(1y)h2=1h3yh6+h2yh2=h3y(h6h2)=h3h2y=h3h2h6h2 (XV)

Write the formula for net work output of the cycle.

wnet=qinqout (XVI)

Write the formula for mass flow rate of steam.

m˙=W˙netwnet (XVII)

Here, the net power output of the cycle is W˙net.

At state 1: (Pump I inlet)

The water exits the condenser as a saturated liquid at the pressure of 10kPa. Hence, the enthalpy, specific volume, and entropy at state 1 is as follows.

h1=hf@10kPav1=vf@10kPas1=sf@10kPa

Refer Table A-5, “Saturated water-Pressure table”.

The enthalpy (h1), specific volume (v1) and entropy (s1) at state 1 corresponding to the pressure of 10kPa is 191.81kJ/kg, 0.001010m3/kg, and 0.6492kJ/kgK respectively.

At state 3: (Pump II inlet)

The water exits the open feed water heater as a saturated liquid at the pressure of 0.5MPa(500kPa). Hence, the enthalpy, specific volume, and entropy at state 3 is as follows.

h3=hf@500kPav3=vf@500kPas3=sf@500kPa

Refer Table A-5, “Saturated water-Pressure table”.

The enthalpy (h3), specific volume (v3), and entropy (s3) at state 3 corresponding to the pressure of 0.5MPa(500kPa) is 640.09kJ/kg, 0.001093m3/kg, and 1.8604kJ/kgK respectively.

At state 5:

The steam enters the turbine as superheated vapor.

Refer Table A-6, “Superheated water”.

The enthalpy (h5) and entropy (s5) at state 5 corresponding to the pressure of 10MPa(10000kPa) and the temperature of 500°C is as follows.

h5=3375.1kJ/kgs5=6.5995kJ/kgK

Refer Figure 1.

s5=s6s=s7s=6.5995kJ/kgK

At state 6s:

The steam expanded to the pressure of 0.5MPa(500kPa) and in the state of saturated mixture.

Refer Table A-5, “Saturated water-Pressure table”.

Obtain the following properties corresponding to the pressure of 0.5MPa(500kPa).

hf,6s=640.09kJ/kghfg,6s=2108.0kJ/kgsf,6s=1.8604kJ/kgKsfg,6s=4.9603kJ/kgK

At state 7s:

The steam enters the condenser at the pressure of 10kPa and at the state of saturated mixture.

Refer Table A-5, “Saturated water-Pressure table”.

Obtain the following properties corresponding to the pressure of 10kPa.

hf,7s=191.81kJ/kghfg,7s=2392.1kJ/kgsf,7s=0.6492kJ/kgKsfg,7s=7.4996kJ/kgK

Conclusion:

Substitute 0.001010m3/kg for v1, 10kPa for P1, 500kPa for P2, and 0.95 for ηP in Equation (I).

wpI,in=(0.001010m3/kg)(500kPa10kPa)0.95=0.5209kPam3/kg×1kJ1kPam3=0.52kJ/kg

Substitute 191.81kJ/kg for h1, and 0.52kJ/kg for wpI,in in Equation (II).

h2=191.81kJ/kg+0.52kJ/kg=192.33kJ/kg

Substitute 0.001093m3/kg for v3, 500kPa for P3, 10000kPa for P4, and 0.95 for ηP in Equation (III).

wpII,in=(0.001093m3/kg)(10000kPa500kPa)0.95=10.93kPam3/kg×1kJ1kPam3=10.93kJ/kg

Substitute 640.09kJ/kg for h3, and 10.93kJ/kg for wpII,in in Equation (IV).

h4=640.09kJ/kg+10.93kJ/kg=651.02kJ/kg

From Figure 1.

s5=s6s=s7s=6.5995kJ/kgK

Substitute 6.5995kJ/kgK for s6, 1.8604kJ/kgK for sf,6s, and 4.9603kJ/kgK for sfg,6s in Equation (V).

x6s=6.5995kJ/kgK1.8604kJ/kgK4.9603kJ/kgK=0.9554

Substitute 640.09kJ/kg for hf,6s, 2108.0kJ/kg for hfg,6s, and 0.9554 for x6s in

Equation (VI).

h6s=640.09kJ/kg+0.9554(2108.0kJ/kg)=640.09kJ/kg+2013.9832kJ/kg=2654.0732kJ/kg

Substitute 3375.1kJ/kg for h5, 0.80 for ηT, 2654.0732kJ/kg for h6s in Equation (VII).

h6=3375.1kJ/kg0.80(3375.1kJ/kg2654.0732kJ/kg)=3375.1kJ/kg576.8214kJ/kg=2798.2786kJ/kg2798.3kJ/kg

Substitute 6.5995kJ/kgK for s7s, 0.6492kJ/kgK for sf,7s, and 7.4996kJ/kgK for sfg,7s in Equation (VIII).

x7s=6.5995kJ/kgK0.6492kJ/kgK7.4996kJ/kgK=0.7934

Substitute 191.81kJ/kg for hf,7s, 2392.1kJ/kg for hfg,7s, and 0.7934 for x7s in

Equation (IX).

h7s=191.81kJ/kg+0.7934(2392.1kJ/kg)=191.81kJ/kg+1897.8921kJ/kg=2089.7021kJ/kg2089.7kJ/kg

Substitute 3375.1kJ/kg for h5, 0.80 for ηT, 2089.7kJ/kg for h7s in Equation (X).

h7=3375.1kJ/kg0.80(3375.1kJ/kg2089.7kJ/kg)=3375.1kJ/kg1028.32kJ/kg=2346.78kJ/kg2346.8kJ/kg

Substitute 640.09kJ/kg for h3, 192.33kJ/kg for h2, and 2798.3kJ/kg for h6 in Equation (XV).

y=640.09kJ/kg192.33kJ/kg2798.3kJ/kg192.33kJ/kg=447.762605.97=0.1718

Substitute 3375.1kJ/kg for h5, and 651.02kJ/kg for h4 in Equation (XI).

qin=3375.1kJ/kg651.02kJ/kg=2724.08kJ/kg2724.1kJ/kg

Substitute 2346.8kJ/kg for h7, 0.1718 for y, and 191.81kJ/kg for h1 in Equation (XII).

qout=(10.1718)(2346.8kJ/kg191.81kJ/kg)=0.8282(2154.99kJ/kg)=1784.7627kJ/kg=1784.7kJ/kg

Substitute 2724.1kJ/kg for qin, and 1784.7kJ/kg for qout in Equation (XVI).

wnet=2724.1kJ/kg1784.7kJ/kg=939.4kJ/kg

Substitute 150MW for W˙net and 939.4kJ/kg for wnet in Equation (XVII).

m˙=150MW939.4kJ/kg=150MW×103kJ/s1MW939.4kJ/kg=159.6764kg/s159.7kg/s

Thus, the mass flow rate of steam through the boiler is 159.7kg/s.

(b)

Expert Solution
Check Mark
To determine

The thermal efficiency of the cycle and the exergy destruction associated with the regeneration process.

Answer to Problem 98RP

The thermal efficiency of the cycle is 34.5% and the exergy destruction associated with the regeneration process is 39.25kJ/kg.

Explanation of Solution

Write the formula for thermal efficiency of the cycle (ηth).

ηth=1qoutqin (XVIII)

Write the formula for exergy destruction associated with the regeneration cycle.

xdestroyed, reheat=T0sgen=T0(mesemisi+qsurrT0)=T0[s3ys6(1y)s2] (XIX)

Here, the entropy generation is sgen, the entropy is s, the heat transferred to the surrounding is qsurr, the surrounding (sink) temperature is T0, and the subscripts 2, 3 and 6 indicates the process states.

Conclusion:

Substitute 2724.1kJ/kg for qin, and 1784.7kJ/kg for qout in Equation (XVIII).

ηth=11784.7kJ/kg2724.1kJ/kg=10.6551=0.3448×100=34.5%

Thus, the thermal efficiency of the cycle is 34.5%.

Consider the regeneration process- open feed water heater, process states 6,2,3.

Here, s1=s2=0.6492kJ/kgK.

Substitute 303K for T0, 1.8604kJ/kgK for s3, 0.1718 for y, 6.5995kJ/kgK for s6, and 0.6492kJ/kgK for s2 in Equation (XIX).

xdestroyed, reheat=303K(1.8604kJ/kgK(0.1718)(6.5995kJ/kgK)(10.1718)(0.6492kJ/kgK))=303K(0.1295kJ/kgK)=39.2475kJ/kg39.25kJ/kg

Thus, the exergy destruction associated with the regeneration process is 39.25kJ/kg.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Consider a steam power plant that operates on the ideal reheat Rankine cycle. The plant maintains the boiler at 5400 kPa, the reheat section 1100 kPa, and the condenser at 10 kPa. The mixture quality at the exit of both turbines is 94 %. Determine the following values. (1) The specific enthalpy at the exit of the high-pressure turbine. (2) The specific entropy at the exit of the high-pressure turbine. (3) The temperature at the inlet of the high-pressure turbine. (4) The temperature at the inlet of the low-pressure turbine. (5) The thermal efficiency of the cycle.
A steam power plant operating on the intermediate steam Rankine cycle produces a net power of 160 MW. Water vapor enters the turbine at a pressure of 15 MPa and a temperature of 600 oC, and the condenser at a pressure of 15 kPa. The isentropic efficiency of the turbine is 85 percent and the isentropic efficiency of the pumps is 90 percent. In order to heat the feed water, some steam is separated from the turbine at a pressure of 0.6 MPa and sent to the open feedwater heater and exits the heater as a saturated liquid. Accordingly, fill in the blanks below. (Pump 1 inlet will be considered as saturated liquid.)   a) The mass flow rate of the steam passing through the boiler is m5= ..... kg/s. b) The mass flow rate of the steam separated from the turbine to heat the feed water is m6= ...... kg/s. c) The heat entering the cycle is Qin = ...... kW. d) The heat released from the cycle is Qout = ...... kW. e) The power produced in the turbine is WTurbine= ...... kW. f) The power consumed in…
Consider a reheat-regenerative vapor power cycle with two feedwater heaters, a closed feedwater heater and an open feedwater heater. Steam enters the first turbine at 8000 kPa and 480oC and expands to 700 kPa. The steam is reheated to 440oC before entering the second turbine, where it expands to the condenser pressure of 8 kPa. Steam is extracted from the first turbine at 2000 kPa and fed to the closed feedwater heater.  The feedwater leaves the closed heater at 205oC and 8000 kPa and enters the boiler to complete the cycle. The condensate from the closed feedwater heater is throttled into the open feedwater heater. Steam extracted from the second turbine at 300 kPa is also fed into the open feedwater heater, which operates at 300 kPa. The stream exiting the open feedwater heater is saturated liquid at 300 kPa. The net power output of the cycle is 100 MW. If the working fluid experiences no irreversibilities as it passes through the turbines and pumps, determine: (a) mass flowrate of…

Chapter 10 Solutions

THERMODYNAMICS (LL)-W/ACCESS >IP<

Ch. 10.9 - How do actual vapor power cycles differ from...Ch. 10.9 - Compare the pressures at the inlet and the exit of...Ch. 10.9 - The entropy of steam increases in actual steam...Ch. 10.9 - Is it possible to maintain a pressure of 10 kPa in...Ch. 10.9 - A simple ideal Rankine cycle with water as the...Ch. 10.9 - A simple ideal Rankine cycle with water as the...Ch. 10.9 - A simple ideal Rankine cycle which uses water as...Ch. 10.9 - Consider a solar-pond power plant that operates on...Ch. 10.9 - Consider a 210-MW steam power plant that operates...Ch. 10.9 - Consider a 210-MW steam power plant that operates...Ch. 10.9 - A simple ideal Rankine cycle with water as the...Ch. 10.9 - A simple ideal Rankine cycle with water as the...Ch. 10.9 - A steam Rankine cycle operates between the...Ch. 10.9 - A steam Rankine cycle operates between the...Ch. 10.9 - A simple Rankine cycle uses water as the working...Ch. 10.9 - The net work output and the thermal efficiency for...Ch. 10.9 - A binary geothermal power plant uses geothermal...Ch. 10.9 - Consider a coal-fired steam power plant that...Ch. 10.9 - Show the ideal Rankine cycle with three stages of...Ch. 10.9 - Is there an optimal pressure for reheating the...Ch. 10.9 - How do the following quantities change when a...Ch. 10.9 - Consider a simple ideal Rankine cycle and an ideal...Ch. 10.9 - Consider a steam power plant that operates on the...Ch. 10.9 - Consider a steam power plant that operates on the...Ch. 10.9 - An ideal reheat Rankine cycle with water as the...Ch. 10.9 - Steam enters the high-pressure turbine of a steam...Ch. 10.9 - An ideal reheat Rankine cycle with water as the...Ch. 10.9 - A steam power plant operates on an ideal reheat...Ch. 10.9 - Consider a steam power plant that operates on a...Ch. 10.9 - Repeat Prob. 1041 assuming both the pump and the...Ch. 10.9 - Prob. 43PCh. 10.9 - Prob. 44PCh. 10.9 - How do open feedwater heaters differ from closed...Ch. 10.9 - How do the following quantities change when the...Ch. 10.9 - Cold feedwater enters a 200-kPa open feedwater...Ch. 10.9 - In a regenerative Rankine cycle. the closed...Ch. 10.9 - A steam power plant operates on an ideal...Ch. 10.9 - A steam power plant operates on an ideal...Ch. 10.9 - A steam power plant operates on an ideal...Ch. 10.9 - Consider an ideal steam regenerative Rankine cycle...Ch. 10.9 - Consider a steam power plant that operates on the...Ch. 10.9 - Consider a steam power plant that operates on the...Ch. 10.9 - Consider a steam power plant that operates on the...Ch. 10.9 - A steam power plant operates on an ideal...Ch. 10.9 - Repeat Prob. 1060, but replace the open feedwater...Ch. 10.9 - A steam power plant operates on an ideal...Ch. 10.9 - A simple ideal Rankine cycle with water as the...Ch. 10.9 - Prob. 64PCh. 10.9 - An ideal reheat Rankine cycle with water as the...Ch. 10.9 - Consider a steam power plant that operates on a...Ch. 10.9 - Prob. 67PCh. 10.9 - A steam power plant operates on an ideal...Ch. 10.9 - The schematic of a single-flash geothermal power...Ch. 10.9 - What is the difference between cogeneration and...Ch. 10.9 - Prob. 71PCh. 10.9 - Prob. 72PCh. 10.9 - Consider a cogeneration plant for which the...Ch. 10.9 - Steam is generated in the boiler of a cogeneration...Ch. 10.9 - A large food-processing plant requires 1.5 lbm/s...Ch. 10.9 - An ideal cogeneration steam plant is to generate...Ch. 10.9 - Steam is generated in the boiler of a cogeneration...Ch. 10.9 - Consider a cogeneration power plant modified with...Ch. 10.9 - Prob. 80PCh. 10.9 - Why is the combined gassteam cycle more efficient...Ch. 10.9 - The gas-turbine portion of a combined gassteam...Ch. 10.9 - A combined gassteam power cycle uses a simple gas...Ch. 10.9 - Reconsider Prob. 1083. An ideal regenerator is...Ch. 10.9 - Reconsider Prob. 1083. Determine which components...Ch. 10.9 - Consider a combined gassteam power plant that has...Ch. 10.9 - Prob. 89PCh. 10.9 - What is the difference between the binary vapor...Ch. 10.9 - Why is mercury a suitable working fluid for the...Ch. 10.9 - Why is steam not an ideal working fluid for vapor...Ch. 10.9 - By writing an energy balance on the heat exchanger...Ch. 10.9 - Prob. 94RPCh. 10.9 - Steam enters the turbine of a steam power plant...Ch. 10.9 - Consider a steam power plant operating on the...Ch. 10.9 - A steam power plant operates on an ideal Rankine...Ch. 10.9 - Consider a steam power plant that operates on a...Ch. 10.9 - Repeat Prob. 1098 assuming both the pump and the...Ch. 10.9 - Consider an ideal reheatregenerative Rankine cycle...Ch. 10.9 - Prob. 101RPCh. 10.9 - A textile plant requires 4 kg/s of saturated steam...Ch. 10.9 - Consider a cogeneration power plant that is...Ch. 10.9 - Prob. 104RPCh. 10.9 - Prob. 105RPCh. 10.9 - Reconsider Prob. 10105E. It has been suggested...Ch. 10.9 - Reconsider Prob. 10106E. During winter, the system...Ch. 10.9 - Prob. 108RPCh. 10.9 - Prob. 109RPCh. 10.9 - A steam power plant operates on an ideal...Ch. 10.9 - A Rankine steam cycle modified for reheat, a...Ch. 10.9 - Show that the thermal efficiency of a combined...Ch. 10.9 - Prob. 118RPCh. 10.9 - A solar collector system delivers heat to a power...Ch. 10.9 - Starting with Eq. 1020, show that the exergy...Ch. 10.9 - Consider a simple ideal Rankine cycle with fixed...Ch. 10.9 - Consider a simple ideal Rankine cycle. If the...Ch. 10.9 - Consider a simple ideal Rankine cycle with fixed...Ch. 10.9 - Consider a simple ideal Rankine cycle with fixed...Ch. 10.9 - Consider a steady-flow Carnot cycle with water as...Ch. 10.9 - Prob. 126FEPCh. 10.9 - Prob. 127FEPCh. 10.9 - A simple ideal Rankine cycle operates between the...Ch. 10.9 - Pressurized feedwater in a steam power plant is to...Ch. 10.9 - Consider a steam power plant that operates on the...Ch. 10.9 - Consider a combined gas-steam power plant. Water...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Plant Explained | Working Principles; Author: RealPars;https://www.youtube.com/watch?v=HGVDu1z5YQ8;License: Standard YouTube License, CC-BY