Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 11, Problem 15RQ
Which type of oil ring is slotted so that excess oil can pass through it?
- Cast iron
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
The piston rings are used to act as a seal between the piston and cylinder head
a.
FALSE
b.
TRUE
how are the ( Dismantling and Assembly) of plug valve ? in oil and gas
Perforating Gun creates holes in the casing string to connect the flow of formation fluid into the wellbore with cone-shaped explosive charges detonated inside.
Select one:
True
False
Chapter 11 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 11 - Explain how to use a micrometer to measure cam...Ch. 11 - What is the cylinder taper?Ch. 11 - Describe how to measure main bearing oil...Ch. 11 - Where does maximum cylinder bore wear occur and...Ch. 11 - What type of valve lifter automatically...Ch. 11 - List three types of compression rings.Ch. 11 - Most pistons used today are made of. cast iron...Ch. 11 - Cam bearings in OHV engines are typically which...Ch. 11 - Which of the following is not of concern when...Ch. 11 - True or False? Cylinder taper is the difference in...
Ch. 11 - What is the purpose of a thrust main bearing?Ch. 11 - Each halt' of a split bearing is made slightly...Ch. 11 - Prob. 13RQCh. 11 - Prob. 14RQCh. 11 - Which type of oil ring is slotted so that excess...Ch. 11 - When removing the balance shaft assembly:...Ch. 11 - After installing cam bearings: Technician A checks...Ch. 11 - Technician A says that a cylinder wall with too...Ch. 11 - Technician A uses a pry bar to stretch the timing...Ch. 11 - Technician A installs a cup-type core plug with...Ch. 11 - Technician A uses a micrometer to measure the...Ch. 11 - Technician A says that piston ring end gaps should...Ch. 11 - Technician A checks crankshaft oil clearance with...Ch. 11 - When removing the piston and rod assemblies from a...Ch. 11 - Technician A says that crankshaft counterweights...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- If oil is to be stored at temperatures lower than 20F, A. waxes in the oil can reduce the oil's ability to flow properly. B. kerosene can be added to lower the oil's pour point. C.Both A and B are correct. D. Neither A nor B is correct.arrow_forwardWhat should be done to the valve packing if the valve knob does not turn freely after it has been tightened to stop a leak?arrow_forwardWhat should be done with a leaking cylinder if the leak cannot be stopped?arrow_forward
- True or False? An oil with the classification of 5W-30 has the viscosity of both a 5- and 30-weight oil. The 5W means the oil has a viscosity of 5 when warm and a 30 rating when it is cold.arrow_forwardWhen conducting an oil pressure test: Technician A says that lower than normal pressure can be caused by faulty piston oil rings. Technician B says that lower than normal oil pressure can be caused by excessive engine bearing clearances. Who is correct? Technician A Both A and B Technician B Neither A nor Barrow_forwardWhich compressor type uses tapered, machined gear components to trap the gas for compression? A. Scroll B. Reciprocating C. Rotary D. Screwarrow_forward
- Why should the end of the gas filler rod be bent?arrow_forwardWhat material is typically not used to form a rear main bearing oil seal? Polyacrylate RTV Silicone synthetic rubber Vitonarrow_forwardTechnician A says that oil pan gaskets are often made of cork due to its ability to conform to small imperfections in the oil pan. Technician B says oil pan and valve cover gaskets are often MLS gaskets to account for the different expansion rates between components. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- What part of the circulating system has the maximum pressure drop across it? a. Drill pipe b. Surface line c. Drill collar d. Bit nozzlesarrow_forwardWater is more dense than cooking oil. A) TRUE B) FALSEarrow_forwardChoose correct answer: The compressor is used to increase the pressure of fluid-like air or grease. Select one: True Falsearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Properties of Fluids: The Basics; Author: Swanson Flo;https://www.youtube.com/watch?v=TgD3nEO1iCA;License: Standard YouTube License, CC-BY
Fluid Mechanics-Lecture-1_Introduction & Basic Concepts; Author: OOkul - UPSC & SSC Exams;https://www.youtube.com/watch?v=6bZodDnmE0o;License: Standard Youtube License