Engineering Fundamentals: An Introduction to Engineering
6th Edition
ISBN: 9780357112311
Author: Saeed Moaveni
Publisher: Cengage Learning US
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 11, Problem 34P
To determine
Find the heat-transfer rate of an electronic chip and also determine the R-factor.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Questions:
2nd: Calculate the thermal resistance (R or R₂) of human skin with a
thickness of 2 cm, per cm² of skin.
●
thermal conductivity=0.627 N/(°C.s)
●
• specific heat-c-3470 Nm/kg °C
• density=1100 kg/m³
Rt
-
L
KA
where
k is the materials conductivity [W.m³!.K-¹]
L is the plane thickness [m]
A is the plane area [m²]
A double-pane glass window consists of two pieces of glass, each having athickness of 8 mm, with a thermal conductivity of k = 1.4 W⁄m ⋅ K . The twoglass panes are separated by an air gap of 10 mm, as shown in Figure 11.10 .Assuming the thermal conductivity of air to be k = 0.025 W⁄m ⋅ K , determinethe total R-value for this window. The total thermal resistance of the window is obtained by adding the resistance offered by each pane of glass and the air gap in the following manner:
3. The temperature of an iron bar is 36°F. It is placed in an oven, after 1 and 2 minutes,
respectively, it reads 60°F and 820°F . What is the temperature in the oven?
Chapter 11 Solutions
Engineering Fundamentals: An Introduction to Engineering
Ch. 11.2 - Prob. 1BYGCh. 11.2 - Prob. 2BYGCh. 11.2 - Prob. 3BYGCh. 11.2 - Prob. 4BYGCh. 11.2 - Prob. 5BYGCh. 11.2 - Prob. BYGVCh. 11.4 - Prob. 1BYGCh. 11.4 - Prob. 2BYGCh. 11.4 - Prob. 3BYGCh. 11.4 - Prob. 4BYG
Ch. 11.4 - Prob. BYGVCh. 11.6 - Prob. 1BYGCh. 11.6 - Prob. 2BYGCh. 11.6 - Prob. 3BYGCh. 11.6 - Prob. 4BYGCh. 11.6 - Prob. BYGVCh. 11 - Prob. 1PCh. 11 - Prob. 2PCh. 11 - Alcohol thermometers can measure temperatures in...Ch. 11 - Prob. 4PCh. 11 - Prob. 5PCh. 11 - Prob. 6PCh. 11 - Prob. 7PCh. 11 - Prob. 8PCh. 11 - Calculate the R-value for the following materials:...Ch. 11 - Calculate the thermal resistance due to convection...Ch. 11 - Prob. 11PCh. 11 - Prob. 12PCh. 11 - Prob. 13PCh. 11 - Estimate the change in the length of a power...Ch. 11 - Calculate the change in 5 m long copper wire when...Ch. 11 - Prob. 16PCh. 11 - Prob. 17PCh. 11 - Prob. 19PCh. 11 - Prob. 20PCh. 11 - Prob. 23PCh. 11 - Prob. 24PCh. 11 - Prob. 26PCh. 11 - Prob. 27PCh. 11 - Prob. 28PCh. 11 - Prob. 29PCh. 11 - Prob. 30PCh. 11 - Prob. 31PCh. 11 - Prob. 32PCh. 11 - Prob. 33PCh. 11 - Prob. 34PCh. 11 - Prob. 35PCh. 11 - For Problems 11.11, 11.12, and 11.13, calculate...Ch. 11 - Prob. 37PCh. 11 - Prob. 38PCh. 11 - Prob. 39PCh. 11 - Prob. 40PCh. 11 - Prob. 41PCh. 11 - Prob. 42PCh. 11 - Prob. 43PCh. 11 - Prob. 44PCh. 11 - Prob. 45PCh. 11 - Prob. 46PCh. 11 - Prob. 47PCh. 11 - Prob. 48PCh. 11 - Prob. 49PCh. 11 - Prob. 51PCh. 11 - Prob. 52PCh. 11 - Prob. 53PCh. 11 - Prob. 54PCh. 11 - Prob. 55P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- a. What is shown in the figure? Where is it used and how does it work? b. What is the nature of heat exchange process, and why is this suitable? c. What is the relative direction of fluid motion?arrow_forwardFor the fin equation described in Problem 6.25, if the units of T, h, P, A, and x are expressed in degree Rankine (R), Btu/hr ft2R, ft, ft2, and ft, respectively, what is the appropriate unit for thermal conductivity k if the fin equation is to be homogeneous in units? Show all steps of your work.arrow_forwardCalculate the R-value for the following materials: a. 4 in. thick brick b. 10 cm thick brick c. 12 in. thick concrete slab d. 20 cm thick concrete slab e. 1 cm thick human fat layerarrow_forward
- A glass of a hot water has an initial temperature 80°C, placed in a room where the temperature is 30°C. After one minute the water temperature drops to 70°C. What will be the temperature after 3 minutes? At what time the water cools down to 40°C?arrow_forward9. A form is made to wind a coil. The allowances made for insulation are as follows: four layers 1/64 inch tape, two pieces of 4/64 inch fish paper, and two pieces of 3/8 inch fiber. What is the total thickness allowed for insulation?arrow_forwardCalculate the density of air at standard conditions (T - 25 °C and P a 1 atm).arrow_forward
- A glass windowpane in a home is 0.62 cm thick and has dimensions of 1.4 m x 1.9 m. On a certain day, the indoor temperatu 24°C and the outdoor temperature is 0°C. (a) What is the rate at which energy is transferred by heat through the glass? W (b) How much energy is lost through the window in one day, assuming the temperatures inside and outside remain constant?arrow_forward1.37 What is the specific weight of air at 70 psia and 70 °F?arrow_forwardPROBLEM 3. The assembly shown constructed from a steel bolt with a diameter of 8 mm and fits and a magnesium sleeve with an inner diameter of 10 mm and an outer diameter of 12 mm. The length of the sleeve is 150 mm. The assembly is originally at a temperature of T1 temperature is raised to a final value of T2 = 120°C. If there is gap of 0.1 mm between sleeve and the rigid washer at end B before the heating, determine the average normal stress in the bolt and the = 20°C and then the sleeve. Est = 200 GPa, Emg = 44.7 GPa, a,t = 14(10°)/°C, amg = 26(10)/"C. Rigid washers 150 mm 0,1 mmarrow_forward
- 5 Which one of the following is the unit of the ratio of dynamic viscosity to density? a. Stokes b. Pa-s c. N m2/s d. Poisearrow_forward3. According to Newton's Law of cooling', the rate at which the heat is lost by a heated body is proportional to the difference in temperature between the body and the surrounding medium (when the temperatutre difference is very small). If a thermometer is taken outdoor, where the temperature is 6°C, from a room which temperature is 25C, and the reading drops 15°C in one minute, how long after its removal from the room will the reading be 8°C? after 45 secs what is the thermometer reading?arrow_forwardHeat Transfer 1. If you have a piece of extruded polystyrene insulation that has an R-value of 5 hr ft?.°F/Btu per inch [or RSI = 0.8805 (m² · K)/W)]. How many inches of extruded polystyrene do you need in your wall if you want it to have an R-value of 20 hr ft2.°F/Btu [or RSI = 3.522 (m² · K)/W)]? L= 4" 2. What is the transfer of vibrational energy due to collisions between neighbouring atoms and molecules in a solid called? a. Conduction b. Convection c. Radiation d. Latent Heat Radiant Energy 3. Absorptance is a measure of the relative amount of radiant energy absorbed by a surface. Does a shiny and smooth polished aluminum surface have a high absorptance (closer to 1), or a low absortptance (closer to 0)? Absorptance is a ratio of the radiation absorbed to the radiation received, and thus is dimensionless. What about reflectance? Are absorptance and reflectance related? 4. Emissivity is a measure of the relative amount of radiant energy emitted by a surface. Does a shiny and smooth…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage Learning
Engineering Fundamentals: An Introduction to Engi...
Civil Engineering
ISBN:9781305084766
Author:Saeed Moaveni
Publisher:Cengage Learning