A baseball bat has a “sweet spot” where a ball can be hit with almost effortless transmission of energy. A careful analysis of baseball dynamics shows that this special spot is located at the point where an applied force would result in pure rotation of the bat about the handle grip. Determine the location of the sweet spot of the bat shown in Fig. 11–51. Tile linear mass density of the bat is given roughly by (0.61 + 3.3x2) kg/m, where x is in meters measured from the end of the handle. The entire bat is 0.84 m long. The desired rotation point should be 5.0 cm from the end where the bat is held. [Hint: Where is the CM of the bat?]
FIGURE 11–51 Problem 82.
Want to see the full answer?
Check out a sample textbook solutionChapter 11 Solutions
PHYSICS F/SCI.+ENGR.,V.1 (CHAP.1-20)
Additional Science Textbook Solutions
The Cosmic Perspective Fundamentals (2nd Edition)
The Cosmic Perspective
College Physics
Modern Physics
Physics for Scientists and Engineers: A Strategic Approach with Modern Physics (4th Edition)
Essential University Physics: Volume 1 (3rd Edition)
- A body moving in a circle with a constant seed is in rotational equilibrium.arrow_forward17-89. The "Catherine wheel" is a firework that consists of a coiled tube of powder which is pinned at its center. If the powder burns at a constant rate of 20 g/s such as that the exhaust gases always exert a force having a constant magnitude of 0.3 N, directed tangent to the wheel, determine the angular velocity of the wheel when 75% of the mass is burned off. Initially, the wheel is at rest and has a mass of 100 g and a radius of r=75 mm. For the calculation, consider the wheel to always be a thin disk. Co 0.3 Narrow_forward17-106. The truck carries the spool which has a weight of 500 Ib and a radius of gyration of kg = 2 ft. Determine the angular acceleration of the spool if it is not tied down on the truck and the truck begins to accelerate at 3 ft/s². Assume the spool does not slip on the bed of the truck.arrow_forward
- 20) A uniform wood beam (Wwood = 2,000 N and L=6 meter) has a load of bricks (Wbricks = 5,000 N) placed on the beam raricks 4 meters from the end, Bob (Waob = 1,000 N) is standing on the wood beam raob Im from the end. At what positions (d) measured from the far-left end of the board would the triangle be placed so that the system is balanced? Tricksarrow_forward52 O In Fig. 10-42, a cylinder having a mass of 2.0 kg can rotate about its central axis through point O. Forces are applied as shown: F = 6.0 N, F2 = 4.0N, F, = 2.0 N, and F4 = 5.0 N. Also, r = 5.0 cm and R = 12 cm. Find the (a) magnitude and (b) direction of the an- gular acceleration of the cylinder. (During the rotation, the forces maintain their same angles relative to the cylinder.) Rotation axis Figure 10-42 Problem 52.arrow_forwardn41 G0 In Fig. 10-37, two particles, each with mass m = 0.85 kg, are fas- tened to each other, and to a rotation axis at 0, by two thin rods, each with length d = 5.6 cm and mass M = 1.2 kg. The combination rotates M. Rotation axis around the rotation axis with the an- gular speed w = 0.30 rad/s. Measured about O, what are the combination's (a) rotational inertia and (b) kinetic energy? Figure 10-37 Problem 41.arrow_forward
- A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 620 kg and an average gear-tooth force of 2.15 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assumer-110 mm, R-615 mm, 0 = 25° Detail of contact at B Answer: mmarrow_forwardA cube of side l rests on a rough floor. It is subjected to a steady horizontal pull F, exerted a distance h above the floor as shown in Fig. 9-79. As Fis increased, the block will either begin to slide, or begin to tip over. Determine the coefficient of static friction us so that (a) the block begins to slide rather than tip; (b) the block begins to tip. [Hint: Where will the normal force on the block act if it tips?] h FIGURE 9–79 Problem 60.arrow_forwardTwo identical, uniform beams are symmetrically set up against each other (Fig. 9–87) on a floor with which they have a coefficient of fric- tion µs = 0.50. What is the minimum angle the beams can make with the floor and still not fall? FIGURE 9-87 Problem 71.arrow_forward
- (II) A potter’s wheel is rotating around a vertical axis through its center at a frequency of 1.5 rev/s. The wheel can be considered a uniform disk of mass 5.0 kg and diameter 0.40 m. The potter then throws a 2.6-kg chunk of clay,approximately shaped as a flat disk of radius 7.0 cm, onto the center of the rotating wheel. What is the frequency of the wheel after the clay sticks to it? Ignore friction.arrow_forwardFor the system to be in equilibrium the sum of clockwise and anticlockwise moments must be O Equal O Equal to the resultant force O Zero O Equal to resultant momentarrow_forward17-102. The 25-lb slender rod has a length of 6 ft. Using a collar of negligible mass, its end A is confined to move along the smooth circular bar of radius 3 V2 ft. End B rests on the floor, for which the coefficient of kinetic friction is µg = 0.4. If the bar is released from rest when 6 = 30°, determine the angular acceleration of the bar at this instant. 6 ft 3N2 ftarrow_forward
- Classical Dynamics of Particles and SystemsPhysicsISBN:9780534408961Author:Stephen T. Thornton, Jerry B. MarionPublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax CollegeUniversity Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice University