A baseball bat has a “sweet spot” where a ball can be hit with almost effortless transmission of energy. A careful analysis of baseball dynamics shows that this special spot is located at the point where an applied force would result in pure rotation of the bat about the handle grip. Determine the location of the sweet spot of the bat shown in Fig. 11–51. Tile linear mass density of the bat is given roughly by (0.61 + 3.3x2) kg/m, where x is in meters measured from the end of the handle. The entire bat is 0.84 m long. The desired rotation point should be 5.0 cm from the end where the bat is held. [Hint: Where is the CM of the bat?]
FIGURE 11–51 Problem 82.
Want to see the full answer?
Check out a sample textbook solutionChapter 11 Solutions
PHYSICS F/SCI.+ENGR.,CHAPTERS 1-37
Additional Science Textbook Solutions
The Cosmic Perspective Fundamentals (2nd Edition)
The Cosmic Perspective
College Physics
Modern Physics
Physics for Scientists and Engineers: A Strategic Approach with Modern Physics (4th Edition)
Essential University Physics: Volume 1 (3rd Edition)
- When there is a global heating trend on Earth, the atmosphere expands and the length of the day increases very slightly. Explain why the length of a day increases.arrow_forwardA body moving in a circle with a constant seed is in rotational equilibrium.arrow_forward12–159. The small washer is sliding down the cord OA. When it is at the midpoint, its speed is 28 m/s and its acceleration is 7 m/s?. Express the velocity and acceleration of the washer at this point in terms of its cylindrical components. 6 m 3 marrow_forward
- 17-106. The truck carries the spool which has a weight of 500 Ib and a radius of gyration of kg = 2 ft. Determine the angular acceleration of the spool if it is not tied down on the truck and the truck begins to accelerate at 3 ft/s². Assume the spool does not slip on the bed of the truck.arrow_forward; Calculate the M. I. of thin uniform rod of mass 10 g and length 60 cm about an axis through its centre and perpendicular to its length.arrow_forward20) A uniform wood beam (Wwood = 2,000 N and L=6 meter) has a load of bricks (Wbricks = 5,000 N) placed on the beam raricks 4 meters from the end, Bob (Waob = 1,000 N) is standing on the wood beam raob Im from the end. At what positions (d) measured from the far-left end of the board would the triangle be placed so that the system is balanced? Tricksarrow_forward
- 52 O In Fig. 10-42, a cylinder having a mass of 2.0 kg can rotate about its central axis through point O. Forces are applied as shown: F = 6.0 N, F2 = 4.0N, F, = 2.0 N, and F4 = 5.0 N. Also, r = 5.0 cm and R = 12 cm. Find the (a) magnitude and (b) direction of the an- gular acceleration of the cylinder. (During the rotation, the forces maintain their same angles relative to the cylinder.) Rotation axis Figure 10-42 Problem 52.arrow_forwardn41 G0 In Fig. 10-37, two particles, each with mass m = 0.85 kg, are fas- tened to each other, and to a rotation axis at 0, by two thin rods, each with length d = 5.6 cm and mass M = 1.2 kg. The combination rotates M. Rotation axis around the rotation axis with the an- gular speed w = 0.30 rad/s. Measured about O, what are the combination's (a) rotational inertia and (b) kinetic energy? Figure 10-37 Problem 41.arrow_forwardA large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 620 kg and an average gear-tooth force of 2.15 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assumer-110 mm, R-615 mm, 0 = 25° Detail of contact at B Answer: mmarrow_forward
- A cube of side l rests on a rough floor. It is subjected to a steady horizontal pull F, exerted a distance h above the floor as shown in Fig. 9-79. As Fis increased, the block will either begin to slide, or begin to tip over. Determine the coefficient of static friction us so that (a) the block begins to slide rather than tip; (b) the block begins to tip. [Hint: Where will the normal force on the block act if it tips?] h FIGURE 9–79 Problem 60.arrow_forward(II) A potter’s wheel is rotating around a vertical axis through its center at a frequency of 1.5 rev/s. The wheel can be considered a uniform disk of mass 5.0 kg and diameter 0.40 m. The potter then throws a 2.6-kg chunk of clay,approximately shaped as a flat disk of radius 7.0 cm, onto the center of the rotating wheel. What is the frequency of the wheel after the clay sticks to it? Ignore friction.arrow_forward2)8arrow_forward
- Classical Dynamics of Particles and SystemsPhysicsISBN:9780534408961Author:Stephen T. Thornton, Jerry B. MarionPublisher:Cengage LearningPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningPrinciples of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- Physics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning