Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
10th Edition
ISBN: 9780073398204
Author: Richard G Budynas, Keith J Nisbett
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 12, Problem 11P
A full journal bearing has a shaft diameter of 3.000 in with a unilateral tolerance of –0.0004 in. The l/d ratio is unity. The bushing has a bore diameter of 3.003 in with a unilateral tolerance of 0.0012 in. The SAE 40 oil supply is in an axial-groove sump with a steady-state temperature of 140°F. The radial load is 675 lbf. Estimate the average film temperature, the minimum film thickness, the heat loss rate, and the lubricant side-flow rate for the minimum clearance assembly, if the journal speed is 10 rev/s.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A full journal bearing has a nominal diameter of 60.0 mm, a bearing length of 30.0 mm and supports a load of 3200 N when running at the design speed of 3200 rpm. The radial clearance has been specified as 0.04 mm. An SAE 20 oil has been chosen and the lubricant supply system is capable of delivering the lubricant to the bearing at 60oC. Using the Raimondi and Body design charts;1.1 find the temperature rise of the lubricant, (19)1.2 the total flow rate required, (1)1.3 the torque required to overcome friction (3)1.4 and the power dissipated in the bearing.
15.)A full journal bearing has a journal diameter of 4.000in. with a unilateral tolerance of -0.004in. The bushing bore has a diameter of 4.004in and unilateral tolerance of +0.004in. the bearing is 3in long. The journal load is 3000 lbf and it runs at a speed of 400 rpm. What is the load per projected bearing area 9P) in psi?
Choose answer below
75
100
125
250
16.)For the bearing in problem #15, if the lubricant average viscosity is 9 ureym, what is the Sommerfield number (assuming minimum clearance)
Choose answer below
Between 0.6 and 0.7
Between 0.5 and 0.6
Between 0.3 and 0.4
Between 0.2 and 0.3
A pressure-fed bearing has a journal diameter of 75.00 mm with a unilateral tolerance of -0.05 mm. The bushing bore diameter is 75.084 mm with a unilateral tolerance of 0.010 mm.The length of the bushing is 62.00 mm. Its central annular groove is 12.00 mm wide and is fed by SAE 30 oil is 53 °C at 200 kPa supply gauge pressure. The journal speed is 2880 rev/min carrying a load of 30 kN. The sump can dissipate 300 watts per bearing if necessary. For minimum radial clearances, find:
the average temperature.
Given the film temperature is 85 o C
Chapter 12 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Ch. 12 - A full journal bearing has a journal diameter of...Ch. 12 - A full journal bearing has a journal diameter of...Ch. 12 - A journal bearing has a journal diameter of 3.000...Ch. 12 - Prob. 4PCh. 12 - Prob. 5PCh. 12 - Prob. 6PCh. 12 - Prob. 7PCh. 12 - Prob. 8PCh. 12 - A full journal bearing is 28 mm long. The shaft...Ch. 12 - A 114114 in sleeve bearing supports a load of 700...
Ch. 12 - A full journal bearing has a shaft diameter of...Ch. 12 - Prob. 12PCh. 12 - Prob. 13PCh. 12 - A natural-circulation pillow-block bearing with...Ch. 12 - An eight-cylinder diesel engine has a front main...Ch. 12 - A pressure-fed bearing has a journal diameter of...Ch. 12 - Design a central annular-groove pressure-fed...Ch. 12 - Repeat design problem Prob. 1218 using the nominal...Ch. 12 - Table 12-1 gives the Seireg and Dandage curve fit...Ch. 12 - For Prob. 1218 a satisfactory design is...Ch. 12 - An Oiles SP 500 alloy brass bushing is 0.75 in...Ch. 12 - Prob. 23P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Q 2. A journal bearing has a shaft diameter of 75.00 mm with a unilateral tolerance of −0.02 mm. The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 700 rev/min. For the minimum clearance assembly find the minimum film thickness, the heat loss rate, and the maximum lubricant pressure for SAE 30, SAE 40 and SAE 50 lubricants operating at an average film temperature of 60 °C.arrow_forwardThory of machine: Select one of the following bearing for the load conditions. Radial load, F=3000 N, Axial load, F = 1600 N, RPM = 1000. (1) Deep Groove ball bearing dynamic load rating=47000 N radial bad factor, X=0.56 Axial load factor, Y= 1.83 (i) Cylindrical roller bearing Dynamic load rating 28000 N radial load factor, X=1.0 axial load factor, Y=0.0arrow_forwardA single deep grove ball bearing series 3, the outer ring rotates at 1500 rpm with little shock load. Bearing has a bore diameter of 45 mm, working with a load 1890 lb radial and 1250 lb axial load. Determine the rated life and median life of the bearing. Use the design factors according to the attached table.arrow_forward
- Design a single row deep groove ball bearing with basic dynamic load rating of 25.5 KN to be used in a turbine to carry a radial load of 1607 N. The expected life of the bearing is 5226 hours at 523 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.8. The radial and axial load factors are 1.3 and 1.6 respectively and the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Axial load acting on the bearing in Narrow_forwardA full journal bearing has a journal diameter of 25 mm, with a unilateral tolerance of -0.03 mm. The bushing bore has a diameter of 25.03 mm and a unilateral tolerance of 0.04 mm. The 1/d ratio is 1/2. The load is 1.2 kN and the journal runs at 1100 rev/min. If the average viscos- ity is 55 mPa • s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.arrow_forwardA certain application requires a ball bearing with the inner ring rotating, with a design life of 26 kh at a speed of 455 rev/min. The radial load is 2.5 kN and an application factor of 1.2 is appropriate. The reliability goal is 0.92. Find the multiple of rating life required, xD , and the catalog rating C10 with which to enter a bearing table. Choose a 02-series deep-groove ball bearing from Table 11–2 and estimate the reliability in use.arrow_forward
- b) Design a single row deep groove ball bearing with basic dynamic load rating of 33 KN to be used in a turbine to carry a radial load of 1584 N. The expected life of the bearing is 5591 hours at 529 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.8. The radial and axial load factors are 1.3 and 1.6 respectively and the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Axial load acting on the bearing in Narrow_forwardA natural feed journal bearing of diameter 50mm and length 50mm operating at 20rev/s. Carries a load of 2KN. The lubricant used has a viscosity of 20MPa. The radial clearance is 50um. The Sommerfeld number for the bearing?arrow_forwardA connecting rod for an I.C. engine running at 1800 r.p.m. and developing a maximum pressure of 3.15 MPa. The diameter of the piston is 100 mm; mass of the reciprocating parts per cylinder 2.25 kg; length of connecting rod 380 mm; stroke of piston 190 mm and compression ratio 6:1. Take a factor of safety of 6 for the design. Take length to diameter ratio for big end bearing as 1.3 and small end bearing as 2 and the corresponding bearing pressures as 10 MPa and 15 MPa. The density of material of the rod may be taken as 8000 kg/m³ and the allowable stress in the bolts as 60 MPa and in cap as 80 MPa. The rod is to be of I-section for which you can choose your own proportions. Calculate the dimension of I- section of the connecting rod.arrow_forward
- A single row deep groove ball bearing is operating at a speed of 2000rpm acted upon by a radial load of 10kn and thrust load of 8kn. The bearing is subjected to light shock load and outer ring is rotating. Determine the life rating of the bearingarrow_forwardA propeller shaft rotating at constant speed is subjected to variable loads.Ball bearing supporting the shaft are subject to variable radial loads as follows;16KN for 40 percent of the time,2KN for 10 percent of the time,4KN for 20percent of the time and no load for the remaining time of the cycle.The total life expected for bearing is 3×10^6 revolution at a liability of 94 percent.select the bearing by calculating; a)Net dynamic load for the bearing b)load rating of the bearing from the manufacturers cataloguearrow_forwardAnswer this ASAP plz A double row angular contact ball bearing is used in the engine compressor to accept radial loads of 6000 N and axial loads of 3000 N, operating at 2400 rpm for an average life of 7 years at 8 hours per day. Assume that the shock load is light. Select the appropriate bearing number. Note: the equivalent dynamic load is the dynamic equivalent radial load times the service factor.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License